Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2421-2440 of 3257
-
The Correlation Between the Residual Stresses of ABS Terpolymers and Injection Molding Conditions
(The American Society of Mechanical Engineers (ASME), 1987)Residual stresses (R.S.) in a microcomputer-controlled injection molded ABS terpolymers have been determined. The layer-removal method and the microscopic measurement techniques were used to evaluate ... -
Production of High Strength Concrete
(The American Society of Mechanical Engineers (ASME), 1987) -
Infrared Thermographic Flaw Detection in Composite Laminates
(The American Society of Mechanical Engineers (ASME), 1987)Research performed to develop thermography as a routine rapid flaw detection tool for large composite structures is presented. The externally applied thermal field (EATF) technique is described ... -
Temper-Bead Weld Heat-Affected Zone Properties in A516-70 Steel
(The American Society of Mechanical Engineers (ASME), 1987)A temper-bead welding technique has been developed to provide an alternative weld repair method in which the application of a high temperature post-weld heat treatment (PWHT) can be avoided. ... -
Plumbing Materials and Drinking Water Quality
(The American Society of Mechanical Engineers (ASME), 1987) -
An Experimental Comparison of Several Current Viscoplastic Constitutive Models at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1987)Four current viscoplastic models are compared experimentally for Inconel 718 at 593°C. This material system responds with apparent negative strain rate sensitivity, undergoes cyclic work ... -
Influence of Cathodic and Internal Trapped Hydrogen on Fatigue Crack Growth in a NiCrMoV Structural Steel
(The American Society of Mechanical Engineers (ASME), 1987)Fatigue crack propagation has been investigated in a NiCrMoV structural steel in air or in electrolytic hydrogen charging environments. The behavior of this steel containing internal trapped ... -
Local Crack-Tip Strain Concept for Fatigue Crack Initiation and Propagation
(The American Society of Mechanical Engineers (ASME), 1987)The existence of the unified local strain field where we can substantially combine the two fatigue stages, crack initiation and propagation, was experimentally confirmed. Using the fine-grid-method, ... -
Relationship of Crack Growth Between Thermal-Mechanical and Isothermal Low-Cycle Fatigue at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1987)The surface and through crack growth behaviors of some steels in thermal-mechanical and isothermal low-cycle fatigue at elevated temperatures were investigated. It was shown that the crack growth ... -
Effects of an Artificial Small Defect on Torsional Fatigue Strength of Steels
(The American Society of Mechanical Engineers (ASME), 1987)In order to elucidate the effect of small defects on the torsional fatigue strength of steels, reversed torsion tests were carried out on the 0.46 percent C steel specimens containing a small ... -
On the Influence of Strain-Path in Multiaxial Fatigue Failure
(The American Society of Mechanical Engineers (ASME), 1987)A set of strain-controlled experiments has been performed on tubular specimens of annealed stainless steel. The strain-paths are designed to highlight the characteristics of path-dependence in the ... -
Fracture Modes and Low Cycle Biaxial Fatigue Life at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1987)This paper describes the crack growth direction in biaxial low cycle fatigue under combined axial and torsional stresses in hollow cylindrical specimens of type 304 stainless steel at 923 K ... -
The Characterization of Materials by Precision Strain Rate Sensitivity
(The American Society of Mechanical Engineers (ASME), 1987)Strain rate sensitivity is a measurement of the thermodynamic response of materials to changes in stress (τ). Correlations of the theoretical derivations to measured values are only valid if ... -
Physical Metallurgy
(The American Society of Mechanical Engineers (ASME), 1987) -
Characterization of Strain Fields Around Weld Defects
(The American Society of Mechanical Engineers (ASME), 1987)Moire interferometry is used as an alternate technique to resistance strain gages in finding full-field, local strain response of weldments to applied loads. The principles of moire interferometry ... -
Prediction of the In-Plane Electrical Conductivity of a Misoriented Short Fiber Composite: Fiber Percolation Model Versus Effective Medium Theory
(The American Society of Mechanical Engineers (ASME), 1987)The in-plane electrical conductivity of a misoriented short fiber composite was studied both by fiber percolation model (FPM) and effective medium theory (EMT). A misoriented short fiber composite ... -
Factors Influencing the Fatigue Behavior of Ferrous Laminates
(The American Society of Mechanical Engineers (ASME), 1987)Laminates based on ultrahigh carbon steel were prepared and found to exhibit enhanced fatigue life as compared to a monolithic reference material. This result was achieved through the insertion ... -
Crack-Tip-Acuity Effect on Crack Growth Initiation
(The American Society of Mechanical Engineers (ASME), 1987)For a stationary crack of an initially finite root radius in plane-strain tension, the strain fields around the smoothly blunted crack-tip are calculated for each deformation stage using the ... -
Biaxial Creep-Fatigue Failure Characteristics in Two FCC Materials
(The American Society of Mechanical Engineers (ASME), 1987)This paper describes the failure mode observed in two types of FCC structural materials: waspaloy and type 316 stainless steel as a result of biaxial low cycle fatigue at elevated temperatures. ... -
The Influence of Displacement Rate on Environmentally Assisted Cracking of Precracked Ductile Steel Specimens
(The American Society of Mechanical Engineers (ASME), 1987)Sustained load and rising displacement tests were performed on precracked specimens to investigate the environmentally assisted cracking (EAC) behavior of AISI 4340, σ0 = 1095 MPA (159 ksi), in ...