Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 2761-2780 of 7723
-
Discussion: “Time Domain Optimization of a Vibration Absorber” (Bartel, Donald L., and Krauter, Allan I., 1971, ASME J. Eng. Ind., 93, pp. 799–803)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Sound and Vibration Transmission Through Panels and Tie Beams Using Statistical Energy Analysis” (Crocker, M. J., Battacharya, M. C., and Price, A. J., 1971, ASME J. Eng. Ind., 93, pp. 775–781)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Nonlinear Deformation of a Pressure Diaphragm in Contact With a Piston” (Soedel, Werner, and Cohen, Raymond, 1971, ASME J. Eng. Ind., 93, pp. 765–770)
(The American Society of Mechanical Engineers (ASME), 1971) -
Force and Stability Measurements on Models of Submerged Pipelines
(The American Society of Mechanical Engineers (ASME), 1971)The effect of currents on pipes anchored just above the ocean floor is the subject of this study. Lift, drag, and stability of two parallel pipes, parallel to a flat plane (the sea floor) ... -
Normal Mode Solution for the Vibrational Motions of Long Flexible Booms on the RAE Satellite
(The American Society of Mechanical Engineers (ASME), 1971)A normal mode analysis is applied to the Radio Astronomy Explorer satellite which uses four 750 ft booms arranged in an “X” configuration. The state variables consist of three Euler angles ... -
Three-Dimensional Analysis of Hypoid Gears
(The American Society of Mechanical Engineers (ASME), 1971)A three-dimensional photoelastic analysis using the stress-freezing and slicing techniques was conducted to obtain stress and load distributions in a hypoid gear pair. Precise full-scale plastic ... -
Large Sideward Deflections of Two-Hinged Circular Arches
(The American Society of Mechanical Engineers (ASME), 1971)Deflections and stress resultants are calculated for hinged-hinged circular arches subjected to a horizontal point load at the crown. The underlying theory is based on the Bernoulli-Euler hypothesis. ... -
The Optimum Design of Spatial Frames Using the Method of Constrained Steepest Descent With State Equations
(The American Society of Mechanical Engineers (ASME), 1971)This paper considers the design of a class of spatial frames which occur frequently in mechanical systems: plane frames with out-of-plane loads. The design objective is to minimize the weight ... -
Nonlinear Deflection Analysis for Coupled Tubular Structures
(The American Society of Mechanical Engineers (ASME), 1971)An analysis is presented for determining the large, transverse deflections of tubular structures that are mechanically coupled at discrete locations along their length. The nonlinearities treated ... -
Thermal Buckling and Snapping of a Circular Ring
(The American Society of Mechanical Engineers (ASME), 1971)An analysis is made of the thermal buckling of flat rings and of shallow conical rings which are subjected to an axisymmetric temperature distribution. It is found that flat rings can buckle ... -
An Analysis of Viscoelastic Damping Characteristics of a Simply-Supported Sandwich Beam
(The American Society of Mechanical Engineers (ASME), 1971)An energy method is employed to analyze the damping in the fundamental mode of a simply-supported sandwich beam with viscoelastic core material sandwiched between two elastic metallic layers ... -
A New Method of Screw Strength Calculation
(The American Society of Mechanical Engineers (ASME), 1971)By considering several factors usually neglected, a more realistic picture of screw strength is obtained. These are: thread geometry, combined tensile and shear stresses, and uncertainty in the ... -
Traveling Waves in Rotating Cylindrical Shells
(The American Society of Mechanical Engineers (ASME), 1971)Vibration analysis of long, thin cylindrical shells rotating about their longitudinal axes is presented. It is shown that only traveling waves may be excited in a rotating shell. Furthermore, ... -
Friction-Instability: A New Design Parameter for Brakes
(The American Society of Mechanical Engineers (ASME), 1971)A new design parameter, friction-instability, is defined in this paper. Friction-instability is a variation in the coefficient of friction which may occur at any time during the life of a brake ... -
The Transient Character of the Near-Field Acoustic Radiation From a Cylindrical Diaphragm Excited by Water Hammer Transients
(The American Society of Mechanical Engineers (ASME), 1971)An investigation of the transient character of the near-field acoustic radiation from a water hammer excited, cylindrical diaphragm was conducted. The investigation was principally experimental and ... -
Relationship Between Plane-Strain Ductility and KIc for Various Steels
(The American Society of Mechanical Engineers (ASME), 1971)In most structural steels, the critical plane-strain stress-intensity factor, KIc , which represents the inherent ability of the material to resist crack propagation, increases with increasing ... -
Drilling Riser Stress Measurements
(The American Society of Mechanical Engineers (ASME), 1971)Field measurements of drilling riser stresses during drilling operations have been made. The field-measured stresses are in agreement with those predicted by EPR ’s pseudodynamic riser stress ... -
The Forces on a Cylinder Oscillating Sinusoidally in Water
(The American Society of Mechanical Engineers (ASME), 1971)This investigation deals with the experimental modeling of wave forces on offshore structures. The model chosen is a sinusoidally oscillating cylinder in a body of water otherwise at rest. This ... -
Fatigue-Crack Propagation in Steels of Various Yield Strengths
(The American Society of Mechanical Engineers (ASME), 1971)The useful life of highly constrained welded structures subjected to cyclic loads often depends on the crack-propagation behavior of the material. Thus, to predict the service life of many ... -
Gas Piping Design for High Speed Reciprocating Compressor Units
(The American Society of Mechanical Engineers (ASME), 1971)This paper discusses the problems associated with gas piping designs incorporating acoustic low pass wave filters for high speed reciprocating compression equipment. It develops a procedure where ...