Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2241-2260 of 3257
-
Dislocation Substructures and Nonproportional Hardening
(The American Society of Mechanical Engineers (ASME), 1990)The dislocation substructures created in 1100 aluminum, OFHC copper, and type 304 and 310 stainless steels by in-phase (proportional) and 90 deg out-of-phase (nonproportional) tension-torsion cyclic ... -
On the Calculations of the Stored Energy of Cold Work
(The American Society of Mechanical Engineers (ASME), 1990)When a metal deforms plastically, most of the mechanical energy expended in the deformation process is converted into heat and the remainder is stored in the material. A method for the ... -
Leaky Lamb Waves for the Ultrasonic Nondestructive Evaluation of Adhesive Bonds
(The American Society of Mechanical Engineers (ASME), 1990)The critical role played by interface zones in the fracture and failure of composites and other bonded materials is well known. However, the existing nondestructive evaluation methods are not ... -
Dynamic Crushing of Strain-Softening Cellular Structures—A One-Dimensional Analysis
(The American Society of Mechanical Engineers (ASME), 1990)A one-dimensional model for impact deformation of open-celled structures is used to examine the effects of material elasticity, cell inertia, cell compliance characteristics and limited crushability. ... -
An Assessment of Add-on Energy Absorbing Devices for Vehicle Crashworthiness
(The American Society of Mechanical Engineers (ASME), 1990)An alternative approach to vehicle crashworthiness improvement by inserting add-on nonstructural energy absorbing (EA) devices in the unutilized space in series with existing load paths is studied ... -
Notch Root Displacement (NRD) Approach to Predict Crack Initiation Life of Notched Specimen in High-Temperature Multiaxial Low Cycle Fatigue
(The American Society of Mechanical Engineers (ASME), 1990)This paper describes the notch root displacement (NRD) approach to assess the crack initiation life of notched specimens in high-temperature multiaxial low cycle fatigue. Two and three-dimensional ... -
High Temperature Creep Damage Under Biaxial Loading—Part I: Experiments
(The American Society of Mechanical Engineers (ASME), 1990)The respective influences of the Von-Mises equivalent stress and of the maximum principal stress on the high temperature creep damage of two industrial alloys (INCO 718 and 17–21 SPH stainless ... -
Effect of Delamination on the Nonlinear Behavior of Composite Laminated Beams
(The American Society of Mechanical Engineers (ASME), 1990)This paper presents a parametric study of the effect of delamination, and of initial imperfection, on the overall nonlinear behavior of laminated composite beams. The study is based on geometrical ... -
A Procedure for Low Cycle Fatigue Life Prediction for Various Temperatures and Strain Rates
(The American Society of Mechanical Engineers (ASME), 1990)This paper describes a procedure that permits the calculation of the fatigue life over a wide range of temperatures and strain rates. The isothermal fatigue life is expressed in terms of the ... -
Characterization of Notched Ductile Failure With Continuum Damage Mechanics
(The American Society of Mechanical Engineers (ASME), 1990)A recently developed anisotropic model of continuum damage mechanics has been applied successfully to characterize ductile fracture of cracked plates under mode I and mixed mode failures. The ... -
Investigation of Creep/Fatigue Interaction on Crack Growth in a Titanium Aluminide Alloy
(The American Society of Mechanical Engineers (ASME), 1990)Crack growth under sustained load and sustained load with superimposed fatigue cycles at elevated temperatures in a titanium-aluminide alloy (Ti3 Al) was investigated. The objectives were to ... -
Machinability of High Temperature Composites by Abrasive Waterjet
(The American Society of Mechanical Engineers (ASME), 1990)An experimental investigation was conducted on the machinability of particulate reinforced ceramic TiB2 /SiC and metal SiC/Al matrix composites by an abrasive water jet. Both piercing and slot ... -
Three-Dimensional Laser Machining of Composite Materials
(The American Society of Mechanical Engineers (ASME), 1990)This paper presents a concept for performing three-dimensional laser machining on composite materials, using two intersecting laser beams to create grooves on a workpiece. A volume of material ... -
Constitutive Modeling of Anisothermal Cyclic Plasticity of 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1989)Temperature-history dependence in anisothermal cyclic plasticity of 304 stainless steel is studied for the constitutive modeling within the temperature range from room temperature to 600°C. ... -
Further Verification of Endochronic Theory Under Biaxial Load
(The American Society of Mechanical Engineers (ASME), 1989) -
Improving the Toughness of 3-1/2NiCrMoV Steam Turbine Disk Forgings
(The American Society of Mechanical Engineers (ASME), 1989)Due to the in-service stress corrosion cracking of some 3-1/2NiCrMoV steam turbine disks, the Charpy V-notch toughness requirements for replacement forgings have dramatically increased in recent ... -
The Effect of Several Finishing Processes on the Fatigue Resistance of Hole Surfaces
(The American Society of Mechanical Engineers (ASME), 1989)This investigation examines the effects of different finishing processes on the fatigue life of premachined holes in Assab 760 steel plates. The finishing processes studied were reaming, ballizing, ... -
Temperature-Dependence of Multiaxial Non-Proportional Cyclic Behavior of Type 316 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1989)Temperature dependence of multiaxial cyclic behavior of type 316 stainless steel was elucidated experimentally. Cyclic tests under constant total-strain amplitudes were performed for uniaxial ... -
The Use of Spheroidal Graphite Cast Irons to Develop Forgeability Criteria Based on Local Strain Measurements
(The American Society of Mechanical Engineers (ASME), 1989)An attempt has been made to develop forgeability criteria based on data obtained from local strain measurements. Nodular case iron has been used as the modelling material because its microstructure ... -
Lubricant Modeling and Its Effect on Simulation of Material Forming
(The American Society of Mechanical Engineers (ASME), 1989)Solid cylinder upsetting is analyzed using three different approaches for frictional boundary condition modeling. These are (1) constant shear friction factor, (2) experimentally measured frictional ...