Journal of Engineering for Gas Turbines and Power: Recent submissions
Now showing items 3881-3900 of 9564
-
Discussion: “Laminar Incompressible Flow in the Entrance Region of Ducts of Arbitrary Cross Section” (Miller, James A., 1971, ASME J. Eng. Power, 93, pp. 113–117)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “The Buzz-Saw Noise Generated by a High Duty Transonic Compressor” (Philpot, M. G., 1971, ASME J. Eng. Power, 93, pp. 63–68)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Tailpipe Effects on Gas Turbine Diffuser Performance With Fully Developed Inlet Conditions” (Kelnhofer, William J., and Derick, Charles T., 1971, ASME J. Eng. Power, 93, pp. 57–61)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Acceleration Performance Analysis of a Gas Turbine Destroyer Escort” (Bodnaruk, A., and Rubis, C. J., 1971, ASME J. Eng. Power, 93, pp. 49–55)
(The American Society of Mechanical Engineers (ASME), 1971) -
Development of Cryogenic Heat Pipes
(The American Society of Mechanical Engineers (ASME), 1971)The operation of a LN2 cryogenic heat pipe has been demonstrated experimentally in the range 78 K to 90 K. This heat pipe involves a totally new wick concept, viz., the “parallel capillary ... -
Unbalance Response of an Elastic Rotor in Damped Flexible Bearings at Supercritical Speeds
(The American Society of Mechanical Engineers (ASME), 1971)The unbalance response of a uniform flexible rotor in fluid-film bearings has been analyzed for speeds up to 20 times the lowest rigid-bearing critical speed. Rotor mass and elasticity are ... -
Thermal Cycle Arrangements for Power Plants Employing Dry Cooling Towers
(The American Society of Mechanical Engineers (ASME), 1971)The use of dry cooling towers with air as the cooling medium will become more prevalent in the not-too-distant future as water quantities available for consumption in evaporative cooling processes ... -
Corrosion of Heat-Exchange Tubes in a Simulated Coal-Fired MHD System
(The American Society of Mechanical Engineers (ASME), 1971)An experimental unit was built to burn 125 lb of coal an hour at 4000 deg F in a cyclone burner with oxygen-enriched air preheated to 1500 deg F to ascertain the fireside corrosion problems ... -
2750 Deg F Engine Test of a Transpiration Air-Cooled Turbine
(The American Society of Mechanical Engineers (ASME), 1971)The development of gas turbine engines for advanced subsonic and supersonic aircraft as well as for potential utilization of these high performance engines for stationary and marine applications ... -
Analysis of Changes in the Performance Characteristics of Steam Turbines
(The American Society of Mechanical Engineers (ASME), 1971)The proper analysis of routine steam turbine performance test data can afford valuable information on the internal condition of a steam turbine. This paper outlines the theory behind the analysis ... -
Discussion: “Evaluation of Steam Washers in Power-Plant Boilers” (Klein, H. A., 1961, ASME J. Eng. Power, 83, pp. 343–350)
(The American Society of Mechanical Engineers (ASME), 1961) -
Performance of Air-Cooled Radiatively Heated Screen Matrices
(The American Society of Mechanical Engineers (ASME), 1971)The problem of combined radiation and convection in a porous bed, consisting of randomly stacked wire screens, was experimentally investigated. A collimated radiation source was used for bed ... -
Electrofluid Dynamic Energy Conversion Present Status and Research Areas
(The American Society of Mechanical Engineers (ASME), 1971)This paper presents in depth the major basic performance characteristics of electrofluid dynamic (EFD) energy conversion processes, which are shown to be complementary to magnetofluid dynamic ... -
The Use of Flow Modeling Techniques to Obtain a Minimum Loss Design for the Stack Entrance Section of a 700-ft Power Plant Chimney
(The American Society of Mechanical Engineers (ASME), 1971)Scale model testing and flow visualization techniques were used to achieve substantial reductions in stack entrance total pressure loss levels. This paper presents the loss coefficient results ... -
Computed Performance Characteristics of Electrofluid Dynamic Colloid Generators
(The American Society of Mechanical Engineers (ASME), 1971)The effects of the electric breakdown limitation on the power output of an electrofluid dynamic generator operating with colloids are studied. The study is performed for both an axisymmetric ... -
An Approximate Solution to the Shuttle Heat-Transfer Losses in a Reciprocating Machine
(The American Society of Mechanical Engineers (ASME), 1971)The axial heat transfer due to the oscillatory motion of a long displacer in a cylinder with an axial temperature gradient is treated. The effect of the resistance to heat transfer due to ... -
Thermal Energy Requirements of Air-Conditioning Systems
(The American Society of Mechanical Engineers (ASME), 1971)The thermal energy requirements for air conditioning by compressive and absorption methods were determined for light-water, thermal-breeder, and fast-breeder reactors. The energy required to produce ... -
A Traversing-Thermocouple Technique for the Rapid Measurement of Thermal Conductivity in the Range 300 to 1200 K
(The American Society of Mechanical Engineers (ASME), 1971)A thermal conductivity measurement technique has been developed based on a novel design employing an ultrafine (0.02 cm dia) “traversing” thermocouple. This technique features the rapid determination ... -
Discussion: “Computation of Thermodynamic Properties of Carbon Dioxide in the Range 0–750 Deg C” (Angelino, G., and Macchi, E., 1970, ASME J. Eng. Power, 92, pp. 301–309)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Loss and Flow Path Studies on Centrifugal Compressors Part I and Part II” (Balje, O. E., 1970, ASME J. Eng. Power, 92, pp. 275–300)
(The American Society of Mechanical Engineers (ASME), 1971)