Feasibility of Printed Circuit Board-Integrated Vibration Sensors for Condition Monitoring of Electronic SystemsSource: Journal of Electronic Packaging:;2019:;volume( 141 ):;issue: 003::page 31010Author:Brinkfeldt, Klas
,
Wetter, Göran
,
Lövberg, Andreas
,
Tegehall, Per-Erik
,
Andersson, Dag
,
Strandberg, Jan
,
Goncalves, Johnny
,
Söderlund, Jonas
,
Kwarnmark, Mikael
DOI: 10.1115/1.4043479Publisher: American Society of Mechanical Engineers (ASME)
Abstract: The increasing complexity of electronics in systems used in safety critical applications, such as self-driving vehicles, requires new methods to assure the hardware reliability of the electronic assemblies. Prognostics and health management (PHM) that uses a combination of data-driven and physics-of-failure models is a promising approach to avoid unexpected failures in the field. However, to enable PHM based partly on physics-of-failure models, sensor data that measure the relevant environment loads to which the electronics are subjected during its mission life are required. In this work, the feasibility to manufacture and use integrated sensors in the inner layers of a printed circuit board (PCB) as mission load indicators measuring impacts and vibrations has been investigated. A four-layered PCB was designed in which piezoelectric sensors based on polyvinylidenefluoride-co-trifluoroethylene (PVDF-TrFE) were printed on one of the laminate layers before the lamination process. Manufacturing of the PCB was followed by the assembly of components consisting of ball grid arrays (BGAs) and quad flat no-leads (QFN) packages in a standard production reflow soldering process. Tests to ensure that the functionality of the sensor material was unaffected by the soldering process were performed. Results showed a yield of approximately 30% of the sensors after the reflow soldering process. The yield was also dependent on sensor placement and possibly shape. Optimization of the sensor design and placement is expected to bring the yield to 50% or better. The sensors responded as expected to impact tests. Delamination areas were present in the test PCBs, which requires further investigation. The delamination does not seem to be due to the presence of embedded sensors alone but rather the result of a combination of several factors. The conclusion of this work is that it is feasible to embed piezoelectric sensors in the layers of a PCB.
|
Collections
Show full item record
contributor author | Brinkfeldt, Klas | |
contributor author | Wetter, Göran | |
contributor author | Lövberg, Andreas | |
contributor author | Tegehall, Per-Erik | |
contributor author | Andersson, Dag | |
contributor author | Strandberg, Jan | |
contributor author | Goncalves, Johnny | |
contributor author | Söderlund, Jonas | |
contributor author | Kwarnmark, Mikael | |
date accessioned | 2019-09-18T09:08:09Z | |
date available | 2019-09-18T09:08:09Z | |
date copyright | 5/24/2019 12:00:00 AM | |
date issued | 2019 | |
identifier issn | 1043-7398 | |
identifier other | ep_141_03_031010 | |
identifier uri | http://yetl.yabesh.ir/yetl1/handle/yetl/4259267 | |
description abstract | The increasing complexity of electronics in systems used in safety critical applications, such as self-driving vehicles, requires new methods to assure the hardware reliability of the electronic assemblies. Prognostics and health management (PHM) that uses a combination of data-driven and physics-of-failure models is a promising approach to avoid unexpected failures in the field. However, to enable PHM based partly on physics-of-failure models, sensor data that measure the relevant environment loads to which the electronics are subjected during its mission life are required. In this work, the feasibility to manufacture and use integrated sensors in the inner layers of a printed circuit board (PCB) as mission load indicators measuring impacts and vibrations has been investigated. A four-layered PCB was designed in which piezoelectric sensors based on polyvinylidenefluoride-co-trifluoroethylene (PVDF-TrFE) were printed on one of the laminate layers before the lamination process. Manufacturing of the PCB was followed by the assembly of components consisting of ball grid arrays (BGAs) and quad flat no-leads (QFN) packages in a standard production reflow soldering process. Tests to ensure that the functionality of the sensor material was unaffected by the soldering process were performed. Results showed a yield of approximately 30% of the sensors after the reflow soldering process. The yield was also dependent on sensor placement and possibly shape. Optimization of the sensor design and placement is expected to bring the yield to 50% or better. The sensors responded as expected to impact tests. Delamination areas were present in the test PCBs, which requires further investigation. The delamination does not seem to be due to the presence of embedded sensors alone but rather the result of a combination of several factors. The conclusion of this work is that it is feasible to embed piezoelectric sensors in the layers of a PCB. | |
publisher | American Society of Mechanical Engineers (ASME) | |
title | Feasibility of Printed Circuit Board-Integrated Vibration Sensors for Condition Monitoring of Electronic Systems | |
type | Journal Paper | |
journal volume | 141 | |
journal issue | 3 | |
journal title | Journal of Electronic Packaging | |
identifier doi | 10.1115/1.4043479 | |
journal fristpage | 31010 | |
journal lastpage | 031010-7 | |
tree | Journal of Electronic Packaging:;2019:;volume( 141 ):;issue: 003 | |
contenttype | Fulltext |