Journal of Engineering for Gas Turbines and Power: Recent submissions
Now showing items 3861-3880 of 9564
-
Vibration Characteristics of Low Aspect Ratio Compressor Blades
(The American Society of Mechanical Engineers (ASME), 1971)This paper presents the results of a study of the vibration characteristics of low aspect ratio compressor blades. The treatment is based on thin shell theory and the Rayleigh-Ritz method is ... -
Effect of Dimensional Parameters of Impellers on Performance Characteristics of a Radial-Inflow Turbine
(The American Society of Mechanical Engineers (ASME), 1971)An experimental radial-inflow turbine having a pressure ratio of 2:1 was constructed, and the effect of dimensional parameters of an impeller was examined by performance tests of the turbine ... -
150 kwe Supercritical Closed Cycle System
(The American Society of Mechanical Engineers (ASME), 1971)This paper explores the potential applicability of the Supercritical (Feher) Thermodynamic Power Cycle to advanced ground nuclear power systems. The supercritical cycle is a closed cycle heat ... -
The Buzz-Saw Noise Generated by a High Duty Transonic Compressor
(The American Society of Mechanical Engineers (ASME), 1971)The buzz-saw noise made by a two-stage transonic research compressor has been investigated experimentally over a range of tip relative Mach numbers up to 1.56. The results show that the ... -
Tailpipe Effects on Gas Turbine Diffuser Performance With Fully Developed Inlet Conditions
(The American Society of Mechanical Engineers (ASME), 1971)Straight-walled diffuser-tailpipe systems with fully developed inlet conditions as encountered with gas turbine exhaust ducting systems have been tested. For constant length diffusers with varying ... -
Acceleration Performance Analysis of a Gas Turbine Destroyer Escort
(The American Society of Mechanical Engineers (ASME), 1971)The dynamic acceleration performance of a single screw destroyer escort driven by two FT4A-2 gas turbine engines through a reversing reduction gear was analyzed. The analysis was carried out ... -
Comparison of Performance of Supersonic Blading in Cascade and in Compressor Rotors
(The American Society of Mechanical Engineers (ASME), 1971)Reduction of engine weight and engine specific fuel consumption is a continuing goa of jet engine designers. An attractive approach is through the development of efficient, high-tip speed ... -
Design and Performance Evaluation of Four Transonic Compressor Rotors
(The American Society of Mechanical Engineers (ASME), 1971)A set of four compressor rotors was designed as a means of optimizing blade camberline shape in the high-transonic Mach number region. One blade row was designed for a tip diffusion factor ... -
Discussion: “Dissimilarity Laws in Centrifugal Pumps and Blowers” (Stepanoff, A. J., and Stahl, H. A., 1961, ASME J. Eng. Power, 83, pp. 381–390)
(The American Society of Mechanical Engineers (ASME), 1961) -
Analysis of a Combined Gas Turbine and Absorption-Refrigeration Cycle
(The American Society of Mechanical Engineers (ASME), 1971)An appreciable improvement in the performance of gas turbines operating with ambient temperatures above 90 deg F could be achieved by combining an absorption-refrigeration unit to the power ... -
Off-Design Performance of Multistage Turbines
(The American Society of Mechanical Engineers (ASME), 1971)Nondimensional equations are developed for the performance of a multistage axial flow turbine operating at conditions which differ from those for which the turbine is designed. The effect of ... -
Thermal Stress and Fatigue Analysis in Turbine Rotors
(The American Society of Mechanical Engineers (ASME), 1971)A method of thermal stress and fatigue analysis under triaxial stress conditions is presented. A rotor of a marine steam turbine is taken as a typical example to illustrate the detailed method ... -
A Model for Flow Distribution in Manifolds
(The American Society of Mechanical Engineers (ASME), 1971)An analytical investigation of the performance of flow distribution systems was conducted for both intake and exhaust manifolds. Primary emphasis was placed on configurations in which the lateral ... -
Semiempirical Criterion of Erosion Threat in Modern Steam Turbines
(The American Society of Mechanical Engineers (ASME), 1971)A parametric relationship is developed for the degree of erosion to be expected in a low-pressure steam turbine stage operating with wet steam. This relationship involves geometrical parameters ... -
Erratum: “An Investigation of Annulus Wall Boundary Layers in Axial Flow Turbomachines” (Journal of Engineering for Power, 1970, 92, pp. 369–376)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Boundary Layer Optimization for the Design of High Turning Axial Flow Compressor Blades” (Papailiou, K. D., 1971, ASME J. Eng. Power, 93, pp. 147–154)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “A Unified Procedure for the Calculation of Off-Design Performance of Radial Turbomachinery” (Davis, R. C., and Dussourd, J. L., 1971, ASME J. Eng. Power, 93, pp. 133–145)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Measured and Predicted Secondary Flows in a Centrifugal Impeller” (Howard, J. H. G., and Lennemann, E., 1971, ASME J. Eng. Power, 93, pp. 126–131)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Inlet Guide Vane Performance of Centrifugal Blowers” (Stepanoff, A. J., 1961, ASME J. Eng. Power, 83, pp. 371–378)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “A Method for Predicting Compressor Cascade Total Pressure Losses When the Inlet Relative Mach Number Is Greater Than Unity” (Balzer, R. L., 1971, ASME J. Eng. Power, 93, pp. 119–124)
(The American Society of Mechanical Engineers (ASME), 1971)