Journal of Engineering Materials and Technology: Recent submissions
Now showing items 3181-3200 of 3257
-
Analysis of Deep-Drawing Over a Tractrix Die
(The American Society of Mechanical Engineers (ASME), 1976)An analysis is given of the deep-drawing of a circular blank into a cylindrical shell over a tractrix die. Comparison is made between the theoretical and the experimental results of the drawing ... -
An Exponential Stress-Strain Law for Cyclic Plasticity
(The American Society of Mechanical Engineers (ASME), 1976)A previously proposed nonlinear differential constitutive equation for creep-plasticity interaction under a uniaxial state of stress is specialized for the time independent case. The characteristics ... -
Rotating Bending Fatigue Tests in a Hydrostatic Environment
(The American Society of Mechanical Engineers (ASME), 1976) -
Estimation of Fatigue Limit of Steel Subjected to Bending Loads
(The American Society of Mechanical Engineers (ASME), 1976)A method of estimating the fatigue limit of polished steel specimens subjected to bending loads, in terms of brinell hardness number for values of stress ratios other than (−1) and mean ... -
Mechanism of Underclad Cracking—Combined Effects of Residual Strain and Heat-Affected Zone Ductility
(The American Society of Mechanical Engineers (ASME), 1976)The mechanism of heat-affected zone cracking under weld overlay cladding has been investigated for four kinds of ferritic steel overlay-welded with austenitic stainless steel. Cracking occurs ... -
Finite Elastic Deformation of an Annular Rotating Disk
(The American Society of Mechanical Engineers (ASME), 1976)An accurate approximate method for the solution of the generalized plane stress problem of finite elastic deformation of a rotating annular disk is given. The method is applicable to both ... -
Metal Flow and Fracture in an Extrusion-Forging Process
(The American Society of Mechanical Engineers (ASME), 1976)A study was conducted of the metal flow and fracture in a forging process involving both extrusion flow into a hub and lateral flow into a flange. In the initial stage of deformation, ... -
Utility of Surface-Flawed Tensile Bars in Cyclic Life Studies
(The American Society of Mechanical Engineers (ASME), 1976)Surface-flawed tensile bar specimens were developed and tested to investigate the applicability of fracture mechanics to relatively small crack sizes under varying stress-time-temperature conditions ... -
High Strain Rate Tensile Properties of Annealed 2 1/4 Cr-1 Mo Steel
(The American Society of Mechanical Engineers (ASME), 1976)The high strain rate tensile properties of annealed 2 1/4 Cr-1 Mo steel were determined and the tensile behavior from 25 to 566°C and strain rates of 2.67 × 10−6 to 144/s were ... -
A Cumulative Damage Rule Based on the Knee Point of the S-N Curve
(The American Society of Mechanical Engineers (ASME), 1976)Making use of a set of isodamage lines, a fresh concept for predicting the fatigue life, under variable amplitude loading, is presented. It is assumed that all isodamage lines converge at the ... -
Shear Difference Method and Application in Orthotropic Photoelasticity
(The American Society of Mechanical Engineers (ASME), 1976)The shear difference method is developed here for application to orthotropic photoelasticity problems. The two-dimensional stress-optic law which was presented in another paper is used. The ... -
Tensile Properties of Thermally Exposed Type 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1976)The influence of thermal exposure at 800, 1000, and 1200°F (427, 538 and 649°C) on the tensile properties of type 304 stainless steel has been experimentally determined. Specimens were ... -
Fully Plastic Solutions and Large Scale Yielding Estimates for Plane Stress Crack Problems
(The American Society of Mechanical Engineers (ASME), 1976)Fully plastic plane stress solutions are given for a center-cracked strip in tension and an edge-cracked strip in pure bending. In the fully plastic formulation the material is characterized ... -
Fracture Mechanics and Fractography of Creep and Fatigue Crack Propagation at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1976)A fracture mechanics and fractographic study was conducted on creep and fatigue crack propagation of a 304 stainless steel under constant and repeated tensile stress at a temperature of 650°C. ... -
Flow Stresses in Sheet Material Formed Into Nearly Spherical Shapes
(The American Society of Mechanical Engineers (ASME), 1975)The relationship between the geometry and the membrane stresses of a thin shell under internal or external pressure is analyzed through the concept of prolateness. Prolateness is a quantitative ... -
Formability of Aluminum Alloy Sheets
(The American Society of Mechanical Engineers (ASME), 1975)High strength-to-weight ratio materials are becoming of increasing importance in the automotive industry. Some aluminum alloy sheets offer strength equivalent to low-carbon sheet steel at one third ... -
Influence of the Application of Quick Thermal Welding Cycles in the Toughness of Carbon Steels Susceptible to Aging
(The American Society of Mechanical Engineers (ASME), 1975)A number of cases of brittle fracture in welded structures can be explained by an accelerated aging resulting from the use of welding thermal cycles on strain-hardened steels. This paper ... -
Analysis of Thermal Stresses and Metal Movement During Welding—Part I: Analytical Study
(The American Society of Mechanical Engineers (ASME), 1975)This is the first part of a study of thermal stresses and metal movement during welding. This part discusses analysis of two-dimensional thermal stresses and metal movement during bead-on-plate ... -
Analysis of Thermal Stresses and Metal Movement During Welding—Part II: Comparison of Experimental Data and Analytical Results
(The American Society of Mechanical Engineers (ASME), 1975)This is the second part of a study of thermal stresses and metal movement during welding. Part I described the finite-element analysis of two-dimensional thermal stresses and metal movement ... -
Electronic Recording of Length Changes of a Wire During Dynamic Torsion
(The American Society of Mechanical Engineers (ASME), 1975)