Journal of Fluids Engineering: Recent submissions
Now showing items 4001-4020 of 9024
-
Cavitation Tests on Hydrofoils Designed for Accelerating Flow Cascade; Report 4—Three Profiles Designed for High Head Kaplan Turbine
(The American Society of Mechanical Engineers (ASME), 1969)In pursuit of the studies previously reported [1–3], three profiles suited for application in the main blade elements of high head Kaplan turbines—two intended for sections near boss and one ... -
Straight Channel Diffuser Performance at High Inlet Mach Numbers
(The American Society of Mechanical Engineers (ASME), 1969)Measurements have been made of the pressure recovery of straight wall, single plane divergence diffusers with inlet Mach numbers between 0.2 and choking (0.2 ≤ Mt < 1.0). In contrast to ... -
Experiences on Startup and Trial Operation at Yards Creek Pumped Storage Project
(The American Society of Mechanical Engineers (ASME), 1969)Many problems were encountered during the startup and trial operation at Yards Creek. This paper describes the major problems and how they were resolved. There are many questions about pump-turbine ... -
One-Way Air Chambers for Pumping Plants
(The American Society of Mechanical Engineers (ASME), 1969)The one-way air chamber for suppressing water-column separation is described. Operation of the one-way air chamber during a power failure transient is explained. A typical problem solution is ... -
Note on Stress and Strain Redistribution in a Notched Plate Specimen During Cyclic Loading
(The American Society of Mechanical Engineers (ASME), 1969)A finite-element computational method is employed to determine the spatial distribution of stress and strain in a notched-plate fatigue specimen fabricated of mild steel. Because of cyclic strain ... -
A New Integral Method for Analyzing the Turbulent Boundary Layer With Arbitrary Pressure Gradient
(The American Society of Mechanical Engineers (ASME), 1969)For routine calculations of the properties of the incompressible turbulent boundary layer with arbitrary pressure gradient, the presently accepted method is the Karman integral technique, which ... -
The Performance of Pressure-Exchanger Dividers and Equalizers
(The American Society of Mechanical Engineers (ASME), 1969)Tests are reported which were carried out to establish the performance of pressure-exchanger dividers and equalizers using air as the working fluid. The effects of varying rotor speed, port ... -
Effects of Curvature on Laminar Boundary Layers in Sink-Type Flows
(The American Society of Mechanical Engineers (ASME), 1969)The two-dimensional, incompressible laminar boundary layer on a strongly curved wall in a converging channel is investigated for the special case of potential velocity inversely proportional to ... -
Water-Hammer Attenuation With a Tapered Line
(The American Society of Mechanical Engineers (ASME), 1969)An investigation has been made of the pressure attenuation that can be obtained through the application of a rigid tapered section located immediately upstream of a quick-closing valve or other ... -
Analysis and Control of Unsteady Flows in Natural Gas Piping Systems
(The American Society of Mechanical Engineers (ASME), 1969)In this paper the method of characteristics is used to provide a solution of the equations governing unsteady flow in natural gas pipelines. The validity of this approach is confirmed by ... -
Discussion: “Elastic-Plastic Stress Distribution in a Compressed Ring” (Chang, K. T., and Leopold, P. M., 1968, ASME J. Basic Eng., 90, pp. 435–440)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Experimental Study of the Effects of Orifice Plate Eccentricity on Flow Coefficients” (Miller, R. W., and Kneisel, O., 1969, ASME J. Basic Eng., 91, pp. 121–131)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Prediction of Flow of a Melted Plastic Through a Screw Extruder” (Kaiser, H., and Smith, C. W., 1969, ASME J. Basic Eng., 91, pp. 479–488)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Response of a Fluidic Air Gauge” (Moses, H. L., Small, D. A., and Cotta, G. A., 1969, ASME J. Basic Eng., 91, pp. 475–478)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Effects of Nonuniform Inlet Velocity Profiles on Flow Regimes and Performance in Two-Dimensional Diffusers” (Wolf, S., and Johnston, J. P., 1969, ASME J. Basic Eng., 91, pp. 462–474)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Pressure Transients in Hydraulic Pipelines” (Thorley, A. R. D., 1969, ASME J. Basic Eng., 91, pp. 453–460)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Velocity Distribution and Its Effect on the Accuracy of the Gibson Method of Water Measurement” (Johnson, G. Dugan, 1969, ASME J. Basic Eng., 91, pp. 434–438)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Cavitation Tests on Hydrofoils Designed for Accelerating Flow Cascade; Report 4—Three Profiles Designed for High Head Kaplan Turbine” (Numachi, F., 1969, ASME J. Basic Eng., 91, pp. 423–432)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Experiences on Startup and Trial Operation at Yards Creek Pumped Storage Project” (Swed, R. J., and Yang, K. H., 1969, ASME J. Basic Eng., 91, pp. 387–395)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Straight Channel Diffuser Performance at High Inlet Mach Numbers” (Runstadler, Jr., P. W., and Dean, Jr., R. C., 1969, ASME J. Basic Eng., 91, pp. 397–412)
(The American Society of Mechanical Engineers (ASME), 1969)