Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2541-2560 of 3257
-
The Effects of Material Strength, Stress Ratio, and Compressive Overload on the Threshold Behavior of a SAE1045 Steel
(The American Society of Mechanical Engineers (ASME), 1985)The fatigue crack growth rate behavior of a SAE1045 steel in the as received condition and four different quenched and tempered conditions was studied as a function of stress ratio and peak ... -
Constitutive Equation of Cyclic Softening
(The American Society of Mechanical Engineers (ASME), 1985)A constitutive equation of cyclic strain softening for materials with low internal stress levels was derived from the rate equation. The study showed that cyclic strain softening is associated ... -
Effect of Heat-Treatment Upon the Fatigue-Crack Growth Behavior of Alloy 718 Weldments—Part I: Macroscopic Behavior
(The American Society of Mechanical Engineers (ASME), 1985)Gas-tungsten-arc weldments in Alloy 718 were studied in fatigue-crack growth tests conducted at five temperatures over the range 24–649°C. In general, crack growth rates increased with ... -
The Influence of Load Ratio and Temperature on the Near-Threshold Fatigue Crack Growth Rate Properties of Pressure Vessel Steels
(The American Society of Mechanical Engineers (ASME), 1985)Near-threshold fatigue crack propagation behavior was examined in four pressure vessel steels (SA508 Cl 2a, SA533 Gr A Cl 2, SA508 Cl 3a, and SA533 Gr B Cl 2) and two submerged arc weldments ... -
Cyclic Torsion of a Circular Cylinder and Its Residual Stress Distribution
(The American Society of Mechanical Engineers (ASME), 1985)The endochronic theory of plasticity is applied to discuss the cyclic full-reversed torsional loading of a solid bar with circular cross section. Numerical techniques are employed to obtain the ... -
Combined Viscous and Plastic Deformations in Two-Dimensional Large Strain Finite Element Analysis
(The American Society of Mechanical Engineers (ASME), 1985)Capabilities for the analysis of combined viscous and plastic behavior have been added to an existing finite element computer program for two-dimensional elastic-plastic calculations. This program ... -
Sustained-Load Crack-Growth in Inconel 718 Under Nonisothermal Conditions
(The American Society of Mechanical Engineers (ASME), 1985)Sustained-load crack-growth experiments were conducted under isothermal and nonisothermal conditions. Temperature cycling was conducted between 537° and 649°C. Hold times at minimum and/or ... -
Threshold and Near Threshold Fatigue Crack Growth of Five Cast Steels at Room Temperature and −45°C
(The American Society of Mechanical Engineers (ASME), 1985)Threshold and near threshold fatigue crack growth behavior was obtained for five carbon or low alloy cast steels at room temperature and −45°C (−50°F) with the load ratio R=0.05 and ... -
Isostatic Pressing Technology
(The American Society of Mechanical Engineers (ASME), 1985) -
Coatings for High Temperature Applications
(The American Society of Mechanical Engineers (ASME), 1985) -
Surface Coatings, Volume I: Raw Materials and Their Usage
(The American Society of Mechanical Engineers (ASME), 1985) -
Treatise on Materials Science and Technology, Vol. 19, Experimental Methods, Part B
(The American Society of Mechanical Engineers (ASME), 1985) -
Fatigue Crack Growth of Duplex Stainless Steel Castings at 4 K
(The American Society of Mechanical Engineers (ASME), 1985)Constant-load-amplitude stage II fatigue crack growth rates at 4 K were measured for duplex stainless steel castings. The results show that at a ΔK of 60 MPa•m1/2 , da/dN = 7.6 × 10−4 ... -
A Constitutive Model of Creep Describing Creep Recovery and Material Softening Caused by Stress Reversals
(The American Society of Mechanical Engineers (ASME), 1985)The constitutive model of creep proposed by the present authors on the basis of a creep-hardening surface in creep strain space (CHS model) is first modified to incorporate creep recovery. It ... -
A Computational Temperature Analysis for Induction Heating of Welded Pipes
(The American Society of Mechanical Engineers (ASME), 1985)Recent approaches to controlling stress corrosion cracking in welded 304 stainless steel pipes have been based on various types of controlled heating procedures. When applied properly, the heating ... -
Numerical Analysis on the Barreling of Solid Cylinders Under Axisymmetric Compression
(The American Society of Mechanical Engineers (ASME), 1985)Diameter ratio, height reduction ratio, and aspect ratio are very significant non-dimensional parameters that govern the geometry of barreling throughout the process of plastic deformation of ... -
Biaxial Strength of HY 80 Steel
(The American Society of Mechanical Engineers (ASME), 1985)The biaxial deformation behavior of HY 80 steel has been examined by testing thin wall tubes under combined axial tension and internal pressure. The effective stress-strain curves and the ... -
Crack Growth and Instable Fracture of Rotating Disks
(The American Society of Mechanical Engineers (ASME), 1985)The fracture of rotating disks that have cracks and/or notches is predicted employing the crack instability criterion based on the J-integral R-curve approach characterizing a material resistance ... -
Barreling of Solid Cylinders Under Axial Compression
(The American Society of Mechanical Engineers (ASME), 1985)Axisymmetric compression tests of solid aluminum cylinders, over a wide range of “aspect ratios” (length/diameter) and both under dry as well as lubricated conditions, suggest that the resulting ... -
Development of an Experimental Facility for Single and Multistage, Constant Strain Rate Compression
(The American Society of Mechanical Engineers (ASME), 1985)Detailed knowledge of material properties is one of the most important aspects of predictive-adaptive computer models used to control hot strip mills. The paper critically reviews the techniques, ...