Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2561-2580 of 3257
-
Application of Fracture Mechanics to Materials and Structures
(The American Society of Mechanical Engineers (ASME), 1985) -
A Constitutive Model for High Elongation Elastic Materials
(The American Society of Mechanical Engineers (ASME), 1985)Recent advances in computer based structural analysis have in turn led to increased demands for models that can accurately represent material stress-strain behavior. The constitutive representation ... -
Inelastic Behavior of Type 316 Stainless Steel Under Multiaxial Nonproportional Cyclic Stressings at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1985)The stress-range and path-shape dependencies of multiaxial nonproportional cyclic hardening were studied for annealed type 316 stainless steel at 600°C by means of stress controlled tests. ... -
Flow Stress Equations for Type 304 Stainless and AISI 1055 Steels
(The American Society of Mechanical Engineers (ASME), 1985)A model for stress-strain behavior under hot working conditions has been proposed. Based on experimental data, equations for the dependence of flow stress on strain, strain rate, and temperature ... -
Powder Surface Area and Porosity, 2nd Edition
(The American Society of Mechanical Engineers (ASME), 1985) -
Discussion: “A Constitutive Model for High Elongation Elastic Materials” (Swanson, S. R., 1985, ASME J. Eng. Mater. Technol., 107, pp. 110–114)
(The American Society of Mechanical Engineers (ASME), 1985) -
Effect of Tensile-Mean-Strain on Plastic Strain Energy and Cyclic Response
(The American Society of Mechanical Engineers (ASME), 1985)Tests have been conducted to determine the effect of tensile-mean-strain on cyclic properties, low cycle fatigue, and total absorbed plastic strain energy to failure of ASTM A-516 Grade 70 ... -
Optimal Discretization of Power Stress-Strain Law Curves
(The American Society of Mechanical Engineers (ASME), 1985)A criterion for optimal discretization of power stress-strain law curves is proposed. The criterion is based on the assumption that it is desirable to have the fewest possible line segments ... -
Constraint Effect in Thermo-Mechanical Fatigue
(The American Society of Mechanical Engineers (ASME), 1985)Many structural members in service experience fluctuating loads and temperatures. Thermal stresses devlop on a contrained element if the temperature is cycled. Constraint exists in structural ... -
Relationship Between Fatigue Life Distribution, Notch Configuration, and S-N Curve of a 2024-T4 Aluminum Alloy
(The American Society of Mechanical Engineers (ASME), 1985)The objective of this study is to identify the most closely related variable to the distribution of fatigue life in unnotched and three kinds of notched 2024-T4 aluminum alloy specimens. ... -
The End Rotation of a Notched Bar in Mode 1 Deformation
(The American Society of Mechanical Engineers (ASME), 1985) -
Buckling in Rotary Forging and Ring Rolling
(The American Society of Mechanical Engineers (ASME), 1985)The possibility of promoting out-of-plane elastic buckling in thin disk rotary forming and in ring rolling, by the application of load through forming tools applied over a small sectional element ... -
On the Prediction of Stress Intensity Factors for Axisymmetric Cracks in Thin-Walled Cylinders From Plane Strain Solutions
(The American Society of Mechanical Engineers (ASME), 1985)It is shown that stress intensity solutions for axisymmetric cracks in thin-walled cylinders may be obtained for any prescribed axial stress distribution from plane strain solutions. This approach ... -
Relation Between Concentration of Salt Water and Corrosion Fatigue Strength on 0.37 Percent Carbon Structural Steel
(The American Society of Mechanical Engineers (ASME), 1985)The corrosion fatigue properties of 0.37 percent carbon structural steel (AISI 1035) were studied in salt water having concentrations from 0 wt percent (ion exchanged water) to 10 wt percent. ... -
Elastic-Plastic Fracture Mechanics Analysis on Environmentally Accelerated Cracking of Stainless Steel in High Temperature Water
(The American Society of Mechanical Engineers (ASME), 1985)Stress corrosion crack growth during slow strain rate testing was investigated using elastic-plastic fracture mechanics. Thin compact and center-notched specimens of sensitized Type 304 stainless ... -
Laser Heat Treatment of Cast Irons—Optimization of Process Variables: Part I
(The American Society of Mechanical Engineers (ASME), 1985)A 1.2 kw CO2 -CW laser operating in ring and Gaussian beam modes was used to surface harden gray and ductile cast irons. The microstructure, case depth, hardness, surface integrity, and ... -
Low Cycle Fatigue Crack Growth Behavior at Elevated Temperature Under the Combined Strain-Wave-Shape Cycling in Type 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1985)The low-cycle fatigue crack growth behavior of Type 304 stainless steel, when the slow-fast type strain cycles were introduced into the repeat of fast-fast type strain cycle either in a ... -
The Electrical Discharge Compaction of Powder: Mechanics and Material Structure
(The American Society of Mechanical Engineers (ASME), 1985)The response of metal powders contained in columnar form to high voltage electrical discharge between its ends is described in terms of the electrical, physical, morphological, and compositional ... -
A Method for Measurement of Axisymmetric Axial Residual Stresses in Circumferentially Welded Thin-Walled Cylinders
(The American Society of Mechanical Engineers (ASME), 1985)A new method is proposed for measuring the axial component of an axisymmetric residual stress field in thin-walled cylinders. The specific application considered is determination of the stress ... -
Discussion: “On the Prediction of Stress Intensity Factors for Axisymmetric Cracks in Thin-Walled Cylinders From Plane Strain Solutions” (Cheng, Weili, and Finnie, Iain, 1985, ASME J. Eng. Mater. Technol., 107, pp. 227–231)
(The American Society of Mechanical Engineers (ASME), 1985)