Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2461-2480 of 3257
-
Study of Affecting Parameters in Laser Hole Drilling of Sheet Metals
(The American Society of Mechanical Engineers (ASME), 1987)In practical applications of laser drilling the quality of the drilled hole is the critical factor, and recently methods of studying the influence on quality of the main process variables have ... -
On the Mechanism of Fracture in Grey Cast Iron
(The American Society of Mechanical Engineers (ASME), 1987)This paper presents the results of both experimental and analytical investigations into the conditions of failure for lamellar-graphite case iron under various modes of loading. The orientation ... -
Earthquake Resistant Building Design and Construction
(The American Society of Mechanical Engineers (ASME), 1987) -
Prevention of Fracture of Cracked Steel Bars Using Laser: Part II—Laser Welding
(The American Society of Mechanical Engineers (ASME), 1986)This paper investigates the effect of laser welding on the prevention of fracture of cracked steel specimens. Precracks occurred in shaft specimens of SAE 1015 were welded by a CO2 laser, and ... -
Stress-Time-Temperature-Humidity Effects on Demination of Graphite/Epoxy Laminates
(The American Society of Mechanical Engineers (ASME), 1986)The effect of sustained load and hygrothermal environments on Mode I delamination behavior of T300/934 unidirectional graphite/epoxy laminates has been studied. Several double cantilever beam ... -
Effects of Prior Plasticity on Subsequent Creep of Type 316 Stainless Steel at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1986)Interaction between creep and plastic deformation was studied experimentally for type 316 stainless steel at 650°C, with special emphasis on creep behavior subsequent to plastic prestraining. ... -
Evaluation of Bodner-Partom Model Parameters at High Strain Rate
(The American Society of Mechanical Engineers (ASME), 1986)The objective of this paper is to model the high strain rate material behavior of metals using Bodner-Partom visco-plastic constitutive model. A unique algorithm has been developed to evaluate ... -
Evaluation of Crack Growth in Oxygenated High Temperature Water Using Full Size Pipe Tests
(The American Society of Mechanical Engineers (ASME), 1986)Full Size pipe tests have been conducted as part of EPRI research programs at the General Electric Company to verify IGSCC crack growth predictions made using a linear elastic fracture mechanics ... -
Cyclic Crack Growth Behavior of Reactor Pressure Vessel Steels in Light Water Reactor Environments
(The American Society of Mechanical Engineers (ASME), 1986)During normal operation light water reactor (LWR) pressure vessels are subjected to a variety of transients resulting in time varying stresses. Consequently, fatigue and environmentally assisted ... -
The Effect of BWR Startup Environments on Crack Growth in Structural Alloys
(The American Society of Mechanical Engineers (ASME), 1986)During startup of a Boiling Water Reactor (BWR), the water chemistry and temperature are constantly changing. Special operational practices can be performed to control the dissolved oxygen level ... -
A Comparison of Hydrogen and Mercury Embrittlement in Monel at Room Temperature
(The American Society of Mechanical Engineers (ASME), 1986)Slow strain rate tensile tests were performed on annealed and cold drawn Monel 400 and Monel R405 at room temperature in air, mercury, and electrolyte hydrogen. Hydrogen and mercury caused ... -
Crack Growth Behavior of Aluminum Alloys Tested in Liquid Mercury
(The American Society of Mechanical Engineers (ASME), 1986)Crack growth rate measurements have been made in three mercury embrittled aluminum alloys each under three loading conditions. The alloys were 1100-0, 6061-T651, and 7075-T651. The loading ... -
Study on Tensile Strength of Resin Mortar
(The American Society of Mechanical Engineers (ASME), 1986)A new resin mortar has been developed to facilitate a small-diameter shield tunneling method. The breaking elongation, Young’s modulus and tensile strength of the resin mortar are measured and ... -
The Benefit of Hydrogen Addition to the Boiling Water Reactor Environment on Stress Corrosion Crack Initiation and Growth in Type 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1986)Intergranular Stress Corrosion Cracking (IGSCC) in Type 304 stainless steel in high temperature high purity water requires the simultaneous presence of sensitized material, high tensile stress and ... -
Formulation of Cross-Hardening in Creep and its Effect on the Creep Damage Process of Copper
(The American Society of Mechanical Engineers (ASME), 1986)The present paper is concerned with the modelling of creep and creep damage in polycrystalline metals and the experimental evaluation of the proposed model. By ascribing the reduction of creep ... -
Stress Corrosion Crack Growth Rates in Type 304 Stainless Steel in Simulated BWR Environments
(The American Society of Mechanical Engineers (ASME), 1986)Stress corrosion cracking of Type 304 stainless steel has been studied with fracture-mechanics-type standard 25.4-mm-thick compact tension specimens in simulated boiling-water reactor environments ... -
Effect of Yield Stress and Grain Size on Threshold and Fatigue Limit
(The American Society of Mechanical Engineers (ASME), 1986)Experimental investigations have been carried out to study the effects of grain size and yield stress on fatigue limit and threshold stress intensity range. The relations between fatigue limit ... -
Variation of Fatigue Notch Factor With Lifetime, Stress Ratio and Temperature
(The American Society of Mechanical Engineers (ASME), 1986)An understanding of the influence of various loading parameters on the fatigue notch factor Kf is important to the designer, who often relies exclusively on the limited fatigue data available ... -
An Engineering Approach to the Prediction of Creep Crack Growth
(The American Society of Mechanical Engineers (ASME), 1986)This paper is concerned with assessing the integrity of cracked engineering components which operate at elevated temperatures. Fracture mechanics parameters are discussed for describing creep crack ... -
Surface Crack Growth Behavior of Structural Metals in High Temperature Water Environments
(The American Society of Mechanical Engineers (ASME), 1986)This paper reports on a study of surface crack growth of two nuclear structural steels, SA333 Gr6 carbon steel used for piping and SA533 Grade B pressure vessel steel, both tested under ...