Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1721-1740 of 3257
-
Spall Study in Mild Steel
(The American Society of Mechanical Engineers (ASME), 1997)The influence of inertial, thermal, and rate-sensitive effects on the void growth at high strain rate in a thermal-viscoplastic solid is investigated by means of a theoretical model proposed ... -
Mechanical Properties of Aircraft Materials Subjected to Long Periods of Service Usage
(The American Society of Mechanical Engineers (ASME), 1997)This paper evaluates changes in the behavior of aircraft materials which result from aging and/or corrosion that occurs during long periods of service usage. The primary objective was to determine ... -
Analysis for Cold Die Compaction of Stainless-Steel Powder
(The American Society of Mechanical Engineers (ASME), 1997)Densification behavior of 316L stainless-steel powder under die pressing was studied. The friction effects between the powder and the die wall under different die pressing modes were also ... -
Fatigue Crack Growth of β-21S Titanium Alloy Under Constant Amplitude and miniTWIST Flight Spectra at 25°C and 175°C
(The American Society of Mechanical Engineers (ASME), 1997)β-21S titanium alloy sheet fatigue crack growth behavior was investigated at 25°C and 175°C under constant amplitude (R = 0.1 and 0.5) and miniTWIST flight spectra. Based upon nominal ... -
A Unified Damage Approach for Predicting Forming Limit Diagrams
(The American Society of Mechanical Engineers (ASME), 1997)Plastic deformation in sheet metal consists of four distinct phases, namely, uniform deformation, diffuse necking, localized necking, and final rupture. The last three phases are commonly known ... -
Modeling Damage Evolution in a Hybrid Ceramic Matrix Composite Under Static Tensile Load
(The American Society of Mechanical Engineers (ASME), 1997)In this investigation, damage evolution in a unidirectional hybrid ceramic composite made from Nicalon and SiC fibers in a Lithium Aluminosilicate (LAS) glass matrix was studied. The static ... -
Creep-Induced Cleavage Fracture in WIPP Salt Under Indirect Tension
(The American Society of Mechanical Engineers (ASME), 1997)The phenomenon of cleavage fracture initiation in rock salt undergoing concurrent creep was studied experimentally using the Brazilian indirect tension test technique. The tensile creep and cleavage ... -
Modeling and Identification of Elastic-Plastic Systems Using the Distributed-Element Model
(The American Society of Mechanical Engineers (ASME), 1997)A modeling technique is proposed for a class of distributed-element models, which is able to account for the multi-axial Bauschinger effect without any additional kinematic hardening rules. The ... -
The Role of Rate Effects and of Thermomechanical Coupling in Shear Localization
(The American Society of Mechanical Engineers (ASME), 1997)A dislocation density related constitutive model that accounts for the strain-rate sensitivity of the flow stress and, notable, of the strain-hardening coefficient was applied to describe adiabatic ... -
Parameter Estimation for an Internal Variable Model Using Nonlinear Optimization and Analytical/Numerical Response Sensitivities
(The American Society of Mechanical Engineers (ASME), 1997)This paper demonstrates through examples that erroneous material constants for complex visco-plastic material models can be obtained from simultaneous parameter estimation by nonlinear optimization ... -
An Experimental Investigation Into the Relationship Between Temperature-Time History and Surface Roughness in the Spray Quenching of Aluminum Parts
(The American Society of Mechanical Engineers (ASME), 1996)Repeated heat-quench cycles of Al-1100 samples resulted in increased surface roughness and corresponding shifts in the temperature-time cooling curve towards shorter overall quench periods. Three ... -
Residual Stress Measurement in 304 Stainless Steel Weld Overlay Pipes
(The American Society of Mechanical Engineers (ASME), 1996)Welding overlay repair (WOR) is commonly employed to rebuild piping systems suffering from intergranular stress corrosion cracking (IGSCC). To understand the effects of this repair, it is necessary ... -
An Investigation of Necking Instability in Fiber Reinforced Polypropylene
(The American Society of Mechanical Engineers (ASME), 1996)Thermoplastic composite materials hold considerable promise for increased use in low cost high volume applications because of the potential for processing by solid phase forming. Unfortunately, ... -
Impact Resistance and Fracture Toughness of Vanadium-Based Microalloyed Forging Steel in the As-Forged and Q&T Conditions
(The American Society of Mechanical Engineers (ASME), 1996)Microalloyed (MA) steels are a family of steels which are becoming an increasingly important economic alternative to the traditional quenched and tempered (Q&T) steels. Impact resistance and ... -
Viscoplastic Behavior of a Notch Root at 650°C: ISDG Measurement and Finite Element Modeling
(The American Society of Mechanical Engineers (ASME), 1996)Viscoplastic behavior of the nickel-based superalloy, Inconel 718, at a notch root has been investigated by conducting isothermal tensile, creep and cyclic elastoplastic tests at 650°C which ... -
Thermomechanical and Isothermal Fatigue Behavior of Bare and Coated Superalloys
(The American Society of Mechanical Engineers (ASME), 1996)Thermomechanical fatigue (TMF) and isothermal fatigue (IF) experiments were performed on bare Mar-M246 as well as bare and coated Mar-M247 nickel based superalloys at strain ranges from 0.335 ... -
Overcoming Limitations of the Conventional Strain-Life Fatigue Damage Model
(The American Society of Mechanical Engineers (ASME), 1996)The strain-based approach to fatigue life prediction usually relies on the conventional strain-life equation which correlates the elastic and plastic strain to the life. The correlation is based ... -
Fatigue Crack Growth Properties of a Cryogenic Structural Steel at Liquid Helium Temperature
(The American Society of Mechanical Engineers (ASME), 1996)The structural materials of the coils of superconducting magnets utilized in thermonuclear fusion reactors are used at liquid helium (4.2 K) temperatures and are subjected to repeated thermal ... -
A Mechanical Material Model for Aluminium Extrusions During On-line Quenching
(The American Society of Mechanical Engineers (ASME), 1996)A material model is suggested, suitable for modelling the mechanical behaviour of aluminium sections, from directly after the extrusion and throughout the on-line quenching to room temperature. ... -
Stress Calculation Error Analysis for Incremental Hole-Drilling Residual Stress Measurements
(The American Society of Mechanical Engineers (ASME), 1996)The incremental hole-drilling method for measuring non-uniform residual stresses gives stress results that are very sensitive to errors in the measured data. The resulting stress errors can easily ...