Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1781-1800 of 3257
-
Mixed-Mode Fatigue Crack Growth in Stainless Steels Under Biaxial Loading
(The American Society of Mechanical Engineers (ASME), 1996)Mixed-Mode fatigue crack propagation tests were carried out in stainless-steel cruciform specimens in which a center initial crack oriented at 45 deg was loaded biaxially. When the loadings were ... -
Holographic Evaluation of Edge Delamination in Bars Bonded to a Rigid Support With Foam-Adhesive
(The American Society of Mechanical Engineers (ASME), 1996)When a bar having one end bonded to a rigid support with foam-adhesive is loaded, the high peeling stresses at the bonded edge foster edge delamination along the interface of bonding. Upon ... -
The Influence of Thermoplastic Film Interleaving on the Interlaminar Shear Strength and Mode I Fracture of Laminated Composites
(The American Society of Mechanical Engineers (ASME), 1996)Results are presented on the interlaminar shear strength (ILSS) and Mode I fracture toughness (GIC ) of glass/epoxy laminates interleaved with thermoplastic polyester films using four-point bending ... -
Behavior of a Unidirectional Metal-Matrix Composite Under Thermomechanical Loading
(The American Society of Mechanical Engineers (ASME), 1996)The thermoelastoplastic behavior of a unidirectional metal matrix composite (SiC/Al) under thermomechanical loading was studied with a micromechanical model based on the average field theory. The ... -
Analysis of the Failure of Ceramics Due to Subcritical Crack Growth
(The American Society of Mechanical Engineers (ASME), 1996)Failure conditions are assessed when ceramics exhibit Subcritical Crack Growth from preexisting flaws. In the framework of the weakest link theory and independent events hypothesis, a reliability ... -
Influence of Grinding Direction on Fracture Strength of Silicon Nitride
(The American Society of Mechanical Engineers (ASME), 1996)It is generally found that grinding transverse to the tensile stress direction in flexure bars subjected to four-point bending results in a lower strength compared to grinding in the longitudinal ... -
Automated Evaluation of Material Parameters of Viscoplastic Constitutive Equations
(The American Society of Mechanical Engineers (ASME), 1996)A method will be presented that allows for a special class of viscoplastic constitutive models a fast and safe determination of the material parameters. All parameters are determined simultaneously ... -
Determination of Biaxial Residual Stresses by a Holographic-Hole Drilling Technique
(The American Society of Mechanical Engineers (ASME), 1996)A technique is described for the rapid determination of residual stresses through the combined use of hole drilling and holographic interferometry. A small diameter blind hole is drilled into ... -
Influence of Strain Rate and Temperature on the Radial Compression Behavior of Wet Spruce
(The American Society of Mechanical Engineers (ASME), 1996)In the mechanical pulping process, wood is treated in compression and in shear at high temperatures in the wet state, to separate the fibers and also to increase the bonding ability and ... -
Experiments on the Ratchetting Behavior of AISI 316L(N) Austenitic Steel at Room Temperature
(The American Society of Mechanical Engineers (ASME), 1996)Uniaxial tension-compression ratchetting tests were performed on AISI 316 L(N) austenitic stainless steel at room temperature. The mean stresses were low in comparison to the stress amplitudes. ... -
Micromechanical Analysis of Dynamic Behavior of Conventional and Negative Poisson’s Ratio Foams
(The American Society of Mechanical Engineers (ASME), 1996)Both conventional and negative Poisson ’s ratio foams exhibit dispersion of acoustic waves, as well as cut-off frequencies, at which the group velocity tends to zero. This macroscopic behavior ... -
Role of Welding Parameters in Determining the Geometrical Appearance of Weld Pool
(The American Society of Mechanical Engineers (ASME), 1996)A three-dimensional numerical model is developed to describe the fluid flow and heat transfer in weld pools. Both full penetration and free deformation of the top and bottom weld pool surfaces ... -
Interactive Growth of Multiple Fiber-Bridged Matrix Cracks in Unidirectional Composites
(The American Society of Mechanical Engineers (ASME), 1996)A model is developed for monotonic and cyclic fiber sliding in a fiber-reinforced composite containing multiple cracks. The model is used to study the fatigue growth of multiple cracks in a ... -
An Experimental Study Evaluating Macroscopic Cavity Interactions as a Model of Microvoid Ductility
(The American Society of Mechanical Engineers (ASME), 1996)An experimental study of the interactions between macroscopic cavities was conducted. The goal was to determine simple cavity arrangements producing deformations similar to commonly observed features ... -
Analysis and Testing of Dynamic Micromechanical Behavior of Composite Materials at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1996)This paper describes the use of a recently developed high temperature impulse-frequency response apparatus to directly measure dynamic modulus and internal damping of high temperature composite ... -
Correlation of Tensile and Bending Strength of Composites With a Circular Hole
(The American Society of Mechanical Engineers (ASME), 1996)While significant studies have been conducted on composites containing a circular or an elliptic hole under tensile loading, few investigations have been reported on notched composites under ... -
Nonlinear Elastic Behavior of Unidirectional Composites With Fiber Waviness Under Compressive Loading
(The American Society of Mechanical Engineers (ASME), 1996)Nonlinear elastic behavior of unidirectional composites with fiber waviness under compressive loading was investigated theoretically and experimentally. Unidirectional carbon/epoxy composites with ... -
Life Prediction of Notched Specimens Using Multiaxial Surface and Subsurface Strain Analyses
(The American Society of Mechanical Engineers (ASME), 1996)Multiaxial fatigue life prediction analyses are applied to notched specimens subjected to high strain constant amplitude loading. The specimens are made from isotropic and anisotropic batches of ... -
A Study on the Distribution of Residual Stress Due to Surface Induction Hardening
(The American Society of Mechanical Engineers (ASME), 1996)A finite element method (FEM) is used here to analyse the distribution of residual stresses generated by surface induction hardening. The analysis considers both transformation induced plasticity ... -
Measuring Method for Residual Stresses in Explosively Clad Plates and a Method of Residual Stress Reduction
(The American Society of Mechanical Engineers (ASME), 1996)In this paper, a new layer removal method for measurement of local residual stress through the thickness of clad plates is developed using inherent strain which is considered a source of ...