Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2281-2300 of 3257
-
Erratum: “Experimental Determination Technique of Stress Intensity Factor and Its Application” (Journal of Engineering Materials and Technology, 1989, 111, pp. 81–86)
(The American Society of Mechanical Engineers (ASME), 1989) -
Effects of Extremes of Hardness and Mean Stress on Fatigue of AISI 4340 Steel in Bending and Torsion
(The American Society of Mechanical Engineers (ASME), 1989)Experiments are reported for fatigue tests in bending and in torsion at hardness levels from fully annealed to fully hard and super quenched. Results indicate a linear relation between fatigue ... -
Characterization of Prepreg Tow Carbon/Epoxy Laminates
(The American Society of Mechanical Engineers (ASME), 1989)Resin systems used in wet filament winding differ from those used in prepreg laminates. However it is possible to use the resins from prepreg systems in filament winding by using prepreg tows. ... -
J-Integral Analysis of Three-Point Bend Specimen
(The American Society of Mechanical Engineers (ASME), 1989)A J-integral solution is derived for the three-point bend [SE(B)] specimen. The solution allows analysis for a/W greater than 0.2. The solution is based on an approach that does not require ... -
A Model for Abrasive-Waterjet (AWJ) Machining
(The American Society of Mechanical Engineers (ASME), 1989)Ultrahigh-pressure abrasive-waterjets (AWJs) are being developed as net shape and near-net-shape machining tools for hard-to-machine materials. These tools offer significant advantages over existing ... -
Extensive Theory of Force-Approach Relations of Elastic Spheres in Compression and in Impact
(The American Society of Mechanical Engineers (ASME), 1989)The prevailing Hertz theory in contact and in impact is based on the total compressive displacement of a semi-infinite elastic body. This paper considers displacements of finite elastic medium ... -
A Study on a Semimicroscopic Formulation of Inelastic Constitutive Equations of Polycrystalline Metals Subjected to a Large Deformation
(The American Society of Mechanical Engineers (ASME), 1989)Work-hardening mechanisms of a polycrystalline metal significant in a large deformation range are different from those in a small strain range. That is, a texture development and an effect of ... -
Fracture Mechanics Applied to Elevated Temperature Crack Growth
(The American Society of Mechanical Engineers (ASME), 1989)Twenty-six isothermal crack growth tests were performed on Hastelloy-X tubular specimens at a variety of temperatures and strain ranges. Conditions were selected to include nominally elastic and ... -
Conduction in Non-Crystalline Materials
(The American Society of Mechanical Engineers (ASME), 1989) -
A General Criterion for Low-Cycle Multiaxial Fatigue Failure
(The American Society of Mechanical Engineers (ASME), 1989)A new, general criterion is proposed for multiaxial low-cycle fatigue failure. Contours of constant fatigue life on a plot of maximum shear strain against the tensile strain acting normal to ... -
Identification of Materials Parameters for Inelastic Constitutive Models Using Principles of Biologic Evolution
(The American Society of Mechanical Engineers (ASME), 1989)A new method for the identification of materials parameters of an inelastic constitutive model is described. The method is based on the principles of biologic evolution. The efficiency of this ... -
Notch Effect in Biaxial Low Cycle Fatigue at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1989)This paper describes the notch effect in biaxial low cycle fatigue of an austenitic stainless steel SUS 304 at 873K in air. Mises’ equivalent stress controlled fatigue tests were carried out ... -
A Direct Correlation of Strength With Impact Velocity in the Taylor Test
(The American Society of Mechanical Engineers (ASME), 1989)This paper presents a method for analyzing the results of a Taylor impact test. From post-mortem measurements of final specimen length and final undeformed specimen length the dynamic material ... -
Effect of Shielding Gas Pressure in Laser Cutting of Sheet Metals
(The American Society of Mechanical Engineers (ASME), 1989)To investigate the influence of the shielding gas pressure on the laser cut quality, a series of experiments was conducted for various cutting conditions. The cutting pressure distribution was ... -
Specimen Size and Orientation Effects on the Toughness of Steel Weldments
(The American Society of Mechanical Engineers (ASME), 1989)This paper deals with the measurement of the room temperature fracture toughness of 25-mm thick HY130 steel shielded-metal-arc weldments. The multipass butt welds were tested using different ... -
Ultrasonic Wave Considerations for the Development of an NDE Feature Matrix for Anisotropic Media
(The American Society of Mechanical Engineers (ASME), 1989)The problem of ultrasonic surface and bulk wave propagation in an anisotropic media and/or a composite material is addressed so that applications in Nondestructive Evaluation can be considered, ... -
Materials Selection in Electromagnetic Launcher Design
(The American Society of Mechanical Engineers (ASME), 1989)The design of electromagnetic launchers includes a large materials selection component, with the use of available structural materials constrained by electrical performance considerations. Feasible ... -
Effects of Amplitude-History and Temperature-History on Multiaxial Cyclic Behavior of Type 316 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1989)The effects of the history in strain-amplitude and temperature variation on the multiaxial cyclic behavior of type 316 stainless steel were discussed by performing a series of total-strain ... -
Crack Instability in Pipes Containing Internal Surface Flaw
(The American Society of Mechanical Engineers (ASME), 1989)Crack associated pipe axial displacement and tearing modulus solutions are derived for pipes containing internal circumferential part-through wall surface flaw under axial tension loading. The ... -
Erratum: “Material Characterization for Metal-Cutting Force Modeling” (Journal of Engineering Materials and Technology, 1989, 111, pp. 210–219)
(The American Society of Mechanical Engineers (ASME), 1989)