Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2881-2900 of 3257
-
Fatigue-Crack Growth Behavior in Fast-Neutron-Irradiated Ferritic Steels and Weldments
(The American Society of Mechanical Engineers (ASME), 1980) -
On the Use of Side-Grooves in Estimating JIc Fracture Toughness With Charpy-Size Specimens
(The American Society of Mechanical Engineers (ASME), 1980)The problem of obtaining a meaningful value of toughness from small Charpy-size surveillance specimens, tested at temperature corresponding to the upper shelf where ductile fracture predominates, ... -
Vibratory Stress Relief: A Fundamental Study of Its Effectiveness
(The American Society of Mechanical Engineers (ASME), 1980)Techniques have been devised for inducing consistent residual stress distributions into cantilever beams and for measuring their variation through the section. Commercial vibratory stress relief ... -
Fatigue Crack Growth Response Following a High-Load Excursion in 2219-T851 Aluminum Alloy
(The American Society of Mechanical Engineers (ASME), 1980)To develop further phenomenological understanding of load interaction effects in fatigue, examinations of the influences of stress intensity (K) level, plate thickness and chemical environment on ... -
A Probabilistic Approach to Fatigue Crack Growth Rate
(The American Society of Mechanical Engineers (ASME), 1980)A probabilistic model for fatigue crack growth proposed by K. P. Oh is modified in some respects. Under more natural assumptions than Oh’s it is derived that the rate of fatigue crack growth ... -
The Fatigue and Toughness Properties of a C-Mn-Cb Plate Steel
(The American Society of Mechanical Engineers (ASME), 1980)The fatigue and toughness properties of a C-Mn-Cb plate steel, described both by ASTM A633C and A737B, are presented and compared to the properties of A516-70. Production plate steels made by ... -
Near-Threshold Fatigue Crack Growth in 2 1/4 Cr-1Mo Pressure Vessel Steel in Air and Hydrogen
(The American Society of Mechanical Engineers (ASME), 1980)As part of an ongoing program to examine subcritical flaw growth in candidate steels for proposed coal gasifier pressure vessels, an initial study is made of characteristics of ultralow growth ... -
Void Nucleation Effects in Biaxially Stretched Sheets
(The American Society of Mechanical Engineers (ASME), 1980)The effects of void nucleation occurring during the deformation history on forming limit curves are considered for both in-plane and punch stretching employing a constitutive model of a porous ... -
Fracture Mode Transitions in Aged Ultra-High Strength 18Ni (350) Maraging Steel
(The American Society of Mechanical Engineers (ASME), 1980)The influence of test temperature on the blunt notch and precracked fracture toughness behavior of aged 18Ni (350) maraging steel has been examined. Both toughness measurements exhibit a decrease ... -
Macroscopic Brittle Fracture Criterion Under Multiaxial Stresses
(The American Society of Mechanical Engineers (ASME), 1980)On the basis of traditional fracture criteria and numerous data on the fracture under multiaxial stresses, we propose a new macroscopic criterion for brittle fracture in the state where in ... -
Large Strain, High Strain Rate Testing of Copper
(The American Society of Mechanical Engineers (ASME), 1980)This paper describes the development of a high-speed torsional testing machine and results obtained on the strain-rate dependent strength of copper at large shear strains. Test techniques and ... -
Erratum: “Modelling of Cyclic Plasticity with Unified Constitutive Equations: Improvements in Simulating Normal and Anomalous Bauschinger Effects” (ASME Journal of Engineering Materials and Technology, 1980, 102, pp. 215–222)
(The American Society of Mechanical Engineers (ASME), 1980) -
Some Thoughts Concerning the Existence or Otherwise of an Isotropic Bimodulus Material
(The American Society of Mechanical Engineers (ASME), 1980) -
Brittle Fracture of a Steel Heat Exchanger Shell: A Case History
(The American Society of Mechanical Engineers (ASME), 1980) -
Structural Dynamics: Theory and Computation
(The American Society of Mechanical Engineers (ASME), 1980) -
Roll Deformation in Cold Strip Rolling
(The American Society of Mechanical Engineers (ASME), 1980) -
An Analysis of Wrinkling in the Swift Cup Test
(The American Society of Mechanical Engineers (ASME), 1980)The onset of flange wrinkling in the Swift cup test is analyzed as a plastic bifurcation problem. The flange is modelled as an annular plate made of an orthotropic elastic-plastic material ... -
Cyclic Behavior of Turbine Disk Alloys at 650°C
(The American Society of Mechanical Engineers (ASME), 1980)Five gas turbine disk alloys representing a range of strengths and processing methods were tested for resistance to both cyclic crack initiation and propagation at 650° C using a 0.33 Hz ... -
The Effects of Composition and Microstructure on Temper Embrittlement in 2 1/4 Cr-1 Mo Steel
(The American Society of Mechanical Engineers (ASME), 1980)Temper embrittlement was studied using laboratory heats of 2 1/4 Cr-1 Mo steel of a specified hardness and grain size. Particular amounts of P, Sn, Sb, Mn, and Si were added in various ... -
Delayed Retardation of Overloading Effects in Impression Fatigue
(The American Society of Mechanical Engineers (ASME), 1980)Delayed retardation of plastic zone propagation in impression fatigue caused by a single peak overload is reported together with the effects of overload amplitude and the number of cycles as ...