Journal of Engineering Materials and Technology: Recent submissions
Now showing items 3221-3240 of 3257
-
The Double Ligament Tensile Test: Its Development and Application
(The American Society of Mechanical Engineers (ASME), 1975)Determination of yield and ultimate strengths and elongation in three orthogonal directions by means of the double ligament tensile test permits detailed exploration of anisotropy in rolled plate, ... -
Prediction of Temperature Distributions in Axisymmetric Compression and Torsion
(The American Society of Mechanical Engineers (ASME), 1975)Two numerical methods, one for axisymmetric compression and the other for axisymmetric torsion, have been developed to predict nonsteady-state temperature fields in these deformation processes. In ... -
Plastic Energy Required for Fatigue Failure of Specimens Containing Cracks
(The American Society of Mechanical Engineers (ASME), 1975)A study is conducted to determine the plastic energy absorbed by a material subjected to cyclic loading during the crack propagation stage. The analysis is based on Liu’s elastoplastic solution ... -
Effect of Residual Elements on Fracture Characteristics and Creep Ductility of Type 308 Stainless Steel Weld Metal
(The American Society of Mechanical Engineers (ASME), 1975)Previous studies had shown that conventional type 308 stainless steel weld metal can have low creep ductility (< 1 percent total elongation) at 650 deg C. This paper demonstrates that the ... -
On the Speeds of Instability of a Rotating Hollow, Anisotropic Cylinder
(The American Society of Mechanical Engineers (ASME), 1975)Hill’s theory of plastic anisotropy is used to investigate the effect of the parameters of anisotropy on the speeds at which long, hollow cylinders rotating about their longitudinal axes reach ... -
Flexural Stiffness of Sandwich Beams
(The American Society of Mechanical Engineers (ASME), 1975)Two new theories have been developed for predicting the bending stiffness of sandwich beams. The first theory applies to the general case of any combination of skin and core while the second, ... -
Determination of Dewetting Criterion for Nonlinear Solid Propellant Stress Analysis
(The American Society of Mechanical Engineers (ASME), 1975)A criterion for dewetting in solid propellant materials is developed from an application of Drucker’s postulate to an idealized model of stress-strain behavior. The criterion is evaluated ... -
Influence of Specimen Features on the Strength of Boron/Epoxy-Reinforced Metal
(The American Society of Mechanical Engineers (ASME), 1975) -
Differential Testing and the Evaluation of Thermal Activation Parameters
(The American Society of Mechanical Engineers (ASME), 1975)Thermally activated mechanisms of dislocation motion and interaction account for the dependence of stress on strain, temperature, and time during plastic deformation. Much of the recent activity ... -
Creep-Rupture Properties, Resistance to Temper Embrittlement and to Attack by Hydrogen of a 1.4 Percent Mn — 0.25 Percent Mo — 0.03 Percent Cb Steel
(The American Society of Mechanical Engineers (ASME), 1975)A laboratory heat of an improved boiler steel containing 0.13 percent C, 1.36 percent Mn, 0.27 percent Mo, 0.03 percent Cb, and 0.010 percent N was prepared; creep-rupture properties, resistance ... -
Ultimate Strength Versus Material Constant
(The American Society of Mechanical Engineers (ASME), 1975) -
On the Correlation Between Friction-Coefficients and Adhesion Stresses
(The American Society of Mechanical Engineers (ASME), 1975) -
Stress-Corrosion Cracking
(The American Society of Mechanical Engineers (ASME), 1975) -
The Metal Properties Council, Inc. Today
(The American Society of Mechanical Engineers (ASME), 1975) -
Representation of the High-Temperature Tensile Behavior of Reannealed Type 304 Stainless Steel by the Voce Equation
(The American Society of Mechanical Engineers (ASME), 1975)Tensile tests were performed on a reference heat of type 304 stainless steel (heat 9T2796) in the laboratory reannealed condition. Testing temperatures ranged from 25 to 760 deg C (77 to 1400 ... -
Fractographic Analysis of Fatigue Failures
(The American Society of Mechanical Engineers (ASME), 1975)Although fractography is usually applied to basic research, it can also be used in studies of machine components which have failed in service or in testing. This paper discusses fractographic ... -
Predictions of the Effect of Yield Strength on Fatigue Crack Growth Retardation in HP-9Ni-4Co-30C Steel
(The American Society of Mechanical Engineers (ASME), 1975)Baseline mechanical property data, constant amplitude fatigue crack growth rate data, and single-peak overload test data are presented for HP-9Ni-4Co-30C steel heat treated to three strength levels. ... -
A Description of Crack Growth From Defects Under Creep Conditions
(The American Society of Mechanical Engineers (ASME), 1975)Methods previously used to describe crack growth under creep conditions are reviewed. Under some conditions, materials can be notch insensitive and a model is developed based on engineering ... -
Deformation Characteristics and Time-Dependent Notch Sensitivity of Udimet 700 at Intermediate Temperatures
(The American Society of Mechanical Engineers (ASME), 1975)Time-dependent notch sensitivity of Udimet 700 sheet, bar, and investment castings was observed between 1000 deg and 1400 deg F (538–760 deg C) but not at 1600 deg F (871 deg C). As was ... -
Failure in Two Fire Extinguishers
(The American Society of Mechanical Engineers (ASME), 1975)Failures of two fire extinguishers are examined in this paper detailing circumstances, laboratory examination, and analysis of failure. Both failures resulted in serious injury to the individual ...