Journal of Engineering Materials and Technology: Recent submissions
Now showing items 3201-3220 of 3257
-
Experimental Determination of Side Boundary Effects on Stress Intensity Factors in Surface Flaws
(The American Society of Mechanical Engineers (ASME), 1975)A technique consisting of stress-freezing photoelasticity coupled with a Taylor Series Expansion of the maximum local in-plane shearing stress known as the Taylor Series Correction Method (TSCM) ... -
Large Deflection of a Different Modulus Circular Plate
(The American Society of Mechanical Engineers (ASME), 1975)It is known that some composite materials or high-polymers behave differently in simple tension and compression. The present paper is concerned with a bending analysis of a different modulus ... -
Effects of Change of Phase on Temperature Distribution Due to a Moving Heat Source
(The American Society of Mechanical Engineers (ASME), 1975)This paper presents a numerical method for the solution of problems of moving heat sources with change of phase and with any boundary condition. Calculated results of two specific cases are ... -
Fatigue Crack Propagation Rates for Duralumin in Simple Bending
(The American Society of Mechanical Engineers (ASME), 1975)Flat sheet stock of 2024-T3 Duralumin was tested for fatigue crack propagation in simple bending. Transcrystalline cracking was observed at a rate proportional to stress intensity factor squared ... -
Stress Relaxation in the Sn-Pb Eutectic Alloy
(The American Society of Mechanical Engineers (ASME), 1975) -
An Evaluation of the 100,000-hr Rupture Ductility of Type 304-Type 304H Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1975) -
High-Temperature Materials in Gas Turbines
(The American Society of Mechanical Engineers (ASME), 1975) -
The Mechanical Behavior of Rapidly Solidified Al-Al2Cu and Al-Al3Ni Eutectics at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1975)The mechanical behavior of semi-continuously cast Al-Al2 Cu and Al-Al3 Ni eutectics has been studied in tension at temperatures between 350–500 deg C (Al-Al2 Cu) and 500–625 deg C (Al-Al3 Ni). ... -
Prediction of the Tensile Properties of Sheet Metal Composites
(The American Society of Mechanical Engineers (ASME), 1975)Sheet metal laminates are becoming more widely used because of advantageous combinations of the properties of their component parts. Theoretical equations have been developed to predict the tensile ... -
Effect of Friction and Specimen Geometry on the Ductile Fracture in Upset Forging
(The American Society of Mechanical Engineers (ASME), 1975)Experiments were conducted to determine the effect of interface friction and specimen geometry on the useful ductile flow limit of 1100 aluminum and 1095 steel at room temperature. The tests ... -
Surface Finishes Produced by Tungsten Carbide Taper Pin Reamers
(The American Society of Mechanical Engineers (ASME), 1975)The surface finishes produced by taper reaming of holes in a composite structure of aluminum alloy and ultra-high strength steel are examined for both dry and lubricated cutting conditions. In ... -
Subsequent Yield Surfaces for Annealed Mild Steel Under Servo-Controlled Strain and Load Histories: Aging, Normality, Convexity, Corners, Bauschinger and Cross Effects
(The American Society of Mechanical Engineers (ASME), 1975)Initial-yield results on SAE 1017 steel are presented for: four different specimens under combined axial load and twisting moment for servo controlled loading; and six different specimens under ... -
A New Parameter for the Hysteretic Stress-Strain Behavior of Metals
(The American Society of Mechanical Engineers (ASME), 1975)Analysis of transient and steady state stress-strain hysteresis behavior of several structural metals reveals a new parameter, defined as the “Yield Range Increment”, which uniquely denotes the ... -
Application of a Forming Limit Concept to the Design of Powder Preforms for Forging
(The American Society of Mechanical Engineers (ASME), 1975)The soundness of the metallurgical structure and the associated strength of a forged powder preform material increase with increasing lateral flow during the forging process. Unconstrained lateral ... -
Simulation of the Heading Process
(The American Society of Mechanical Engineers (ASME), 1975)Plasticine, Commercially Pure Lead and 6061T6 Aluminum have been used as model materials to simulate some of the forming processes that can arise during a first blow axisymmetric heading operation ... -
Warm and Cold Heading of Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1975)A series of warm and cold heading tests ranging from room temperature to 400 deg C have been conducted on 305 and copper bearing 302 stainless steel wires as well as 0.2 percent C steel ... -
The Role of Lubrication in the Cold Heading of Mild Steel
(The American Society of Mechanical Engineers (ASME), 1975)This work provides information leading to the evaluation of the coefficient of friction for various lubricants during the first blow of a double blow heading operation on AISI 1018 steel wire. ... -
The Effect of Strain-Rate Upon the Tensile Deformation of Materials
(The American Society of Mechanical Engineers (ASME), 1975)The tensile strength of seventeen engineering materials including steels, Al alloys, and fiber-reinforced plastics, has been determined at strain-rates from 10−3 to 103 sec−1 . Variable effects ... -
A Consideration on Limits of Cold Working in Nuclear Construction
(The American Society of Mechanical Engineers (ASME), 1975)Cold working of metals affects the mechanical properties of those metals. These effects are particularly important in the design, analysis and subsequent performance of materials used in elevated ... -
Ductility Indices at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1975)Ductility is a property of a material which has been defined by many investigators who have employed a variety of measurements or indices. The purposes of this paper are to describe some of ...