Journal of Pressure Vessel Technology: Recent submissions
Now showing items 4461-4480 of 4506
-
An Approximate Model for an Elastic-Plastic Pipe Element Under Combined Loading
(The American Society of Mechanical Engineers (ASME), 1975)An approximate model for the elastic-plastic analysis of a pipe element under combined loading is developed. The model is obtained by generalizing a limit load solution for combined pressure, ... -
Dynamic Response of an Infinite Beam
(The American Society of Mechanical Engineers (ASME), 1975)Both the exact and an approximate solution for the dynamic response of an infinite Bernoulli-Euler beam under an instantaneously applied, concentrated load are presented in this paper. The exact ... -
Flow-Induced Forces on a Cylinder for Different Wall Confinements at High Reynolds Numbers (3.5×105)<Re<(1.2×106)
(The American Society of Mechanical Engineers (ASME), 1975)The nearness of a cylinder to a wall has an important effect on the flow-induced forces exerted on that cylinder, particularly when the cylinder is relatively large compared to the cross ... -
Discussion: “Mechanical Properties of Cast Carbon Steel in Heavy Sections” (Banks, W. C., Skidmore, K. F., and Schwartzbart, H., 1974, ASME J. Pressure Vessel Technol., 96, pp. 73–80)
(The American Society of Mechanical Engineers (ASME), 1975) -
Guide to Butt Joint Factors Based on Radiographic Examination in Accordance With UW-11 And UW-12 of Section VIII, Division I
(The American Society of Mechanical Engineers (ASME), 1975) -
The 1974 Edition of Section XI, Rules for Inservice Inspection of Nuclear Power Plant Components
(The American Society of Mechanical Engineers (ASME), 1975) -
Analysis of Multiholed Orthotropic Laminated Plates by the Boundary-Point-Least-Squares Method
(The American Society of Mechanical Engineers (ASME), 1975)The paper describes the application of boundary-point-least-squares method (BPLS) for the determination of stresses in multiply connected finite orthotropic plates under plane stress. Series solutions ... -
Discussion: “Simplified Second Stage Creep/Relaxation Analysis of Moderately Complex Spatially Three-Dimensional Piping Systems” (Workman, G. H., and Rodabaugh, E. C., 1974, ASME J. Pressure Vessel Technol., 96, pp. 184–192)
(The American Society of Mechanical Engineers (ASME), 1975) -
Elastoplastic Analysis of Space Framework: Initial Force Schemes
(The American Society of Mechanical Engineers (ASME), 1975)Based upon the Morris and Fenves yield criterion for space frameworks, two initial force schemes are presented to analyze the elastoplastic behavior of space frameworks. One is the initial force ... -
Dynamic Responses of Two Parallel Circular Cylinders in a Liquid
(The American Society of Mechanical Engineers (ASME), 1975)The problem of two parallel circular cylinders vibrating in a liquid is studied analytically. First, the equations of motion including fluid coupling are derived using the added mass concept. ... -
Structural Noncyclic Experimentation for Metallic Components in the ASME Boiler and Pressure Vessel Code
(The American Society of Mechanical Engineers (ASME), 1975) -
Transient Creep Analysis With Finite Deformations
(The American Society of Mechanical Engineers (ASME), 1975)A method for obtaining stresses and displacements under conditions of transient creep is illustrated, with finite deformations taken into account. A mixed variational for mutation due to Sanders, ... -
Incremental Solution Procedure for Nonlinear Structural Dynamics Problems
(The American Society of Mechanical Engineers (ASME), 1975)A general incremental formulation is presented for solving nonlinear structural dynamic problems. The formulation introduces a new term which is not obtained in the usual finite element tangent ... -
Underground Storage Systems for High-Pressure Air and Gases
(The American Society of Mechanical Engineers (ASME), 1975)This paper is a discussion of the safety and cost of underground high-pressure air and gas storage systems based on recent experience with a high-pressure air system installed at Moffett Field, ... -
ASME Boiler and Pressure Vessel Code Short Courses
(The American Society of Mechanical Engineers (ASME), 1975) -
The Origin and Objectives of the Uniform Boiler and Pressure Vessel Laws Society
(The American Society of Mechanical Engineers (ASME), 1975) -
Line-Load Displacements in Orthotropic Cylindrical Shells
(The American Society of Mechanical Engineers (ASME), 1975) -
Elevated Temperature Fatigue Tests and Inelastic Stress Analysis of Bellows
(The American Society of Mechanical Engineers (ASME), 1975)For a multiwalled piping of the elevated temperature helium gas loop or HTR, some kinds of joints are required to absorb the thermal expansion difference between the inner and outer pipes. ... -
The National Board and ASME
(The American Society of Mechanical Engineers (ASME), 1975) -
Energy Approach for Creep-Fatigue Interactions in Metals at High Temperatures
(The American Society of Mechanical Engineers (ASME), 1975)An analysis of the so-called creep-fatigue interactions in a reannealed AISI type 304 stainless steel with and without holdtime at 593 deg C (1100 deg F) is presented with a numerical example. ...