Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2921-2940 of 3257
-
A Description of History Dependent Plastic Flow Behavior of Anisotropic Metals
(The American Society of Mechanical Engineers (ASME), 1979)An analytical model that describes the loading-history-dependent hardening behavior of anisotropic metals is presented. The proposed hardening model assumes that the rate of change of primary ... -
Shuji Taira: 1920-1978
(The American Society of Mechanical Engineers (ASME), 1979) -
Dynamic Fracture Initiation: A Comparison of Two Experimental Methods
(The American Society of Mechanical Engineers (ASME), 1979)This paper presents a comparison of dynamic fracture initiation results obtained from two independent experimental methods: (1) the instrumented version of the precracked Charpy test and (2) a ... -
Application of J-Integral to High-Temperature Crack Propagation: Part II—Fatigue Crack Propagation
(The American Society of Mechanical Engineers (ASME), 1979)On the basis of the successful results of our previous study on a J-integral approach to the creep crack propagation of steels, the applicability of the creep J-integral to the time dependent ... -
Discussion: “Fatigue Crack Growth Model for Part-Through Flaws in Plates and Pipes” (Nair, P. K., 1979, ASME J. Eng. Mater. Technol., 101, pp. 53–58)
(The American Society of Mechanical Engineers (ASME), 1979) -
Application of J-Integral to High-Temperature Crack Propagation: Part I—Creep Crack Propagation
(The American Society of Mechanical Engineers (ASME), 1979)Crack propagation tests in creep were carried out on 0.16 percent carbon steel at 400 and 500°C in air and at 400°C in vacuum, on Type 316 stainless steel at 600 and 650°C ... -
Inexpensive Reliable Composites—WAM ’78
(The American Society of Mechanical Engineers (ASME), 1979) -
Effect of Metal Composition on Carburizing of Steels
(The American Society of Mechanical Engineers (ASME), 1979)The effect of metal composition on the diffusivity of carbon during carburizing several commercial steels has been investigated using electron probe microanalysis as well as hardness measurements ... -
Part-Elliptical Cracks Emanating From Open and Loaded Holes in Plates
(The American Society of Mechanical Engineers (ASME), 1979)A linear elastic analysis using the finite element-alternating method is conducted for problems of single semi-elliptical and double quarter-elliptical cracks near fastener holes. Mode-one stress ... -
Use of Forming Limit Criteria in Forging Complex Shapes From Metal-Matrix Composites
(The American Society of Mechanical Engineers (ASME), 1979)Fundamental deformation and fracture behavior of fiber-reinforced metal-matrix composites under deformation processing conditions were determined using upset tests on rectangular specimens. Defects ... -
Best Paper Award: Dr. R. O. Ritchie
(The American Society of Mechanical Engineers (ASME), 1979) -
Influence of Microstructural Inhomogeneity on the Formability and Fracture of a Carbon Steel
(The American Society of Mechanical Engineers (ASME), 1979)The dependence of drawability in carbon steel on the grain size shows that a finer grain size is desirable for the better production. On the other hand, the characteristics of fracture in ... -
Materials Problems Experienced at the Synthane Coal-Gasification Pilot Plant
(The American Society of Mechanical Engineers (ASME), 1979)Some failure experiences with metallic components at the Synthane coal-gasification pilot plant are presented. In some cases, corrosion caused by a sulfur environment was a major factor in the ... -
The Statistical Nature of Fatigue Crack Propagation
(The American Society of Mechanical Engineers (ASME), 1979)A statistical investigation of the fatigue crack propagation process was conducted. Sixty-eight replicate constant amplitude crack propagation tests were conducted on 2024-T3 aluminum alloy. From ... -
The Influence of Impurity-Defect Interactions on Radiation Hardening and Embrittlement
(The American Society of Mechanical Engineers (ASME), 1979)It has been established that copper and other trace elements have a detrimental effect on the notch-impact properties of ferritic pressure vessel steels irradiated at reactor operating temperatures ... -
Computed Dynamic Compaction of a Two-Layered Copper Powder Medium
(The American Society of Mechanical Engineers (ASME), 1979)In the paper presented a dynamic compaction of a two-layered powder medium is analyzed. A two-layered medium is used because it is the simplest form of layered medium available. The layers ... -
A Study of Cold Strip Rolling
(The American Society of Mechanical Engineers (ASME), 1979)The effect of roll deformation on separating forces in cold strip rolling is studied. The deformed roll shape is determined by a two dimensional finite element routine. The results are then ... -
A Study of Multiple Hole Extrusion
(The American Society of Mechanical Engineers (ASME), 1979)Two mathematical models proposed by Avitzur and valid for axially symmetrical square extrusion are tested for their ability to predict the maximum power required in single as well as multiple ... -
Diametral Compressive Testing Method
(The American Society of Mechanical Engineers (ASME), 1979)A new approach of diametral compressive testing with circular anvils is proposed. The circular anvils are used to select a suitable contact width or to avoid the collapse of the specimen in ... -
The Influence of Inclusions on the Toughness and Fatigue Properties of A516-70 Steel
(The American Society of Mechanical Engineers (ASME), 1979)The influence of inclusions on the tensile ductility, upper shelf Charpy-V-notch, dynamic tear and J-integral fracture toughness and the fatigue crack propagation behavior and the fatigue endurance ...