Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 2741-2760 of 7723
-
Discussion: “The Engineer’s Responsibility for Product Safety” (Egerer, Herbert, 1971, ASME J. Eng. Ind., 93, pp. 394–395)
(The American Society of Mechanical Engineers (ASME), 1971) -
Stress Analysis of a Spherical Acrylic Pressure Hull
(The American Society of Mechanical Engineers (ASME), 1971)This study was initiated to: (1) perform an analytical structural analysis on an acrylic pressure hull, (2) compare the analytical results with all available experimental results, and (3) present ... -
Plasma Treatment of Railway Rails to Improve Traction
(The American Society of Mechanical Engineers (ASME), 1971)Plasma torch treatments of track rails to improve locomotive wheel traction were investigated as a potential substitute for rail sanding. Rolling friction tests were conducted under simulated ... -
The NEMO Submersible
(The American Society of Mechanical Engineers (ASME), 1971)The NEMO (Naval Experimental Manned Observatory) is the first transparent-hull submersible capable of operation to depths as great as 600 ft. Subsystems such as pressure hull, life support, ... -
Stress Analysis of Thin Elasto-Plastic Shells
(The American Society of Mechanical Engineers (ASME), 1971)The stress analysis of thin shells with large deflections loaded into the strain hardening range is presented. Plastic strain incompressibility is assumed. The two governing differential equations ... -
Bending of Cylindrical Shells by Initial Parameter Method
(The American Society of Mechanical Engineers (ASME), 1971)The initial parameter method, in the form proposed by V. Z. Vlasov, is presented and extended to the case of symmetric bending of cylindrical shells. It is shown that the method can be used ... -
Stress Resultants and Out-of-Plane Deformations in Stiff Rings Attached to Elastic Cylinders and Subject to Concentrated Loads
(The American Society of Mechanical Engineers (ASME), 1971)Expressions are derived which give the internal loads and deformations of a relatively stiff ring which is mounted on an elastic cylinder. Three basic types of loads acting on the ring are ... -
On Half Harmonics
(The American Society of Mechanical Engineers (ASME), 1971)A study of the pulsations in hydraulic pumps and motors has led to some theorems concerning the nature of half-harmonics, and to certain aspects of design wherein such properties may be exploited. -
Underwater Behavior of Free-Flooded Ceramic Ring Transducers
(The American Society of Mechanical Engineers (ASME), 1971)A numerical method is presented for the study of the underwater behavior of piezoelectric ceramic transducers in the shape of a shell of revolution, which are known as free-flooded ring ... -
Application of a Disorder Measure to Acoustical and Structural Models
(The American Society of Mechanical Engineers (ASME), 1971)The interaction of structures and sound fields frequently involves many degrees of freedom of each participant in a complicated interaction process. In one way or another, statistical or ... -
Design of Rotating Disks With Integral Shafts
(The American Society of Mechanical Engineers (ASME), 1971)This paper presents two-dimensional and three-dimensional procedures for evaluation of stress distribution in rotating disks of nonuniform thickness with integral shafts. The two-dimensional analysis ... -
Time Domain Optimization of a Vibration Absorber
(The American Society of Mechanical Engineers (ASME), 1971)This paper considers two design problems involving the transient vibrations of a dynamic vibration absorber. The design objective of the first problem is to minimize the maximum force transmitted ... -
A Design Oriented Approach to Creep and Plasticity in Finite Element Programs
(The American Society of Mechanical Engineers (ASME), 1971)This paper presents procedures for introducing plasticity and creep into finite element programs. The plasticity method described is intended for the designer who is interested in the stress ... -
Vibration Response and Wave Propagation in Periodic Structures
(The American Society of Mechanical Engineers (ASME), 1971)The vibration response of periodic, beam-like structures has conventionally been studied either by transfer matrix or normal mode methods. The latter method becomes unwieldy if the damping and ... -
Sound and Vibration Transmission Through Panels and Tie Beams Using Statistical Energy Analysis
(The American Society of Mechanical Engineers (ASME), 1971)The transmission of sound and vibration through structures is of interest in many noise control problems, including architectural acoustics, sound transmission through aircraft, spacecraft and ... -
Nonlinear Deformation of a Pressure Diaphragm in Contact With a Piston
(The American Society of Mechanical Engineers (ASME), 1971)The problem of a shallow shell of revolution type diaphragm experiencing large deflections while being in contact with a centrally located piston is solved for some typical cases of ... -
Discussion: “Dimensional Parameters Influencing the Behavior of the Morrison Unsupported Area Seal” (Pick, R. J., and Burns, D. J., 1970, ASME J. Eng. Ind., 92, pp. 755–758)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Stress Analysis of a Spherical Acrylic Pressure Hull” (Snoey, M. R., and Katona, M. G., 1971, ASME J. Eng. Ind., 93, pp. 875–882)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Plasma Treatment of Railway Rails to Improve Traction” (Gifford, F. E., and Yoshino, R. T., 1971, ASME J. Eng. Ind., 93, pp. 867–872)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Application of a Disorder Measure to Acoustical and Structural Models” (Lyon, Richard H., 1971, ASME J. Eng. Ind., 93, pp. 814–817)
(The American Society of Mechanical Engineers (ASME), 1971)