Journal of Pressure Vessel Technology: Recent submissions
Now showing items 4441-4460 of 4506
-
Thermal Shock Testing of Fillet-Type Tube-to-Tubesheet Welds
(The American Society of Mechanical Engineers (ASME), 1976)To prove the inherent integrity of the fillet-type tube-to-tubesheet welds proposed in the initial design of the Intermediate Heat Exchanger for the Liquid Metal Fast Breeder Program Fast Flux ... -
Improved 2 1/4 Cr-1 Mo Pressure Vessel Steel Through Electroslag Remelting
(The American Society of Mechanical Engineers (ASME), 1976)Results of a detailed investigation of the internal quality and mechanical properties of electroslag remelted 2 1/4 percent Cr-1 percent Mo steel are presented. Superiority over air melted-vacuum ... -
An Evaluation of the Material Capabilities of Low Carbon 2 1/4 Cr-1 Mo Steel Forgings
(The American Society of Mechanical Engineers (ASME), 1976)Recent advances in the nuclear power generation field have pointed out the need for ferritic steels which will maintain properties at high operating temperatures for extended periods of time. ... -
Friction Area and Nozzle Area for Valves and Fittings as New All-Purpose Flow Parameters
(The American Society of Mechanical Engineers (ASME), 1976)Friction area is proposed as an improvement over Cv for incompressible flow capacity. Nozzle area, experimentally determined, is proposed as an improvement over other parameters for choked flow ... -
Discussion: “Elastic-Plastic Fracture Toughness: A Comparison of J-Integral and Crack Opening Displacement Characterizations” (Griffis, C. A., 1975, ASME J. Pressure Vessel Technol., 97, pp. 278–283)
(The American Society of Mechanical Engineers (ASME), 1976) -
Code for Concrete Reactor Vessels and Containments
(The American Society of Mechanical Engineers (ASME), 1976) -
Design Philosophy of Pressure Vessels for Service Above 10 ksi (70 MPa)
(The American Society of Mechanical Engineers (ASME), 1976)This paper discusses design criteria for pressure vessels intended for service above 10 ksi (70 MPa). Since the ASME Boiler and Pressure Vessel Code cannot, in a practical sense, be applied ... -
Thrust Balancing Exhaust Fitting for Safety and Relief Valves
(The American Society of Mechanical Engineers (ASME), 1976)A description is given of the stress distribution in an elastically strained standard safety valve installation, followed by a discussion of the problem introduced by settlement and vertical ... -
Discussion: “Steady-State Crack Propagation in Pressurized Pipelines Without Backfill” (Kanninen, M. F., Sampath, S. G., and Popelar, C., 1976, ASME J. Pressure Vessel Technol., 98, pp. 56–65)
(The American Society of Mechanical Engineers (ASME), 1976) -
The Interface Boundary Conditions for Bolted Flanged Connections
(The American Society of Mechanical Engineers (ASME), 1976)In most bolted connections, the unknown interface pressure distribution and the extent of the contact region are essential parameters in any stress analysis. Concerning these parameters, experimental ... -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1975) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Application of Spiral Wound Gaskets for Leak-Tight Joints” (Stevens-Guille, P. D., and Crago, W. A., 1975, ASME J. Pressure Vessel Technol., 97, pp. 29–33)
(The American Society of Mechanical Engineers (ASME), 1975) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1975) -
Attitudes Toward Computer Software and Its Exchange in the Pressure Vessel Industry
(The American Society of Mechanical Engineers (ASME), 1975)A survey of computer software use in the pressure vessel industry was conducted by means of a questionnaire that reached 707 active professionals in the industry. 249 filled-in questionnaires ... -
On Seal Forces in Removable End Closures in Very High Pressure Test Chambers
(The American Society of Mechanical Engineers (ASME), 1975) -
Improved Construction of Multilayer Vessels to Apply the ASME Code Section VIII, Division 2
(The American Society of Mechanical Engineers (ASME), 1975)It has been made possible to design the multilayered vessel by employing stress analysis according to ASME Section VIII, Division 2, using the construction method of reinforcing the flexual ... -
A Report: Subcommittee VIII—Shell and Tube Heat Transfer Equipment Project
(The American Society of Mechanical Engineers (ASME), 1975) -
Application of Spiral Wound Gaskets for Leak-Tight Joints
(The American Society of Mechanical Engineers (ASME), 1975) -
Pressure Vessel Reliability
(The American Society of Mechanical Engineers (ASME), 1975)