Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1741-1760 of 3257
-
A Two Surface Plasticity Model With Bounding Surface Softening
(The American Society of Mechanical Engineers (ASME), 1996)Two surface plasticity models have been used increasingly in recent years to model not only uniaxial, cyclic plasticity but also multiaxial and nonproportional histories. A two surface model is ... -
Response of Resin Transfer Molded (RTM) Composites Under Reversed Cyclic Loading
(The American Society of Mechanical Engineers (ASME), 1996)Compressive behavior and the tension-compression fatigue response of resin transfer molded IM7 PW/PR 500 composite laminate with a circular notch have been studied. Fatigue damage characteristics ... -
Analysis of Layer Waviness in Flat Compression-Loaded Thermoplastic Composite Laminates
(The American Society of Mechanical Engineers (ASME), 1996)A finite element analysis was used to investigate layer waviness effects in flat compression-loaded composite laminates. Stress distributions in the vicinity of the layer waves as well as the ... -
Fluid and Matrix Components of Polyurethane Foam Behavior Under Cyclic Compression
(The American Society of Mechanical Engineers (ASME), 1996)Semi-rigid polyurethane foam specimens were compressed to 25, 50, or 75 percent strain at nominal strain rates of 0.14/s, 1.4/s or 14/s for up to 100 cycles. The loads carried by the fluid ... -
Constitutive Modeling of the Visco-Plastic Response of Hastelloy-X and Aluminum Alloy 8009
(The American Society of Mechanical Engineers (ASME), 1996)The viscoplastic behavior of advanced, high temperature, metallic alloys is characterized using the Bodner Partom unified constitutive model. Material parameters for both Hastelloy-X and Aluminum ... -
The Effect of Stress-State on the Large Strain Inelastic Deformation Behavior of 304L Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1996)In metals, large strain inelastic deformation processes such as the formation of a preferred crystallographic orientation (crystallographic texture) and strain hardening processes such as the ... -
Analytical, Numerical, and Experimental Studies of Effective Elastic Properties of Periodically Perforated Materials
(The American Society of Mechanical Engineers (ASME), 1996)Comprehensive analytical, finite element analysis and experimental studies are made of the interaction between closely spaced multiple circular holes. The analytical model utilizes the technique ... -
A Study of Kerf Characteristics in Abrasive Waterjet Machining of Graphite/Epoxy Composite
(The American Society of Mechanical Engineers (ASME), 1996)Kerf geometry, kerf wall features, and cutting front characteristics of an Abrasive Waterjet (AWJ) machined Graphite/Epoxy (Gr/Ep) laminate were studied. A macroscopic analyses suggests that ... -
Optimization of the Manufacturing Process of a Titanium Aluminide Metal Matrix Composite Using a Viscoplastic Constitutive Theory
(The American Society of Mechanical Engineers (ASME), 1996)The thermomechanical behavior of a titanium aluminide metal matrix composite reinforced with silicon carbide fibers is computationally investigated to determine an optimum manufacturing process. The ... -
Determination of Nonuniform Residual Stresses Using the Ring-Core Method
(The American Society of Mechanical Engineers (ASME), 1996)This paper considers residual stress analysis using the ring-core method. In particular, the so-called integral equation method is applied to evaluate nonuniform residual stress fields. The proposed ... -
Nonunique Dynamic Equilibrium Constitutive Relation of Metal Powder Depending on its Microstructure
(The American Society of Mechanical Engineers (ASME), 1996)It was observed in an earlier work by Morimoto et al. [Inst. Phys. Conf. Ser. No. 70, Oxford 1984, p. 427] that the dynamic compact of an aluminium powder medium had greater flakiness and ... -
Stress-Strain Analysis of Single-Lap Composite Joints Under Tension
(The American Society of Mechanical Engineers (ASME), 1996)Based on the laminated anisotropic plate theory, an analytical model is proposed to determine the stress and strain distributions of adhesive-bonded composite single-lap joints under tension. The ... -
On the Constitutive Response of 63/37 Sn/Pb Eutectic Solder
(The American Society of Mechanical Engineers (ASME), 1996)The constitutive response of 63/37 Sn/Pb eutectic solder is studied under uniaxial tension. Stress-strain tests were performed under a wide range of applied strain rate, and creep tests were ... -
Prediction of Residual Stresses in Welded T- and I-Joints Using Inherent Strains
(The American Society of Mechanical Engineers (ASME), 1996)In order to develop a predicting method of residual stresses in fillet welded T- and I-joints, a concept of inherent strain, being regarded as a source of the residual stresses, was introduced. ... -
Effect of Carbonization Heating Rate, Microstructure, and Lay-Up on the Interlaminar Tensile Properties of a Two-Dimensional Carbon-Carbon Composite
(The American Society of Mechanical Engineers (ASME), 1996)A study of the effect of the carbonization heating rate, initial phenolic microstructure, and lamination lay-up on the interlaminar tensile (ILT) stiffness and strength (matrix-dominated properties) ... -
Verification of a Cohesive Zone Model for Ductile Fracture
(The American Society of Mechanical Engineers (ASME), 1996)In the present paper, ductile crack growth in an aluminium alloy is numerically simulated using a cohesive zone model under both plane stress and plane strain conditions for two different ... -
Burr/Breakout Model Development and Experimental Verification
(The American Society of Mechanical Engineers (ASME), 1996)The mechanisms of burr formation and breakout in orthogonal cutting are analyzed. A burr formation/breakout model for orthogonal cutting is proposed, based on the observation of SEM micro-machining ... -
Measurement of Residual Stresses in a Circular Ring Using the Successive Cracking Method
(The American Society of Mechanical Engineers (ASME), 1996)A method which we describe as the “successive cracking method” for measuring residual stresses in a circular ring is presented. In this method, the residual stresses are evaluated using a ... -
A Model of Residual Stress in the Fabrication of Thin Glass Films
(The American Society of Mechanical Engineers (ASME), 1996)We investigate the residual stress which occurs during fabrication of thin glass films. This research involves an innovative approach to modeling of residual stress which will be used to resolve ... -
Failure Prediction for Cross-Rolled Beryllium Sheet Material
(The American Society of Mechanical Engineers (ASME), 1996)A failure model for cross-rolled beryllium SR-200 sheets is developed for material loaded in a complex state of stress. Coefficients of the Tsai-Wu criterion are determined from a series of ...