Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1801-1820 of 3257
-
Architecture of Functionally Graded Ceramic Coatings Against Surface Thermal Fracture
(The American Society of Mechanical Engineers (ASME), 1996)An analytical study was performed to study the effect of architecture on the initiation of surface cracking in multilayer ceramic coatings. Two modes of crack initiation were considered: 1) ... -
Design Curve to Characterize Fatigue Strength
(The American Society of Mechanical Engineers (ASME), 1996)Fatigue (S-N) data exhibit relatively large scatter. For design purposes, an S-N curve that characterizes fatigue strength is required. This curve should lie on the lower, or safe, side of the ... -
A Unified Approach to Physically Based Weakest-Link Theories for Multiaxial Fracture of Ceramics
(The American Society of Mechanical Engineers (ASME), 1996)The paper discusses two physically based weakest-link approaches, commonly adopted to evaluate the reliability of ceramic components in multiaxial states of stress (namely, Evans’ multiaxial elemental ... -
A Probabilistic Micromechanics Model for Damaged Composites
(The American Society of Mechanical Engineers (ASME), 1996)The generalized method of cells, an interfacial constitutive model and a probabilistic model are combined to yield an approach for modeling the stress-strain response of fibrous composites with ... -
The Prediction of the Flow Stress of an Extra-Low Carbon Steel in the Two-Phase Region Using Continuous Cooling Curves
(The American Society of Mechanical Engineers (ASME), 1996)Continuous cooling curves of an extra-low carbon steel under three cooling rates are measured. The flow stress of the steel is established in compression tests during which the temperature is ... -
Densification Forming of Alumina Powder—Effects of Power Law Creep and Friction
(The American Society of Mechanical Engineers (ASME), 1996)High temperature forming processes of alumina powder compacts were analyzed by using constitutive equations which are capable of predicting densification and grain growth under diffusional creep ... -
High Temperature Densification Forming of Alumina Powder—Constitutive Model and Experiments
(The American Society of Mechanical Engineers (ASME), 1996)Densification and grain growth of alumina powder compacts were investigated under pressureless sintering, sinter forging, and hot pressing. A set of constitutive equations by Kwon et al. was ... -
Thermodynamic Law of Corresponding Shock States in Flexible Polymeric Foams
(The American Society of Mechanical Engineers (ASME), 1996)Based on thermodynamic considerations and experimental data on isothermal compression of elastomeric foams, a simple equation of state of flexible polymeric foams was developed. The developed ... -
Effect of Architecture on the Strength of Braided Tubes Under Biaxial Tension and Compression
(The American Society of Mechanical Engineers (ASME), 1996)Braided preforms of carbon fiber are under consideration for structural applications because of the potential for automated fabrication and possible improvement in through-the-thickness properties, ... -
Carbide Coarsening During Creep in 12 Percent CrMoV Steel
(The American Society of Mechanical Engineers (ASME), 1996)Carbide coarsening has been investigated in a 12 percent CrMoV steel. Studies in the gauge length (creep exposed) and in the head (stress free ageing) for both interrupted and ruptured creep ... -
A Dislocation Density Based Constitutive Model for Cyclic Deformation
(The American Society of Mechanical Engineers (ASME), 1996)A new constitutive model describing material response to cyclic loading is presented. The model includes dislocation densities as internal variables characterizing the microstructural state of the ... -
A Study of the Dynamic Behavior of Elastomeric Materials Using Finite Elements
(The American Society of Mechanical Engineers (ASME), 1996)A numerical method is described for determining a dynamic finite element material model for elastomeric materials loaded primarily in compression. The method employs data obtained using the Split ... -
Creep in Building Stones Under Tensile Conditions
(The American Society of Mechanical Engineers (ASME), 1996)Careful structural analyses of ancient stone constructions methodically showed crack openings under tensile stresses notably lower than the corresponding strength limits. Based on this observation, ... -
An Investigation of the Formability of Long Fiber Thermoplastic Composite Sheets
(The American Society of Mechanical Engineers (ASME), 1995)An experimental and analytical investigation was undertaken to improve understanding of the form of long fiber reinforced thermoplastic sheets. The materials tested contained 30 percent by weight ... -
Crack Growth Rate Behavior of a Titanium-Aluminide Alloy During Isothermal and Nonisothermal Conditions
(The American Society of Mechanical Engineers (ASME), 1995)Observations of isothermal fatigue, isothermal fatigue with superimposed load hold times, and thermomechanical fatigue (TMF) crack growth rate behavior of Ti-24Al-11Nb are presented and compared ... -
The Importance of Material Structure in the Laser Cutting of Glass Fiber Reinforced Plastic Composites
(The American Society of Mechanical Engineers (ASME), 1995)A previously proposed micromechanical formula, aiming to predict the vaporization energy Qv of composite materials as a function of fiber and matrix properties and fiber volume ratio, was assessed. ... -
An Experimental Investigation of Damage Evolution in a Ceramic Matrix Composite
(The American Society of Mechanical Engineers (ASME), 1995)The mechanical behavior of a glass-ceramic matrix composite, SiC/CAS (calcium aluminosilicate reinforced with unidirectional SiC fibers), is studied. Results based on uniaxial tension experiments ... -
Thermomechanical Fatigue Behavior of a Quasi-lsotropic SCS-6/Ti-15-3 Metal Matrix Composite
(The American Society of Mechanical Engineers (ASME), 1995)The response of a quasi-isotropic laminate of metal matrix composite, SCS-6/Ti-15-3 in a thermomechanical fatigue (TMF) environment was investigated. To achieve this, three sets of fatigue tests ... -
Experimental Techniques for Dynamic Characterization of Composite Materials
(The American Society of Mechanical Engineers (ASME), 1995)This research combines theoretical and experimental approaches for dynamic material characterization of composite materials. The samples studied include continuous fiber graphite/epoxy beams with ... -
The Role of Gas Dissolution and Induced Crystallization During Microcellular Polymer Processing: A Study of Poly (Ethylene Terephthalate) and Carbon Dioxide Systems
(The American Society of Mechanical Engineers (ASME), 1995)One of the critical steps in the production of microcellular polymers is the dissolution of gas into a polymer matrix. In this paper, the formation of a gas and semi-crystalline thermoplastic ...