Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2521-2540 of 3257
-
The Freely Expanding Ring Test—A Test to Determine Material Strength at High Strain Rates
(The American Society of Mechanical Engineers (ASME), 1986)The freely expanding ring test (ERT) is a conceptually simple test for determining the stress-strain behavior of materials at large strains and at high strain rates. This test is conducted by ... -
An Analysis of Drawbeads in Sheet Metal Forming: Part I—Problem Formulation
(The American Society of Mechanical Engineers (ASME), 1986)The development of a one-dimensional finite strain elasto-plastic shell model appropriate for use in modelling straight drawbeads is outlined. Numerical results obtained using a finite element ... -
Delamination Fracture Toughness of Graphite and Aramid Epoxy Composites
(The American Society of Mechanical Engineers (ASME), 1986)The delamination fracture toughness of graphite and aramid-epoxy composite laminates was determined as a function of loading rate for unidirectional and woven reinforcements. In addition, the ... -
Characterization of Optical and Surface Parameters During Particle Impact Damage
(The American Society of Mechanical Engineers (ASME), 1986)The damage caused by sand impingement can be severe and detrimental to canopies, radomes, wind screens, and structural components resulting in loss of transmittance, communications, and premature ... -
Tensile and Fracture Properties of an Fe-18Cr-20Ni-5Mn-0.16N Fully Austenitic Weld Metal at 4 K
(The American Society of Mechanical Engineers (ASME), 1986)The 4-K tensile and fracture toughess properties of a fully austenitic stainless steel weld are reported. One tensile and two compact tension fracture specimens were tested. The weld was produced ... -
Constitutive Models Suitable for Thermal Loading
(The American Society of Mechanical Engineers (ASME), 1986)A non-unified creep plasticity constitutive model and a unified creep-plasticity model have been considered. In the non-unified model, creep and plastic strains were added separately; in the ... -
New Measuring Method of Axisymmetric Three-Dimensional Residual Stresses Using Inherent Strains as Parameters
(The American Society of Mechanical Engineers (ASME), 1986)For the measurement of axisymmetric three-dimensional residual stresses, Sachs’ method is often used. The accuracy of this method is not high when even small errors are contained in observed ... -
Measuring Engineering Properties of Soil
(The American Society of Mechanical Engineers (ASME), 1986) -
Conduction of Heat in Solids, Second Edition
(The American Society of Mechanical Engineers (ASME), 1986) -
Integral Methods in Science and Engineering
(The American Society of Mechanical Engineers (ASME), 1986) -
Probabilistic Methods in Structural Engineering
(The American Society of Mechanical Engineers (ASME), 1986) -
Macro-Mechanical Analysis for Symmetric and Asymmetric Fully Plastic Crack Growth
(The American Society of Mechanical Engineers (ASME), 1986)Asymmetries like welds or shoulders, may eliminate one of the two shear zones of symmetrically fully plastic cracked parts and thus give crack propagation along the remaining active slip band ... -
Handbook of Mechanics, Materials, and Structures
(The American Society of Mechanical Engineers (ASME), 1986) -
Notch Effect in Low-Cycle Fatigue at Elevated Temperatures—Life Prediction From Crack Initiation and Propagation Considerations
(The American Society of Mechanical Engineers (ASME), 1986)This paper describes the notch effect in low-cycle fatigue of an austenitic stainless steel SUS 304 at 873 K in air. Total strain range-controlled tests were carried out using a round unnotched ... -
Analytical Study of Thick Walled Porous Cylinder
(The American Society of Mechanical Engineers (ASME), 1985)An analytical study has been herein presented to predict the stress distribution in thick-walled porous (permeable) cylinders subjected to internal and/or external pressures. The maximum induced ... -
Thermal Aging of Cast Stainless Steel, and Its Impact on Piping Integrity
(The American Society of Mechanical Engineers (ASME), 1985)A series of experiments were conducted to characterize the effects of high temperature service (550–650°F or 288–343°C) on the mechanical properties of cast stainless steels. The material ... -
A Continuous Damage Mechanics Model for Ductile Fracture
(The American Society of Mechanical Engineers (ASME), 1985)A model of isotropic ductile plastic damage based on a continuum damage variable, on the effective stress concept and on thermodynamics is derived. The damage is linear with equivalent strain ... -
Vibration-Induced Wear of Heat Exchanger Tubes
(The American Society of Mechanical Engineers (ASME), 1985)An analytical and experimental investigation has been made of the wear of a heat exchanger tube vibrating against a tube support. The purpose of this investigation is to develop a predictive ... -
Rake and Flank Wear Mechanisms of Coated and Uncoated Cemented Carbides
(The American Society of Mechanical Engineers (ASME), 1985)A series of commercially available cemented carbides coated with single or composite layers of TiC, TiN, and Al2 O3 were used to cut three types of steel, En8 (∼AISI 1042), En24 (∼AISI 4340), ... -
Effect of Heat-Treatment Upon the Fatigue-Crack Growth Behavior of Alloy 718 Weldments—Part II: Microscopic Behavior
(The American Society of Mechanical Engineers (ASME), 1985)The microstructural features that influenced the fatigue-crack growth behavior of as-welded, conventional heat-treated, and modified heat-treated Alloy 718 GTA weldments were studied. Electron ...