Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2501-2520 of 3257
-
Advanced Fracture Mechanics
(The American Society of Mechanical Engineers (ASME), 1986) -
Investigation of Endochronic Constitutive Equation Subject to Plastic Strain-Controlled Axial-Torsional Deformation
(The American Society of Mechanical Engineers (ASME), 1986)Plastic-strain controlled test is investigated both experimentally and theoretically. The plastic-strain control is feasible by means of computer-aided material test system. Theoretical study is ... -
The Coefficients of Thermal Expansion of La2O3, TaVO5 and Ta16W18O94 Below Room Temperature
(The American Society of Mechanical Engineers (ASME), 1986)The coefficients of thermal expansion (CTE) of La2 O3 , TaVO5 and Ta16 W18 O94 were measured in the temperature range 150–300 K for space applications. Hot pressed La2 O3 showed a positive ... -
Laser Heat Treatment of Cast Irons—Optimization of Process Variables, Part II
(The American Society of Mechanical Engineers (ASME), 1986)ASTM class 40 gray and 80-55-06 ductile cast irons were surface heat-treated by a 1.2-kW, CO2 laser to study the effects of square and oscillating-gaussian beam modes on case depth, coverage ... -
Modeling Plastic Deformation of Mild Steel Under Nonproportional Deformation Path
(The American Society of Mechanical Engineers (ASME), 1986)An elastic/viscoplastic theory that includes anisotropic strain hardening is used in the analysis of a nonproportional biaxial torsion-tension loading test. The theory is a combination of the ... -
Current Research on Fatigue Cracks (in English)
(The American Society of Mechanical Engineers (ASME), 1986) -
The Coefficient of Thermal Expansion of a Super Invar-Ta16W18O94 Composite
(The American Society of Mechanical Engineers (ASME), 1986)The coefficient of thermal expansion (CTE) of a hot pressed Ta16 W18 O94 which was produced from Ta2 O5 and WO3 powders was found to be −1.52×10−6 K−1 in the temperature range 180–330 ... -
Determination of Tensile Properties by a Three-Point Method
(The American Society of Mechanical Engineers (ASME), 1986)It is shown that it is possible to use a three-point method for the evaluation of tensile data for some ductile metals. The experimental data show also that average tensile stresses and axial ... -
Response of Two Aluminum Alloys to Single and Multistage Compression
(The American Society of Mechanical Engineers (ASME), 1986) -
A Comparison of Crack-Tip Field Parameters for Large and Small Fatigue Cracks
(The American Society of Mechanical Engineers (ASME), 1986)A comparison of the elastic-plastic crack-tip fields of large and small fatigue cracks has been made using the ΔJ-integral approach. Using experimental strain and displacement range measurements ... -
Thermal Expansion Behavior of Alloyed Pearlitic Flake Graphite Cast Irons
(The American Society of Mechanical Engineers (ASME), 1986)Precise understanding of thermal expansion behavior of flake graphite cast irons is essential to know the thermal fatigue resistance of these irons when used for elevated temperature application ... -
Shear Plastic Stress-Strain Relation Obtained From Torque-Twist Data
(The American Society of Mechanical Engineers (ASME), 1986)A standard technique for finding the shear stress-strain relation of a material employs a torsion test on a solid circular cylinder. It is shown that the exact solution is easily obtained as ... -
Erratum: “Measurement of Residual Hoop Stresses in Cylinders Using the Compliance Method” (Journal of Engineering Materials and Technology, 1986, 108, pp. 87–92)
(The American Society of Mechanical Engineers (ASME), 1986) -
Advanced Ceramic Materials: Technological and Economic Assessment
(The American Society of Mechanical Engineers (ASME), 1986) -
Fatigue Crack Growth Under General-Yielding Cyclic-Loading
(The American Society of Mechanical Engineers (ASME), 1986)In low cycle fatigue, cracks are initiated and propagated under general-yielding cyclic-loading. For general-yielding cyclic-loading, Dowling and Begley have shown that fatigue crack growth rate ... -
Optimum Working Conditions in Thick Walled Cylinders
(The American Society of Mechanical Engineers (ASME), 1986)Although thick walled cylinders subjected to both pressure difference and internal heat flow can be found in many engineering applications, optimizing for maximum material utilization is still ... -
Strain Rate Sensitivity, Strain Hardening, and Yield Behavior of 304L Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1986)Sheet and rod stock of 304L stainless steel were tested in uniaxial tension and compression at strain rates between 10−4 s−1 and 104 s−1 . To evaluate the yield locus behavior of the sheet ... -
Nondestructive Evaluation of Adhesively Bonded Joints
(The American Society of Mechanical Engineers (ASME), 1986)In this experiment, the method of phase spectral analysis was used to monitor ultrasonic moduli changes in a two part epoxy adhesive bonded between steel adherends during cure as well as ... -
Modeling Internal Stresses in the Nonelastic Deformation of Metals
(The American Society of Mechanical Engineers (ASME), 1986)The roles of short range and long range internal stresses during nonelastic deformation have been postulated and explored using the MATMOD-4V deformation model. New microstructural variables have ... -
An Experimental Investigation of the Yield Loci of 1100-0 Aluminum, 70:30 Brass, and an Overaged 2024 Aluminum Alloy After Various Prestrains
(The American Society of Mechanical Engineers (ASME), 1986)The multiaxial yield behaviors of 1100-0 aluminum, 70:30 brass, and an overaged 2024 aluminum alloy (2024-T7) have been investigated for a variety of prestress histories involving combinations ...