Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2261-2280 of 3257
-
Experimental Determination Technique of Stress Intensity Factor and Its Application
(The American Society of Mechanical Engineers (ASME), 1989)The proportional extrapolation technique is proposed for determining experimentally and accurately stress intensity factors, using the crack tip stresses measured by strain gage. The technique is ... -
Corrosion Fatigue Crack Growth of Steels in Various Environments
(The American Society of Mechanical Engineers (ASME), 1989)Corrosion fatigue crack growth of three steels namely: AISI C1018, AISI 4340, and Stainless 17-7PH is studied in various environments. Testing medias include natural sea water, polluted sea water ... -
Creep Deformation of Particle-Strengthened Metal-Matrix Composites
(The American Society of Mechanical Engineers (ASME), 1989)A multiaxial theory of creep deformation for particle-strengthened metal-matrix composites is derived. This derivation is based on the observation that there are two major sources of creep ... -
Frequency and Hold-Time Effects on Low Cycle Fatigue Life of Notched Specimens at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1989)This paper describes the frequency and hold-time effects on high temperature low cycle fatigue for round notched specimens. Unnotched and notched specimens having different elastic stress concentration ... -
On a Class of Kinematic Hardening Rules for Nonproportional Cyclic Plasticity
(The American Society of Mechanical Engineers (ASME), 1989)Two surface theories for rate-independent plasticity have previously been shown to offer superior correlative capability in modeling material response under non-proportional loading. In this study, ... -
Simulation of Surface Grinding
(The American Society of Mechanical Engineers (ASME), 1989)The objective in this research is to develop a mathematical model which simulates the grinding process and predicts the transient temperature field and the stresses generated in the workpiece ... -
Material Characterization for Metal-Cutting Force Modeling
(The American Society of Mechanical Engineers (ASME), 1989)Widely applicable machining simulation programs require reliable cutting force estimates, which currently can be obtained only from process-dependent machinability databases. The greatest obstacle ... -
Dynamic Equilibrium Constitutive Relations of Copper Powder Within Dies Subjected to Mutliple Shock Compactions
(The American Society of Mechanical Engineers (ASME), 1989)An approximate dynamic equilibrium pressure p -specific volume V relation exists for porous materials of a simple type undergoing mutliple shock compaction processes. A copper powder medium in ... -
Experimental Finite Element Analysis of Temperature Distribution During Arc Welding
(The American Society of Mechanical Engineers (ASME), 1989)Analysis of temperatures and associated cooling rates that arise during welding is essential in determining the final mechanical properties and load carrying capacity of the weldment. Due to the ... -
Creep Life Prediction Based on Stochastic Model of Microstructurally Short Crack Growth
(The American Society of Mechanical Engineers (ASME), 1989)A nondimensional model of microstructurally short crack growth in creep is developed based on a detailed observation of the creep fracture process of 304 stainless steel. In order to deal with ... -
Changes in State Variables at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1989)Two state variables, strength and internal (back) stress, were determined during cyclic deformation by rapid unloading-reloading experiments. The experiments were performed at different temperatures ... -
Addendum: “A Method for Dynamic Fracture Initiation Testing of Ceramics” (Journal of Engineering Materials and Technology, 1988, 110, pp. 325–331)
(The American Society of Mechanical Engineers (ASME), 1989) -
Pressure Sintering of Si3N4 System for Near-Net Shape Forming
(The American Society of Mechanical Engineers (ASME), 1989)Yttria and alumina have been used with particular success, either singly or in combination, as densification aids for hot pressing and sintering of silicon nitride. To obtain desirable mechanical, ... -
New Measuring Method of Three-Dimensional Residual Stresses in Long Welded Joints Using Inherent Strains as Parameters—Lz Method
(The American Society of Mechanical Engineers (ASME), 1989)In this paper, a new measuring method of three-dimensional residual stresses induced in a butt welded joint is presented. The proposed method is based on a general approach developed by the ... -
Mixed Mode Ductile Fracture Studies With Nonproportional Loading Based on Continuum Damage Mechanics
(The American Society of Mechanical Engineers (ASME), 1989)Service loading imposed on engineering structures is often arbitrary or nonproportional. The paper presents an investigation of examining the effects of proportional and nonproportional loadings ... -
The Structure and Mechanical Properties of Palm Timber as a Fibre Composite
(The American Society of Mechanical Engineers (ASME), 1989)A study has been made of wood extracted from the oil palm (Elaeis guineensis) , coconut palm (Cocos nucifera) , and fan palm (Borassus flabe) which are common species of tropical palms. The ... -
Creep Testing of 2.25 Cr-1 Mo Welds by DC Potential Drop Technique
(The American Society of Mechanical Engineers (ASME), 1989) -
Relationship of Creep, Creep-Fatigue, and Cavitation Damage in Type 304 Austenitic Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1989)Available creep and creep-fatigue data on type 304 stainless steel are re-examined in the light of recently generated basic cavitation data on the same material. This basic study has shown ... -
J-Integral Analysis of the Compact Tension Specimen
(The American Society of Mechanical Engineers (ASME), 1989)A J-integral solution is presented for the compact tension specimen. The solution allows analysis for crack lengths greater than 20 percent of the specimen width. Unlike previous solutions that ... -
On the Mechanics of Microcracking in Fiber Composite Laminates Under Combined Stress
(The American Society of Mechanical Engineers (ASME), 1989)The formation of matrix microcracks in fiber composite laminates has been widely observed. The present paper addresses the mechanics of this microcracking by means of a shear lag model in ...