Journal of Pressure Vessel Technology: Recent submissions
Now showing items 4421-4440 of 4506
-
Influence of Sulfur Content on the Fracture Toughness Properties of 2 1/4 Percent Cr-1 Percent Mo Steel
(The American Society of Mechanical Engineers (ASME), 1976)The effects of sulfur content on the fracture toughness properties of 2 1/4Cr-1 Mo steel were evaluated at test temperatures above, at, and below the nil ductility transition temperature (NDTT) ... -
On the Dynamic Analysis of Curved and Twisted Cylinders Transporting Fluids
(The American Society of Mechanical Engineers (ASME), 1976)The longitudinal, torsional and 2-transverse equations of motion are formulated for the titled problem through application of Hamilton’s Principle. Curvature-torsion conditions under which linear ... -
Low-Alloy High-Strength Steel for Boiler Tubes (LowC-9Cr-2Mo)
(The American Society of Mechanical Engineers (ASME), 1976)High-strength steel tube HCM9M (LowC-9Cr-2Mo) steel, which shows the intermediate high-temperature strength between austenitic stainless steels and commercial low-alloy steels, has been developed. ... -
Stability of Internally Pressurized Vessels With Ellipsoidal Heads
(The American Society of Mechanical Engineers (ASME), 1976)Cylindrical vessels with 2:1 ellipsoidal heads in the range of radius to thickness ratios from 200 to 5000 were analyzed with a finite element program to determine the internal pressures that ... -
Inelastic Response of Nuclear Piping Subjected to Rupture Forces
(The American Society of Mechanical Engineers (ASME), 1976)A numerical procedure which can be used to evaluate the inelastic dynamic response of piping systems subjected to blow-down forces is described. The following finite elements are used to represent ... -
Mechanical Properties of Roll Extruded Nuclear Reactor Piping
(The American Society of Mechanical Engineers (ASME), 1976)The elevated temperature mechanical properties of large diameter (28 in.) seamless pipe produced by roll extrusion for use as primary piping for sodium coolant in the Fast Flux Test Facility ... -
The Tubular Exchanger Manufacturers Association and Industry
(The American Society of Mechanical Engineers (ASME), 1976) -
On the Interpretation of the Acoustic Emission Signals
(The American Society of Mechanical Engineers (ASME), 1976)The A.E. signals are of nonstationary random type, the nonstationarity being connected with the evolution of the source, whose characterization is here pursued by the development of methodologies ... -
Further Observations on A533-B Steel Plate Tailored for Improved Radiation Embrittlement Resistance
(The American Society of Mechanical Engineers (ASME), 1976)A series of advanced investigations on the radiation performance of four 6-in-thick plates from a large (30-ton) commercial melt of A533-B steel is described. The melt represented the first ... -
A Mathematical Description for the Stress-Strain Behavior of Annealed 2 1/4 Cr-1 Mo Steel
(The American Society of Mechanical Engineers (ASME), 1976)We have conducted a detailed series of tensile tests on one heat of annealed 2 1/4 Cr-1 Mo steel over the range 25 to 593°C (75 to 1100°F) and at nominal strain rates of 0.4, ... -
Elastic-Plastic Analysis of Curved Structures Subjected to Static and Dynamic Loads
(The American Society of Mechanical Engineers (ASME), 1976)A method is presented for the finite-element analysis of curved planar structures consisting of a combination of thin straight and curved beam elements. In the analysis both static and dynamic ... -
Analysis of Fatigue-Crack Growth in a High-Strength Steel—Part II: Variable Amplitude Block Loading Effects
(The American Society of Mechanical Engineers (ASME), 1976)To investigate load sequencing effects in fatigue-crack growth, surface flaw or part-through crack (PTC) specimens of a high-strength pressure vessel steel were subjected to variable-amplitude ... -
Hydrodynamic Inertia Coefficients for a Tube Surrounded by Rigid Tubes
(The American Society of Mechanical Engineers (ASME), 1976)The virtual mass of a long, transversely vibrating tube submerged in a liquid was experimentally determined. The tube was surrounded by rigid tubes in a hexangular array and in square array, ... -
Creep Behavior of SMA Type 316 Weld Metal With Controlled Residual Elements
(The American Society of Mechanical Engineers (ASME), 1976)Type 316 stainless steel filler metal is a candidate material for welds in piping and other components of Liquid Metal Fast Breeder Reactors. There are few elevated-temperature tensile and creep ... -
Erratum: “Elastic-Plastic Analysis of Curved Structures Subjected to Static and Dynamic Loads” (Journal of Pressure Vessel Technology, 1976, 98, pp. 126–134)
(The American Society of Mechanical Engineers (ASME), 1976) -
An Introduction to Section VIII, Division 1 of the ASME Boiler and Pressure Vessel Code
(The American Society of Mechanical Engineers (ASME), 1976)A general introduction to Section VIII, Division 1, primarily from the viewpoint of the designer, is presented. The organization of the different sections of the Code are explained, and the ... -
New Rules for Construction of Section III, Class 1 Components for Elevated Temperature Service
(The American Society of Mechanical Engineers (ASME), 1976) -
Buckling Rules for Nuclear Components—Code Case 1592
(The American Society of Mechanical Engineers (ASME), 1976)The buckling rules for nuclear components in elevated temperature service have been recently modified by the ASME Boiler and Pressure Vessel Code Committee. The specific modifications and some ... -
Elevated Temperature Design—Development and Implementation of Code Case 1592
(The American Society of Mechanical Engineers (ASME), 1976) -
Experimental Stress Analysis of Cylinder-to-Cylinder Shell Models and Comparisons With Theoretical Predictions
(The American Society of Mechanical Engineers (ASME), 1976)Four carefully machined cylinder-to-cylinder shell models were tested, and the experimentally determined stresses were compared with theoretical predictions obtained from a thin-shell finite-element ...