Journal of Fluids Engineering: Recent submissions
Now showing items 4021-4040 of 9024
-
Discussion: “A New Integral Method for Analyzing the Turbulent Boundary Layer With Arbitrary Pressure Gradient” (White, F. M., 1969, ASME J. Basic Eng., 91, pp. 371–376)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “One-Way Air Chambers for Pumping Plants” (Kephart, Jr., J. T., 1969, ASME J. Basic Eng., 91, pp. 383–385)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Effects of Curvature on Laminar Boundary Layers in Sink-Type Flows” (Gustafson, W. A., and Pelech, I., 1969, ASME J. Basic Eng., 91, pp. 353–358)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Water-Hammer Attenuation With a Tapered Line” (Tarantine, F. J., and Rouleau, W. T., 1969, ASME J. Basic Eng., 91, pp. 341–351)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Analysis and Control of Unsteady Flows in Natural Gas Piping Systems” (Stoner, M. A., 1969, ASME J. Basic Eng., 91, pp. 331–338)
(The American Society of Mechanical Engineers (ASME), 1969) -
The Prandtl-Kolmogorov Model of Turbulence With the Inclusion of Second-Order Terms
(The American Society of Mechanical Engineers (ASME), 1969) -
The Effect of Local Yielding on the Strain-Energy Release Rate
(The American Society of Mechanical Engineers (ASME), 1969)In a recent paper in the Journal of Basic Engineering [1], Forman presented numerical results for the strain-energy release rate of a crack in a finite width plate using the Dugdale model ... -
Wake Observations for Oscillating Cylinders
(The American Society of Mechanical Engineers (ASME), 1969) -
An Experimental Investigation of Fracture Criteria for Combined Extension and Bending
(The American Society of Mechanical Engineers (ASME), 1969)Experiments were performed on cracked plates loaded in combined extension and approximately cylindrical bending. A fracture criterion was developed from the Sih-Hartranft bending theory, which, ... -
The Notch-Bend Strength of Titanium, Aluminum, and Copper-Base Alloys in Heavy Sections
(The American Society of Mechanical Engineers (ASME), 1969)The notch-bend strength of four titanium, eight aluminum, and eight copper-base alloys was measured. Specimen sizes ranged from 0.4 to 4 in. in section thickness. All materials showed a geometrical ... -
Aluminum Wire by Cold Hydrostatic Extrusion
(The American Society of Mechanical Engineers (ASME), 1969)Electrical grade aluminum wire was made by hydrostatic extrusion. Extrusion ratios ranged from 2.5:1 to 630:1. The surface finishes, diametric variations, and electrical and mechanical properties ... -
Computerized Relaxation Applied to the Plane-Strain Indenter
(The American Society of Mechanical Engineers (ASME), 1969)A computer adaptation of Southwell’s Relaxation Method was developed for the solution of elastic-perfectly plastic stress distribution problems. This method was employed to study some aspects of ... -
In-Process Control of Residual Stress in Drawn Tubing
(The American Society of Mechanical Engineers (ASME), 1969)Experimental work directed toward the development of means for in-process control of residual stress during tube drawing is described. Experiments were done on 304 and 321 stainless steels, ... -
A Thermal Lattice Boltzmann Two-Phase Flow Model and Its Application to Heat Transfer Problems—Part 2. Integration and Validation
(The American Society of Mechanical Engineers (ASME), 2006)In the previous paper (Part 1) ( and , 2006, ASME J. Fluids Eng., 128, pp. 142–150), the multiphase isothermal lattice Boltzmann equation (LBE) model and single phase thermal LBE (TLBE) model ... -
In Memoriam
(The American Society of Mechanical Engineers (ASME), 2006)This special section of JFE is dedicated to Dr. Sankaraiyer Gopalakrishnan who unexpectedly passed away recently. Gopal, as we affectionately called him, served the Fluids Engineering Division ... -
Parametric Influence on the Wall-Thickness Changes and the Bulk Strain Behavior of Hollow-Drawn Tubing
(The American Society of Mechanical Engineers (ASME), 1969)The hollow-drawing behavior of tubing with γ0 values (ratio of initial wall thickness to outer radius) between 0 < γ0 < 1 was studied. The effect of various parameters on wall-thickness ... -
Improving Falling Ball Tests for Viscosity Determination
(The American Society of Mechanical Engineers (ASME), 2006)Laboratory experiments and numerical simulations are performed to determine the accuracy and reproducibility of the falling-ball test for viscosity determination in Newtonian fluids. The results ... -
Surfactant Use for Slug Flow Pattern Suppression and New Flow Pattern Types in a Horizontal Pipe
(The American Society of Mechanical Engineers (ASME), 2006)A set of experiments was performed to study flow pattern suppression in horizontal air-water pipe flow by means of surfactant additive. Results suggest that addition of the surfactant to the ... -
Relaxation Effects in Small Critical Nozzles
(The American Society of Mechanical Engineers (ASME), 2006)We computed the flow of four gases (He, N2, CO2, and SF6) through a critical flow venturi (CFV) by augmenting traditional computational fluid dynamics (CFD) with a rate equation that accounts ... -
Analysis of the Swirling Flow Downstream a Francis Turbine Runner
(The American Society of Mechanical Engineers (ASME), 2006)An experimental and theoretical investigation of the flow at the outlet of a Francis turbine runner is carried out in order to elucidate the causes of a sudden drop in the draft tube pressure ...