Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2481-2500 of 3257
-
Observations of Material Behavior Under Isothermal and Thermo-Mechanical Loading
(The American Society of Mechanical Engineers (ASME), 1986)Deformation and damage behavior of a 1070 steel (class U wheel steel) under thermo-mechanical and isothermal loading have been examined. Fatigue lives under thermo-mechanical and isothermal loading ... -
Introduction to Symposium on Crack Growth Behavior and Performance of Structural Components Susceptible to Stress Corrosion Cracking
(The American Society of Mechanical Engineers (ASME), 1986) -
A Mechanistic Perspective of the Biaxial Strength of Paperboard
(The American Society of Mechanical Engineers (ASME), 1986)Prior research has demonstrated the practical significance of biaxial strength and established methods for measuring and predicting biaxial properties. Analytical models have been shown to accurately ... -
Experimental Evaluation of Creep Constitutive Equations for Type 304 Stainless Steel Under Non-Steady Multiaxial States of Stress
(The American Society of Mechanical Engineers (ASME), 1986)In order to evaluate the validity and limitations of the creep-hardening surface model proposed by the present authors, a series of creep tests for type 304 stainless steel were performed at ... -
Transient Small-Scale Yield Behavior of Textured Copper Tubing Under Biaxial Loading
(The American Society of Mechanical Engineers (ASME), 1986)Biaxial microplastic yielding (8 microstrain) of 101 copper tubing was studied at room temperature to assess the transient time-dependent behavior of subsequent yielding following small prestrains ... -
On the Mechanics of Grey Cast Iron Under Pure Bending
(The American Society of Mechanical Engineers (ASME), 1986)This paper presents the results of experiments conducted on lamellar graphite grey cast iron of rectangular section subjected to pure bending. Strain measurements confirm the traditional speculation ... -
Determination of Stress Intensity Factors for Partial Penetration Axial Cracks in Thin-Walled Cylinders
(The American Society of Mechanical Engineers (ASME), 1986)An approach based on the use of rotation and displacement solutions for a cracked element in plane strain is used to obtain the stress intensity factor for a long axial crack in a thin-walled ... -
A Theoretical Derivation of the Similarity of Dynamic Compaction Processes of Powder Media in Dies
(The American Society of Mechanical Engineers (ASME), 1986)Multiple shock compactions of powder media within a die with a rigid punch are theoretically investigated. First, similarity of dynamic compaction processes for a powder medium of a simple type ... -
Measurement of Residual Hoop Stresses in Cylinders Using the Compliance Method
(The American Society of Mechanical Engineers (ASME), 1986)A method is proposed for measurement of the hoop stress in an axisymmetric residual stress field in cylinders in which the axial stress is independent of the axial coordinate. The method ... -
Residual Stress Distribution in Machining Annealed 18 Percent Nickel Maraging Steel
(The American Society of Mechanical Engineers (ASME), 1986)A novel electrolytic etching technique is used to determine the residual stress distribution in the machining of annealed 18 percent nickel maraging steel. Ring shaped specimens were machined ... -
A Three-Dimensional Finite Element Evaluation of a Destructive Experimental Method for Determining Through-Thickness Residual Stresses in Girth Welded Pipes
(The American Society of Mechanical Engineers (ASME), 1986)The accuracy of a destructive, experimental method for the evaluation of through-thickness residual stress distributions is investigated. The application of the method is to a welded pipe that ... -
Ultrasonic Fretting Wear of a Plain Carbon Steel
(The American Society of Mechanical Engineers (ASME), 1986)The fretting wear characteristics of a low-carbon steel (AISI 1018) at a 20 kHz ultrasonic testing frequency have been studied. The tests show that after an initial running-in period there ... -
A Finite Element Modelling of Embrittlement in Composite Liquid Phase Sintered Heavy Alloys
(The American Society of Mechanical Engineers (ASME), 1986)Sintered tungsten base heavy alloys made of tungsten grains embedded in a nickel rich matrix can possess low room temperature ductility that may be improved by subsequent heat treatment. The ... -
Solid Phase Sheet Forming of Thermoplastics—Part II: Large Deformation Post-Yield Behavior of Plastics
(The American Society of Mechanical Engineers (ASME), 1986)This paper examines the phenomenology of the large strain, post-yield behavior of the three thermoplastics—polycarbonate, polybutylene terephthalate and polyetherimide—from the point of view of the ... -
Solid Phase Sheet Forming of Thermoplastics—Part I: Mechanical Behavior of Thermoplastics to Yield
(The American Society of Mechanical Engineers (ASME), 1986)The detailed mechanical behavior to yield of three thermoplastics—polycarbonate, polybutylene terephthalate, and polyetherimide—subjected to simulated forming histories, is examined in order to gain ... -
Tensile Fracture Loci for Brittle Materials Containing Spherical Voids
(The American Society of Mechanical Engineers (ASME), 1986)When very brittle materials are subjected to a complex state of stress they fail by maximum intensified tensile stress criterion first introduced by Griffith [1]. Nominal applied stresses are ... -
A New Workability Criterion for Ductile Metals
(The American Society of Mechanical Engineers (ASME), 1986)The forming limit curves are important aids in determining the extent of deformation a material can be subjected to during a forming process. In this paper a forming limit criterion for bulk ... -
Assessment of Work-Hardening Characteristics and Limit Strains of Anisotropic Aluminum Sheets in Biaxial Stretching
(The American Society of Mechanical Engineers (ASME), 1986)In this work, commercially pure aluminum sheets in both the as-received and annealed conditions are tested in uniaxial and biaxial tension. Biaxial stretching is performed in dies giving different ... -
The Determination of Stress-Strain Curves of Thin Layers Using Indentation Tests
(The American Society of Mechanical Engineers (ASME), 1986)A method is presented for estimating the plastic part of stress-strain curves of metal coatings, using a Brinell indentation test. The accuracy of the stress-strain curves obtained in this way ... -
Sheet Metal Forming Limits Under Complex Strain Paths Using Void Growth and Coalescence Model
(The American Society of Mechanical Engineers (ASME), 1986)It is well established that ductile fracture occurs by nucleation, growth and coalescence of voids. Several models have been developed to predict limits under constant strain ratio paths considering ...