Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1701-1720 of 3257
-
Deformation Micromechanics of Regenerated Cellulose Fibers Using Raman Spectroscopy
(The American Society of Mechanical Engineers (ASME), 1997)It is demonstrated that Raman spectroscopy can be used to study the molecular deformation of TENCELR fibers. It is shown that the peak positions of the 895 cm−1 and 1095 cm−1 Raman bands ... -
Visco-Hyperelastic Model for Filled Rubbers Used in Vibration Isolation
(The American Society of Mechanical Engineers (ASME), 1997)The short time and cyclic behavior of filled rubbers used in vibration isolation in the frequency range 10−2 to 102 rad/s is examined. A form of the free-energy function consistent with the ... -
Thermomechanical Effects Associated With Crystallization of Rubber Under Stretch and During Slow Extension
(The American Society of Mechanical Engineers (ASME), 1997)A natural rubber sample which crystallizes after stretching normally shows stress relaxation associated with this crystallization and normally ends up at a stress lower than that of the fully ... -
Dynamic Response of Epon 828/T-403 Under Multiaxial Loading at Various Temperatures
(The American Society of Mechanical Engineers (ASME), 1997)The mechanical response and failure behavior of Epon 828/T-403 epoxy were experimentally obtained over a strain rate range of 1.7 × 10−5 to 4.7 × 103 s−1 and a temperature range of ... -
On the Prediction of Stress Relaxation From Known Creep of Nonlinear Materials
(The American Society of Mechanical Engineers (ASME), 1997)A method to predict the nonlinear relaxation behavior from creep experiments of nonlinear viscoelastic materials is presented. It is shown that for given nonlinear creep properties, and creep ... -
Dynamics of Thick Viscoelastic Beams
(The American Society of Mechanical Engineers (ASME), 1997)A viscoelastic higher-order thick beam finite element formulation is extended to include elastodynamic deformations. The material constitutive law is a special differential form of the Maxwell ... -
Axisymmetric Adhesion Tests of Pressure Sensitive Adhesives
(The American Society of Mechanical Engineers (ASME), 1997)The fracture mechanics of adhesion tests based on the contact of a flat punch or a spherical indenter with a thin elastic layer are studied. For a flat punch, existing literature data are ... -
A Presentation and Comparison of Two Large Deformation Viscoelasticity Models
(The American Society of Mechanical Engineers (ASME), 1997)In this paper we present a theory of finite deformation viscoelasticity. The presentation is not restricted to small perturbations from the elastic equilibrium in contrast to many viscoelasticity ... -
Large Deformations of Semicrystalline Polymer Modeled Using the Necking Network Concept
(The American Society of Mechanical Engineers (ASME), 1997)Previously, a physically-based elastic model has been used in the modeling of high temperature polymer deformation. While this has been successful in producing realistic shapes and forces in ... -
Multiaxial Nonlinear Viscoelastic Characterization and Modeling of a Structural Adhesive
(The American Society of Mechanical Engineers (ASME), 1997)Many polymeric materials, including structural adhesives, exhibit a nonlinear viscoelastic response. The nonlinear free volume approach is based on the Doolittle concept that the “free volume” ... -
Rate Dependent Deformation of Semi-Crystalline Polypropylene Near Room Temperature
(The American Society of Mechanical Engineers (ASME), 1997)We examine the strain rate dependent, large plastic deformation in isotropic semi-crystalline polypropylene at room temperature. Constant strain rate uniaxial compression tests on cylindrical ... -
Influence of Crosslinking on the Plastic Behavior of Amorphous Polymers at Large Strains
(The American Society of Mechanical Engineers (ASME), 1997)The mechanical properties of three grades of PMMA, one linear and two crosslinked, are investigated in tension below and above the glass transition temperature. It is found that strain-hardening ... -
Influence of Inclusion Microgeometry on Some Thermomechanical Properties of Isotropic Polymer-Matrix Composites
(The American Society of Mechanical Engineers (ASME), 1997)The influence of inclusion shape on some selected thermomechanical properties of isotropic viscoelastic composites is investigated by a micromechanical theory. These properties include: (i) the ... -
Theoretical and Experimental Evaluation of the Bond Strength Under Peeling Loads
(The American Society of Mechanical Engineers (ASME), 1997)Reliable applications of adhesively bonded joints require understanding of the stress distribution along the bond-line and the stresses that are responsible for the joint failure. To properly ... -
Fatigue Behavior of a Cross-Ply Metal Matrix Composite at Elevated Temperature Under the Strain Controlled Mode
(The American Society of Mechanical Engineers (ASME), 1997)A study was conducted to investigate the fatigue behavior of a cross-ply metal matrix composite subjected to fully-reversed, strain-controlled fatigue cycling at elevated temperature. The stress-strain ... -
Special Issue on Characterization and Modeling of Polymeric Material Systems
(The American Society of Mechanical Engineers (ASME), 1997) -
Recovering Nonisothermal Physical Aging Shift Factors Via Continuous Test Data: Theory and Experimental Results
(The American Society of Mechanical Engineers (ASME), 1997)For isothermal physical aging, a few simple tests to characterize the aging shift factors allow reasonable prediction of the mechanical response. In this paper, a new technique is developed to ... -
Analysis of Interfacial Failure in Particle-Filled Elastomers
(The American Society of Mechanical Engineers (ASME), 1997)The evolution of microdamage (interfacial dewetting) in highly filled elastomers under consideration of high deformation gradients is examined. The interface between hard (rigid, two-dimensional) ... -
A Laminated Plate Model of an Adhesive-Bonded Taper-Taper Joint Under Tension
(The American Society of Mechanical Engineers (ASME), 1997)An analytical model of the strain and stress distributions in a taper-taper adhesive-bonded joint between two composite flat plates has been developed using first-order laminated plate theory. A ... -
A Predictive Tool for Delaying Wrinkling and Tearing Failures in Sheet Metal Forming
(The American Society of Mechanical Engineers (ASME), 1997)In the sheet metal forming industry, there is increasing demand to lower manufacturing costs while also providing a decrease in product development turnaround period as well as lighter weight ...