Now showing items 2901-2920 of 3257

    • The Role of Three-Dimensional Effects in Constant Amplitude Fatigue Crack Growth Testing 

      J. J. McGowan; H. W. Liu (The American Society of Mechanical Engineers (ASME), 1980)
      An accurate knowledge of the dependence of the fatigue crack growth rate (da/dN) on the stress intensity factor range (ΔK) is necessary to perform a safety analysis of any structure. Fatigue ...
    • Creep Crack Growth Under LEFM Conditions 

      R. Pilkington; E. Smith (The American Society of Mechanical Engineers (ASME), 1980)
      The paper presents an outline model for creep crack growth under LEFM conditions. The incremental nature of the crack propagation process is taken into account, and a theoretical analysis shows ...
    • Effect of Prestrain at Elevated Temperature on Ductile Fracture of High Strength Steel 

      Y. Mutoh; M. Toyoda; K. Satoh (The American Society of Mechanical Engineers (ASME), 1980)
      The processes of ductile fracture of KD32 steel specimens subjected to prestrain at elevated temperature are observed. Although several large voids are observed at a relatively small strain ...
    • A Comparative Study of Two State-Variable Constitutive Theories 

      T. J. Delph (The American Society of Mechanical Engineers (ASME), 1980)
      Direct quantitative comparisons are drawn between the predictions of two state-variable constitutive theories, that of Hart and a recently-proposed theory due to Robinson, for a number of simple ...
    • Effect of Temperature on Creep Crack Growth 

      V. M. Radhakrishnan; A. J. McEvily (The American Society of Mechanical Engineers (ASME), 1980)
      Investigations have been carried out to study the effect of temperature on crack growth under creep condition in 6061 Al alloy. A parameter approach, connecting the three variables - crack ...
    • Reactor Surveillance Test and Fracture Mechanics Evaluation of Irradiation Embrittlement in Reactor Pressure Vessel Steels 

      Hideaki Takahashi; Kiyoshi Saito; Tetsuo Shoji; Kazuhiro Date; Masahiko Suzuki (The American Society of Mechanical Engineers (ASME), 1980)
      With special reference to a nuclear reactor surveillance test, a new evaluation procedure for the fracture toughness from Charpy Vee-notch data is developed. This procedure utilizes a ...
    • Nondestructive Evaluation of Materials 

      John J. Burke; M. R. James; Volker Weiss (The American Society of Mechanical Engineers (ASME), 1980)
    • Editorial 

      J. N. Kass (The American Society of Mechanical Engineers (ASME), 1979)
    • 50-Fold Difference in Region-II Fatigue Crack Propagation Resistance of Titanium Alloys: A Grain-Size Effect 

      G. R. Yoder; L. A. Cooley; T. W. Crooker (The American Society of Mechanical Engineers (ASME), 1979)
      Fatigue crack growth rates (da/dN) in ambient laboratory air have been determined for a wide variety of materials from four basic α + β titanium alloy systems. Each material was cyclically ...
    • The Strain-Rate and Temperature Dependence of 18Ni(350) Maraging Steel Tensile Properties 

      H. J. Rack; S. Beitscher; David Kalish (The American Society of Mechanical Engineers (ASME), 1979)
      The influence of microstructure, strain rate, and test temperature on the tensile properties of 18Ni(350) maraging steel was examined. The strain-rate and temperature dependence of the yield ...
    • Producing a Tough, High Strength Cast Steel Free of Temper Embrittlement 

      S. Floreen (The American Society of Mechanical Engineers (ASME), 1979)
      Temper embrittlement of a cast 3Ni-3Cr steel was produced by small amounts of either P or Mn in samples tempered at 650°C and air cooled. Auger spectroscopy examinations showed P embrittlement ...
    • Analysis of Misalignment in the Tension Test 

      Han C. Wu; D. R. Rummler (The American Society of Mechanical Engineers (ASME), 1979)
      Many experimenters fail to appreciate the significance of test system alignment during a tensile test. Poor alignment can increase data scatter and significantly influence some of the test ...
    • Use of Fracture Mechanics Methods for Establishing Inspection Level for Turbine Wheels 

      R. E. Frishmuth (The American Society of Mechanical Engineers (ASME), 1979)
      The establishment of inspection criteria for wheels in rotating machinery is frequently a complex issue. On one hand, safety and reliability of the parts and equipment must be assured while ...
    • A Fracture Surface Rotation Mechanism for Fatigue Tested 2219-T87 Aluminum Sheet 

      G. F. Pittinato (The American Society of Mechanical Engineers (ASME), 1979)
      Fatigue crack propagation tests were conducted on 2219-T87 aluminum sheet to identify the factors that control the rate of fracture surface rotation. Center-cracked, axial loaded specimens were ...
    • Fatigue Crack Growth Model for Part-Through Flaws in Plates and Pipes 

      P. K. Nair (The American Society of Mechanical Engineers (ASME), 1979)
      A fatigue crack growth model is developed to evaluate the behavior of planar elliptic flaws in structural components under cyclic loadings. The model is applied to plates with cyclic tensile ...
    • Reliability as a Materials Property 

      A. A. Bondi (The American Society of Mechanical Engineers (ASME), 1979)
      The introduction of new materials for use in load-bearing applications in a marketplace with very high standards of reliability poses an important design problem because designers had come to ...
    • Residual Fatigue Life Determination of Anchor Bolts 

      B. Mukherjee (The American Society of Mechanical Engineers (ASME), 1979)
      A project was conducted to determine residual fatigue life of transmission tower anchor bolts. Notched and fatigue precracked round bar specimens were used to simulate anchor bolt fatigue and ...
    • The Influence of Cure Time Restrictions on Minimum-Weight Design of Double-Layer SMC Panels 

      M. R. Barone; D. A. Caulk; D. C. Chang (The American Society of Mechanical Engineers (ASME), 1979)
      In this paper, minimum-weight design of double-layer panels made from sheet molding compound is related to cure time—a critical indicator of manufacturing cost. This is done by incorporating ...
    • Fatigue Crack Propagation of Short Cracks 

      M. H. El Haddad; K. N. Smith; T. H. Topper (The American Society of Mechanical Engineers (ASME), 1979)
      Previous studies have shown that both threshold stress intensity factors and fatigue crack growth rates are dependent on crack size. The average growth rates for very short cracks considerably ...
    • Interlaminar Crack Growth in Fiber Reinforced Composites During Fatigue 

      S. S. Wang; H. T. Wang (The American Society of Mechanical Engineers (ASME), 1979)
      This paper presents an investigation of interlaminar crack growth behavior in fiber-reinforced composites subjected to fatigue loading. In the experimental phase of the study, interlaminar crack ...