Journal of Fluids Engineering: Recent submissions
Now showing items 3981-4000 of 9024
-
Discussion: “Invariant Imbedding and Sequential Interpolating Filters for Nonlinear Processes” (Kagiwada, H. H., Kalaba, R. E., Schumitzky, A., and Sridhar, R., 1969, ASME J. Basic Eng., 91, pp. 195–199)
(The American Society of Mechanical Engineers (ASME), 1969) -
Decay of Symmetrical Laminar Distorted Profiles Between Flat Parallel Plates
(The American Society of Mechanical Engineers (ASME), 1969) -
Alignment Charts for the Properties of Shock-Ionized Argon
(The American Society of Mechanical Engineers (ASME), 1969) -
Stream Deflection Produced by a Cascade of Jet Flap Airfoils
(The American Society of Mechanical Engineers (ASME), 1969) -
Some Effects of Inlet Blockage and Aspect Ratio on Diffuser Performance
(The American Society of Mechanical Engineers (ASME), 1969) -
The Cause of White Etching Material Outlining Shell-Type Cracks in Rail-Heads
(The American Society of Mechanical Engineers (ASME), 1969)The cause of the white-etching regions outlining certain subsurface cracks in rail-heads was investigated. These cracks known as shells may propagate into “shelly spots,” i.e., deep spalls, usually ... -
An Investigation of Very Small Diameter Laminar Flow Orifices
(The American Society of Mechanical Engineers (ASME), 1969) -
Slip Flow in the Entrance of a Tube
(The American Society of Mechanical Engineers (ASME), 1969)This Note is concerned with velocity and pressure distributions in the entrance of a right circular tube with slip at the wall for incompressible flow. The method used by Campbell and Slattery ... -
Correction for the Ordinary Mangier Displacement Thickness for Slender Cones
(The American Society of Mechanical Engineers (ASME), 1969) -
Mechanical Aspects of the Dynamic Tear Test
(The American Society of Mechanical Engineers (ASME), 1969)The impact forces and specimen bending moments generated during the NRL dynamic tear test are interpreted in terms of the dynamics of the system and the fracture characteristics of the material. ... -
Dynamic Fracture Toughness of A533 Steel
(The American Society of Mechanical Engineers (ASME), 1969)The fracture toughness of A533 steel at room temperature, 0 deg and −70 deg F, was evaluated with 1 and 2-in-thick contoured double cantilever beam (DCB) specimens. To establish the effect ... -
Basic Concepts for Dynamic Fracture Testing
(The American Society of Mechanical Engineers (ASME), 1969) -
Static and Dynamic Low-Temperature KIc Behavior of Steels
(The American Society of Mechanical Engineers (ASME), 1969)To determine the crack-toughness behavior of steels subjected to high strain rates, a study was undertaken to establish the effects of strain rate and temperature on the KIc -values of steels. ... -
The Unsteady Flow and Wake Near an Oscillating Cylinder
(The American Society of Mechanical Engineers (ASME), 1969)This paper reports on velocity, pressure, and correlation measurements in the turbulent wake and the adjacent unsteady potential flow of a circular cylinder. Particular attention is given to the ... -
Factors Influencing the Plane-Strain Crack Toughness Values of a Structural Steel
(The American Society of Mechanical Engineers (ASME), 1969)An investigation was conducted to determine the effects of the variables; temperature, strain rate, and precracking fatigue-stress level, on plane-strain crack toughness values of a rate and ... -
Prediction of Flow of a Melted Plastic Through a Screw Extruder
(The American Society of Mechanical Engineers (ASME), 1969)A theory is formulated for predicting the variation in average pressure and the rise in average temperature in molten plastic along the axis of a screw extruder. The mathematical model is for ... -
Response of a Fluidic Air Gauge
(The American Society of Mechanical Engineers (ASME), 1969)The response of the back pressure signal resulting from nozzle flow suddenly restricted by a downstream surface is described. Experimental results are presented for the periodic signal from a ... -
Effects of Nonuniform Inlet Velocity Profiles on Flow Regimes and Performance in Two-Dimensional Diffusers
(The American Society of Mechanical Engineers (ASME), 1969)An analytical and experimental study on the effects of large distortions of inlet velocity profiles on flow regimes and performance in diffusers is reported. Experiments are restricted to flow ... -
Pressure Transients in Hydraulic Pipelines
(The American Society of Mechanical Engineers (ASME), 1969)Equations of motion for a cylindrical tube containing a fluid are developed from a consideration of the forces and moments in the tube wall. These equations are solved for boundary conditions ... -
Velocity Distribution and Its Effect on the Accuracy of the Gibson Method of Water Measurement
(The American Society of Mechanical Engineers (ASME), 1969)The author demonstrates that significant basic errors are introduced into the Gibson method of measuring water flow rates, even in uniform straight pipes, by failure to take account of velocity ...