Journal of Engineering Materials and Technology: Recent submissions
Now showing items 3241-3257 of 3257
-
“In Vivo” Determination of Macroscopic Biological Material Properties
(The American Society of Mechanical Engineers (ASME), 1975)This paper describes an experimental-analytical technique for determining the in-vivo macroscopic biological material properties of the human forearm. The technique utilizes the experimentally ... -
Static and Dynamic Collapse Characteristics of Scale Model Corrugated Tubular Sections
(The American Society of Mechanical Engineers (ASME), 1975)The collapse load of a series of scale model, corrugated tubular sections was determined, both by quasi-static and by dynamic testing. Provided that the material from which the models are made ... -
Optimum Design for a Corrugated Diaphragm Clamped to a Shaft Undergoing Axial or Angular Displacement
(The American Society of Mechanical Engineers (ASME), 1975)The bending of a circular corrugated diaphragm which is clamped along its outer edge and clamped to a shaft at its geometric center is analyzed. The shaft may undergo small axial displacements ... -
Strain-Hardening Characteristics of Ti-6Al-2Sn-4Zr-2Mo Alloy
(The American Society of Mechanical Engineers (ASME), 1975)The strain-hardening exponent (n) is considered to be numerically equal to the uniform plastic strain for materials which exhibit a power low true stress true strain relation. In Ti-6Al-2Sn-4Zr-2Mo ... -
Engineering Materials and Technology: Retrospect and Prospect
(The American Society of Mechanical Engineers (ASME), 1975) -
NSF Workshop on Inelastic Constitutive Equations for Metals: Experimentation-Computation-Representation
(The American Society of Mechanical Engineers (ASME), 1975) -
Mechanical Properties of Several Products From a Single Heat of Type 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1975)Tensile and stress-rupture tests were run on several products from a 90-ton (8.2 × 104 Kg) heat of type 304 stainless steel. The yield stress of the products in the as-received condition ... -
Fatigue-Crack Growth in an X-65 Line-Pipe Steel at Low Cyclic Frequencies in Aqueous Environments
(The American Society of Mechanical Engineers (ASME), 1975)The effects of salt and distilled water environments on fatigue-crack growth rates have been evaluated for an X-65 line-pipe steel. Tests were conducted over a frequency range between 10 and ... -
The Effect of Varying Degrees of Cold Work on the Stress-Rupture Properties of Type 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1975)Cold work enhances the room temperature tensile properties of austenitic stainless steels. There are few data on the effect of varying degrees of cold work on elevated temperature properties. ... -
A Constitutive Equation for High Temperature Flow
(The American Society of Mechanical Engineers (ASME), 1975)A constitutive equation which describes the behavior of strain rate sensitive materials which do not strain harden significantly is often required in the solution of various problems involving ... -
A Case History of Cracking Failures in Deformed Austenitic Alloy Pipe Operating in the Temperature Range of 1000-1300 Deg F (538-705 Deg C)
(The American Society of Mechanical Engineers (ASME), 1975)The results of several cracking failures in fabricated austenitic alloy pipe are reported in detail. These failures were a result of cracking which occurred at the operating temperature in zones ... -
Fracture Toughness Phenomena in an Unaged Beta Titanium Alloy
(The American Society of Mechanical Engineers (ASME), 1975)The fracture toughness behavior of a commercial beta titanium alloy, Ti-3Al-8V-6Cr-4Zr-4Mo, has been examined between −196°C and 380°C, The observed tough-brittle transition results from ... -
Test Methods for Fuel Oil Ash Corrosion of Heat Resisting Alloys
(The American Society of Mechanical Engineers (ASME), 1975)A cooperative study has been performed by twenty members of the Committee on Heat Resisting Metals and Alloys of Japan Society for the Promotion of Science to find a useful rapid test method ... -
Effects of Cold Work and Mechanical Equation of State in 1100 Aluminum Alloy
(The American Society of Mechanical Engineers (ASME), 1975)The concept of mechanical equation of state is reviewed based on experimental results on 1100 aluminum alloy. It is applied to describe the effects of cold work on creep and creep rupture ... -
The Development of Fatigue Crack Propagation Models for Engineering Applications at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1975)The value of modelling the fatigue crack propagation process is discussed and current models are examined in the light of increasing knowledge of crack tip deformation. Elevated temperature ... -
Letter to the Editor commenting on “Effect of Friction and Specimen Geometry on the Ductile Fracture in Upset Forging” (Samanta, S. K., 1975, ASME J. Eng. Mater. Technol., 97, pp. 14–20)
(The American Society of Mechanical Engineers (ASME), 1975) -
A Report on the International Conference on Composite Materials/1975 (ICCM/75)
(The American Society of Mechanical Engineers (ASME), 1975)