Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1761-1780 of 3257
-
Tensile Failure of Stainless-Steel Notched Bars Under Hydrogen Charging
(The American Society of Mechanical Engineers (ASME), 1996)The influence of hydrogen embrittlement on the tensile failure of 316L stainless-steel notched bars is phenomenologically modeled in this paper. Tensile tests of notched samples suffering hydrogen ... -
Surface Strains Due to Face Loading of a Slot in a Layered Half-Space
(The American Society of Mechanical Engineers (ASME), 1996)A solution is presented that will allow the compliance method for residual stress measurement to be applied to layered materials. The solution is for surface strains due to arbitrary normal ... -
Hydrogen Embrittlement Characterization by Disk Pressure Tests: Test Analysis and Application to High Chromium Martensitic Steels
(The American Society of Mechanical Engineers (ASME), 1996)The paper reports and discusses the results of an experimental and numerical activity, aimed to the characterization of the influence of hydrogen on the mechanical properties of a few high ... -
ASME 1995 Nadai Lecture—Plasticity of Porous and Particulate Materials
(The American Society of Mechanical Engineers (ASME), 1996)The paper discusses the formulation of constitutive equation for those materials for which the irreversible changes of the volume is also to be taken into account. These are mainly geomaterials, ... -
Elastic Response of Flexible Polyurethane Foams in Uniaxial Tension
(The American Society of Mechanical Engineers (ASME), 1996)Flexible polymeric foams are used in many industrial applications, including cushioning, shock absorption, and noise suppression. There have not been many systematic studies on the characterization ... -
Cutting Forces in Orthogonal Cutting of Unidirectional GFRP Composites
(The American Society of Mechanical Engineers (ASME), 1996)The results of orthogonal cutting tests carried out on unidirectional glass fiber reinforced plastic composites, using HSS tools, are presented and discussed. During the tests, performed on a ... -
A State Variable Constitutive Model for Superplastic Ti-6Al-4V Based on Grain Size
(The American Society of Mechanical Engineers (ASME), 1996)In this work, the superplastic material behavior of Ti-6Al-4V has been correlated with the grain size of the a phase. Because this microstructural state variable is directly observable, the ... -
Accommodation of Springback Error in Channel Forming Using Active Binder Force Control: Numerical Simulations and Experiments
(The American Society of Mechanical Engineers (ASME), 1996)Springback in a forming process is due to the elastic deformation of the part during unloading. This manufacturing defect can be accounted for through proper tooling design or through proper ... -
A Finite-Element Work-Hardening Plasticity Model of the Uniaxial Compression and Subsequent Failure of Porous Cylinders Including Effects of Void Nucleation and Growth—Part II: Localization and Fracture Criteria
(The American Society of Mechanical Engineers (ASME), 1996)In Part I [1] of this paper, Gurson’s mixed hardening plasticity model with strain and stress-controlled nucleations, was used in a large deformation finite element program to study the plastic ... -
Nondestructive Detection of Damage Produced by a Sharp Indenter in Ceramics
(The American Society of Mechanical Engineers (ASME), 1996)The feasibility of an ultrasonic technique using normal-incident compressional waves and a thermal wave measurement technique was evaluated for their sensitivity to surface and subsurface damage ... -
Life Prediction Techniques for Variable Amplitude Multiaxial Fatigue—Part 2: Comparison With Experimental Results
(The American Society of Mechanical Engineers (ASME), 1996)An extensive multiaxial random fatigue test programme was conducted at room temperature using tubular specimens. Experiments were performed under combined tension/torsion and triaxial loading, ... -
Effect of Stress Ratio on Short Fatigue Crack Growth
(The American Society of Mechanical Engineers (ASME), 1996)A model of short fatigue crack growth is proposed, which is based on the blocked slip concept and the shear decohesion mechanism. The analysis is extended to the case of mean stress loading. ... -
Generalization of the Coffin Equations With Respect to the Effect of Large Mean Plastic Strain
(The American Society of Mechanical Engineers (ASME), 1996)Introduction of a correction factor accounting for large mean plastic strain to the kinetic law for the rate of damage per cycle is proposed. Integration of the corrected kinetic damage law ... -
Life Prediction Techniques for Variable Amplitude Multiaxial Fatigue—Part 1: Theories
(The American Society of Mechanical Engineers (ASME), 1996)Fatigue life prediction under multiaxis random loading is an extremely complex and intractable topic; only a few methods have been proposed in the literature. In addition, experimental results ... -
Energy Criterion for Fatigue Strength of Wood Structural Members
(The American Society of Mechanical Engineers (ASME), 1996)This report describes a mathematical model for fatigue strength of cellulosic materials under sinusoidal loading. The model is based on the Reiner-Weissenberg thermodynamic theory of strength in ... -
Thermal Phase Transformation and Residual Stress Estimation of Multi-Layer Materials for Cylindrical or Flat Shape
(The American Society of Mechanical Engineers (ASME), 1996)The estimation of the thermal, phase transformation, and residual stresses in multilayer materials during arbitrary loading is a complex problem, which is important in many manufacturing processes. ... -
Symmetric Branching of Mode II and Mixed-Mode Fatigue Crack Growth in a Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1996)Symmetric branching was found in all fatigue experiments carried out in a cruciform specimen in which the initial crack was in the middle of the specimen and at 45 deg with respect to the ... -
A Probabilistic Treatment of Microstructural Effects on Fatigue Crack Growth of Large Cracks
(The American Society of Mechanical Engineers (ASME), 1996)A probabilistic model has been developed for treating the effects of microstructural variation on the fatigue crack growth response of large cracks in structural alloys. The proposed methodology ... -
Strain Measurement in the Wavy-Ply Region of an Externally Pressurized Cross-Ply Composite Ring
(The American Society of Mechanical Engineers (ASME), 1996)Ply-level strains are determined in the cross-section of an externally pressurized cross-ply (3:1 circumferential to axial fiber ratio) graphite-epoxy ring containing an isolated circumferential ... -
Size Effect and Fracture Characteristics of Composite Laminates
(The American Society of Mechanical Engineers (ASME), 1996)Measurements of the size effect on the nominal strength of notched specimens of fiber composite laminates are reported. Tests were conducted on graphite/epoxy crossply and quasi-isotropic laminates. ...