Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2441-2460 of 3257
-
Techniques to Predict Dislocation Generation During Growth of Silicon Ribbon
(The American Society of Mechanical Engineers (ASME), 1987)This paper describes the numerical techniques that are used to predict stresses, strains, dislocation densities, and buckling during the growth of flat plate silicon. High quality silicon ribbon ... -
Detailed and Simplified Elastoplastic Analyses of a Cyclically Loaded Notched Bar
(The American Society of Mechanical Engineers (ASME), 1987)To find some features in the development of cyclic hardening in structural components with areas of strain concentration, detailed and simplified elastoplastic analyses are performed on an ... -
Corrosion Resistance Tables: Metals, Plastics, Nonmetals and Rubbers, 2nd Ed.
(The American Society of Mechanical Engineers (ASME), 1987) -
Relation Between Cyclic Creep and Pure Creep on Copper
(The American Society of Mechanical Engineers (ASME), 1987)The behavior of a pure copper subject to pure creep and cyclic creep under imposed load is examined at room temperature, and at 200°C, 300°C, and 400°C to show the relation ... -
Fatigue Characteristics of Laser Surface-Hardened Cast Irons
(The American Society of Mechanical Engineers (ASME), 1987)Contrary to expectations, laser surface heat treatment has a deleterious effect on the fatigue performance of pearlitic gray and ductile cast irons. A 1.2 kW, continuous wave, CO2 gas laser, ... -
An Advanced 12Cr Steel Rotor Applicable to Elevated Steam Temperature 593°C
(The American Society of Mechanical Engineers (ASME), 1987)The upper limit of steam temperature which 12Cr steel rotors can withstand has been considered to be 566°C, but the recent projects on the advanced steam turbine of large capacity demand ... -
The Fracture Toughness of Hardened Tool Steels
(The American Society of Mechanical Engineers (ASME), 1987)This report details the development of a three-stage fracture toughness testing procedure used to study the effect of tempering temperature on toughness in 01 tool steel. Modified compact tension ... -
Constitutive Equations for Nonproportional Cyclic Elasto-Viscoplasticity
(The American Society of Mechanical Engineers (ASME), 1987)This paper is concerned with the behavior of metallic materials under general complex loadings. A complete experimental investigation is carried out to exhibit the main features of this behavior. ... -
A New Method for Measurement of Residual Axial Stresses Applied to a Multi-Pass Butt-Welded Cylinder
(The American Society of Mechanical Engineers (ASME), 1987)A method based on fracture mechanics solutions for a circumferential crack is used to measure the distribution of axial residual stresses in the circumferential weld between two cylinders. The ... -
The Role of Constitutive Formulation in the Analysis of Hot Rolling
(The American Society of Mechanical Engineers (ASME), 1987)The effect of constitutive modelling of material behavior on the predictive abilities of two models of flat rolling is studied. Comparison of calculated roll forces and powers to those measured ... -
The Influence of Microstructure on Tensile Properties of an Aluminum-Lithium Alloy
(The American Society of Mechanical Engineers (ASME), 1987)The double ligament tensile (DLT) test was used to evaluate the tensile properties and anisotropy of a lithium-containing aluminum alloy in the three orthogonal directions of the wrought ingot ... -
Experimental Verification of the Similarity of Dynamic Compaction Processes of a Copper Powder Medium in Dies of Elementary Shapes
(The American Society of Mechanical Engineers (ASME), 1987)The similarity of dynamic compaction processes was investigated theoretically and predicted in our previous report, where powder media in a die were assumed to be of a simple type, and the ... -
Development of a Coal Ash Corrosivity Index for High Temperature Corrosion
(The American Society of Mechanical Engineers (ASME), 1987)Current development of Advanced Steam Cycle coal-fired power plants requires superheater and reheater tubing alloys which can withstand severe conditions for high temperature corrosion. A corrosion ... -
Multiaxial Fatigue Damage Models
(The American Society of Mechanical Engineers (ASME), 1987)Two multiaxial fatigue damage models are proposed: a shear strain model for failures that are primarily mode II crack growth and a tensile strain model for failures that are primarily mode I ... -
Handbook of Modern Grinding Technology
(The American Society of Mechanical Engineers (ASME), 1987) -
Acoustic & Electromagnetic Waves
(The American Society of Mechanical Engineers (ASME), 1987) -
Effect of Shock and Elastic Waves on Dynamic Compaction Process of Two-Layer Powder Media
(The American Society of Mechanical Engineers (ASME), 1987)The dynamic compaction processes of copper powder which was filled in two layers into a die and subjected to solid punch impaction were investigated experimentally in order to assess the effect ... -
Thermodynamic Characterization of Microcrack Dependent Material Response Properties
(The American Society of Mechanical Engineers (ASME), 1987)Available experimental data from uniaxial tests are analyzed to estimate values for parameters of a microcrack dependent model of material response. The experimental data on microcrack density ... -
Redundant Deformation Factor Evaluation Through the Stress-Strain Curves Superposition Method in Round Section Bar Drawing—A Literature Analysis
(The American Society of Mechanical Engineers (ASME), 1987)An analysis of the stress-strain curves superposition method for the evaluation of the average deformation ε and redundant deformation factor φ is presented. This approach, originally proposed ... -
Redundant Deformation Factor Evaluation Through the Stress-Strain Curves Superposition Method in Round Section Bar Drawing—Experimental Results
(The American Society of Mechanical Engineers (ASME), 1987)Based on a previous literature analysis of the stress-strain curves superposition method for the evaluation of the redundant deformation factor φ, an experimental program is proposed and carried ...