Browsing Journal of Engineering for Gas Turbines and Power by Title
Now showing items 1-20 of 9033
-
150 kwe Supercritical Closed Cycle System
(The American Society of Mechanical Engineers (ASME), 1971)This paper explores the potential applicability of the Supercritical (Feher) Thermodynamic Power Cycle to advanced ground nuclear power systems. The supercritical cycle is a closed cycle heat ... -
1991 Soichiro Honda Lecture: Energy, Efficiency, and the Environment: Three Big Es of Transportation
(The American Society of Mechanical Engineers (ASME), 1992)The three big Es of transportation are Energy, Efficiency, and the Environment. As the clouds of global climate change and the desire to rely less on Mid-East crude builds, how do manufacturers ... -
1993 Soichiro Honda Lecture: The Challenges of Change in the Auto Industry: Why Alternative Fuels?
(The American Society of Mechanical Engineers (ASME), 1994)Development of vehicles to operate on nonpetroleum fuels began in earnest in response to the energy shocks of the 1970s. While petroleum will remain the predominant transportation fuel for a ... -
1997 Soichiro Honda Lecture: Pathways to Achieving a New Generation of Engines for Personal Transportation
(The American Society of Mechanical Engineers (ASME), 2000)As we move into the twenty-first century the spread of affluence to a greater portion of an ever growing world population, coupled with dwindling reserves of crude oil, will make it imperative ... -
1D Engine Simulation of a Small HSDI Diesel Engine Applying a Predictive Combustion Model
(The American Society of Mechanical Engineers (ASME), 2008)The paper analyzes the operations of a small high speed direct injection (HSDI) turbocharged diesel engine by means of a parallel experimental and computational investigation. As far as the ... -
25Years of BBC/ABB/Alstom Lean Premix Combustion Technologies
(The American Society of Mechanical Engineers (ASME), 2007)The paper will show the development of lean premix combustion technologies in BBC, ABB, and Alstom gas turbines. Different technologies have been developed and applied in Brown Boveri Company ... -
2750 Deg F Engine Test of a Transpiration Air-Cooled Turbine
(The American Society of Mechanical Engineers (ASME), 1971)The development of gas turbine engines for advanced subsonic and supersonic aircraft as well as for potential utilization of these high performance engines for stationary and marine applications ... -
3-D Laser Anemometer Measurements in a Labyrinth Seal
(The American Society of Mechanical Engineers (ASME), 1991)The flow field inside a seven-cavity labyrinth seal with a 0.00127-m clearance was measured using a 3-D laser-Doppler anemometer system. Through the use of this system, the mean velocity vector ... -
30 Years of Dry-Low-NOx Micromix Combustor Research for Hydrogen-Rich Fuels—An Overview of Past and Present Activities
(The American Society of Mechanical Engineers (ASME), 2021)This paper presents an overview of the past and present of low-emission combustor research with hydrogen-rich fuels at Aachen University of Applied Sciences (AcUAS). In 1990, AcUAS started developing the dry-low-NOx Micromix ... -
3500 SI Engine Application Flexibility
(The American Society of Mechanical Engineers (ASME), 1991)The 3500 Spark-Ignited Engine is a 170 mm bore by 190 mm stroke family including 8, 12, and 16-cylinder models rated at 54 bkW per cylinder. Initial production included low-emission versions ... -
3D RANS Simulation of Turbulent Flow and Combustion in a 5 MW Reverse-Flow Type Gas Turbine Combustor
(The American Society of Mechanical Engineers (ASME), 2010)This study is concerned with 3D RANS simulation of turbulent flow and combustion in a 5 MW commercial gas turbine combustor. The combustor under consideration is a reverse flow, dry low NOx ... -
3D Transonic Potential Flow Computation in an Axial-Flow Compressor Rotor by an Approximate Factorization Scheme
(The American Society of Mechanical Engineers (ASME), 1986)A conservative full-potential equation of 3D transonic flow in a turbomachine has been derived with the tensor method and expressed with respect to nonorthogonal curvilinear coordinates, and a ... -
9 ppm NOx/CO Combustion System for “F” Class Industrial Gas Turbines
(The American Society of Mechanical Engineers (ASME), 2001)The Dry Low NOx (DLN) -2.6 combustion system has achieved emission rates of lower than 9 ppm NOx (dry, corrected to 15 percent O2) and CO from 50 to 100 percent load for the GE MS7001FA ... -
A Baseload Gas Turbine to Meet Utility Requirements for Reliability and Availability
(The American Society of Mechanical Engineers (ASME), 1982)The coal gasifier, gas turbine, combined cycle is a superior baseload electric generating system. It promises lower fuel cost, lower operating and maintenance cost, and superior siting and ... -
A Blade Loss Response Spectrum for Flexible Rotor Systems
(The American Society of Mechanical Engineers (ASME), 1985)A shock spectrum procedure is developed to estimate the peak displacement response of linear flexible rotor-bearing systems subjected to a step change in unbalance (i.e., a blade loss). A ... -
A Blade Theory of an Impeller With an Arbitrary Surface of Revolution
(The American Society of Mechanical Engineers (ASME), 1971)In this report a method of analyzing subsonic inviscid flow between blades on a stream surface of revolution of a turbomachine, which may be an axial, a radial, or a mixed-flow type, is ... -
A Blade-by-Blade Tip Clearance Measurement System for Gas Turbine Applications
(The American Society of Mechanical Engineers (ASME), 1995)It is difficult to make a reliable measurement of running clearance in the hostile environment over the blading of a modern gas turbine. When engine manufacturers require the measurement to ... -
A Blade-to-Blade Solution of the Flow in a Centrifugal Compressor Impeller with Splitters
(The American Society of Mechanical Engineers (ASME), 1980)The matrix through flow analysis is used to predict the blade-to-blade flow in a centrifugal compressor impeller which contains splitters (half vanes). The presence of solid boundaries in the ... -
A Blockage Model for Centrifugal Compressor Impellers
(The American Society of Mechanical Engineers (ASME), 1981)This paper presents and discusses the results of an analysis in which the blockage distributions of four impellers were deduced from shroud static pressure measurements. The purpose of the ... -
A Bulk Flow Model for Off-Centered Honeycomb Gas Seals
(The American Society of Mechanical Engineers (ASME), 2007)A computational analysis for prediction of the static and dynamic forced performance of gas honeycomb seals at off-centered rotor conditions follows. The bulk-flow analysis, similar to the ...