Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1681-1700 of 3257
-
Discussion: “Measurement of Residual Stresses in a Circular Ring Using the Successive Cracking Method” (Kang, K. J., and Seol, S. Y., 1996, ASME J. Eng. Mater. Technol., 118, pp. 217–223)
(The American Society of Mechanical Engineers (ASME), 1997) -
A Methodology for Predicting Variability in Microstructurally Short Fatigue Crack Growth Rates
(The American Society of Mechanical Engineers (ASME), 1997)A finite element model, which implements single crystal constitutive relationships, was used to simulate fatigue cracks growing at the microstructural level. Plastic deformation (slip) was allowed ... -
Initiation of Surface and Interface Edge Cracks in Functionally Graded Ceramic Thermal Barrier Coatings
(The American Society of Mechanical Engineers (ASME), 1997)The initiation of surface and interface edge cracks in functionally graded ceramic thermal barrier coatings resulting from the application of a thermal load is studied. For a given specimen ... -
A Phenomenological Model for Cyclic Plasticity
(The American Society of Mechanical Engineers (ASME), 1997)A phenomenological model is proposed for cyclic plasticity based on the concept of distributed elements, which is capable of reflecting microstructural behavior of real materials under multiaxial ... -
Erratum: “Symmetric Branching of Mode II and Mixed-Mode Fatigue Crack Growth in a Stainless Steel” (ASME Journal Engineering Materials Technology, 1996, 118, pp. 356–361)
(The American Society of Mechanical Engineers (ASME), 1997) -
Response of SiCf/Si3N4 Composites Under Static and Cyclic Loading—An Experimental and Statistical Analysis
(The American Society of Mechanical Engineers (ASME), 1997)Monotonic tensile and fatigue response of continuous silicon carbide fiber reinforced silicon nitride (SiCf /Si3 N4 ) composites has been investigated. The monotonic tensile tests have been ... -
Modeling of High Homologous Temperature Deformation Behavior Using the Viscoplasticity Theory Based on Overstress (VBO): Part II—Characteristics of the VBO Model
(The American Society of Mechanical Engineers (ASME), 1997)Characteristics of the high homologous temperature VBO model under extreme conditions such as very fast and very slow tensile tests, long-term-creep and relaxation tests are investigated via ... -
A Constitutive Model and Its Identification for the Deformation Characterized by Dynamic Recovery
(The American Society of Mechanical Engineers (ASME), 1997)A constitutive model is presented to characterize the deformation behavior of materials at elevated temperatures that undergo dynamic recovery. Hot torsion tests were utilized to validate the ... -
In Situ Measurement of the Young’s Modulus of an Embedded Inclusion by Acoustic Microscopy
(The American Society of Mechanical Engineers (ASME), 1997)Alumina-silicate inclusions (shot) have been found to adversely affect the mechanical properties of a short alumina-silicate fiber reinforced aluminum alloy (A356). To better understand the differences ... -
Closure to “Discussion of ‘Measurement of Residual Stresses in a Circular Ring Using the Successive Cracking Method’” (1997, ASME J. Eng. Mater. Technol., 119, p. 116)
(The American Society of Mechanical Engineers (ASME), 1997) -
High Temperature Multiaxial Low Cycle Fatigue of CMSX-2 NI-Base Single Crystal Superalloy
(The American Society of Mechanical Engineers (ASME), 1997)This paper describes studies of the tension-torsion multiaxial low cycle fatigue of CMSX-2 Ni-base single crystal superalloy. Tension-torsion low cycle fatigue tests were carried out at 1173K ... -
Combined Bending and Torsional Fatigue of Woven Roving GRP
(The American Society of Mechanical Engineers (ASME), 1997)A study of biaxial fatigue of woven roving glass reinforced polyester (GRP) subjected to in-phase and out-of-phase cyclic bending and torsional moments is presented. To evaluate failure theories ... -
Modeling Foam Damping Materials in Automotive Structures
(The American Society of Mechanical Engineers (ASME), 1997)Foam damping materials judiciously placed in automotive structures efficiently reduce the vibration amplitudes of large, relatively flat exterior body panels such as the hood, roof, deck lid ... -
Constitutive Modeling and Material Characterization of Polymeric Foams
(The American Society of Mechanical Engineers (ASME), 1997)In this study, mechanical properties of three types of polymeric foams (polypropylene (PP), polystyrene (PS), and polyurethane (PU) foams) are investigated. Focus has been placed on the strain ... -
Numerical Analysis of Deep Drawing Process for Thermoplastic Composite Laminates
(The American Society of Mechanical Engineers (ASME), 1997)A numerical analysis including flow, heat transfer and residual stress is developed to simulate the deep drawing process of composite laminates with woven fabric microstructures. The governing ... -
Constitutive Equations for Solid Propellants
(The American Society of Mechanical Engineers (ASME), 1997)Mechanical behavior of the Space Shuttle redesigned solid rocket motor (RSRM) propellant is studied from a phenomenological point of view. Motivated by the study of the experimental data three ... -
Grain Size Modeling and Optimization of Rotary Forged Alloy 718
(The American Society of Mechanical Engineers (ASME), 1997)The study presented describes the simulation procedure and methodology used to develop two models for predicting recrystallized grain size in Alloy 718 billet. To simulate multiple pass forging ... -
A Numerical Study of Cavitation and Yield in Amorphous Polymer-Rubber Blends
(The American Society of Mechanical Engineers (ASME), 1997)A numerical study is presented of cavitation and yield in amorphous polymer-rubber blends in terms of a unit cell model involving an initially voided rubber particle. The particle is described ... -
Effect of Cure State on Stress Relaxation in 3501-6 Epoxy Resin
(The American Society of Mechanical Engineers (ASME), 1997)Little experimental work has been done to characterize how the viscoelastic properties of composite material matrix resins develop during cure. In this paper, the results of a series of creep ... -
Free Edge Stresses in Elastic and Viscoelastic Composites Under Uniaxial Extension, Bending, and Twisting Loadings
(The American Society of Mechanical Engineers (ASME), 1997)Time-dependent interlaminar stresses in elastic and viscoelastic laminated composites subjected to arbitrary combinations of axial extension, bending and/or twisting loads are obtained based on ...