Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2301-2320 of 3257
-
An Experimental Verification of the Hemispherical Cup Puckering Problem
(The American Society of Mechanical Engineers (ASME), 1989)In this work is presented an experimental study of the hemispherical cup puckering test. This investigation is motivated by some theoretical as well as by some practical reasons which are ... -
Low-Cycle Fatigue Properties of Steels and Their Weld Metals
(The American Society of Mechanical Engineers (ASME), 1989)Completely reversed, strain-controlled, low-cycle fatigue behavior at room temperature is investigated for steels and their weld metals. Weld metal specimens were taken from multi-pass weld metal ... -
Fracture Surface Orientation Under Mixed-Mode Loading
(The American Society of Mechanical Engineers (ASME), 1989) -
Wrinkling of an Unevenly Stretched Sheet Metal
(The American Society of Mechanical Engineers (ASME), 1989)The onset of wrinkling of an unevenly stretched sheet metal subject to finite deformation is analyzed by an incremental finite element method. The sheet metal is modeled as a plate made of ... -
A Stochastic Nonlinear Constitutive Law for Concrete
(The American Society of Mechanical Engineers (ASME), 1989)An incremental three-dimensional stress-strain relationship for concrete with induced anisotropy has been developed. The nonlinearity and path-dependency are modeled by expressing the elastic moduli ... -
A Unified Constitutive Model for Cyclic Viscoplasticity and Its Applications to Various Stainless Steels
(The American Society of Mechanical Engineers (ASME), 1989)This paper deals with the monotonic and cyclic behavior of austenitic stainless steels and the way to model it. Developments made on constitutive equations led to elaborate sophisticated models ... -
Effects of Sub-Freezing Temperatures on Graphite/Epoxy Composite Materials
(The American Society of Mechanical Engineers (ASME), 1989)Moisture in composite materials has been the subject of considerable interest in the past decade. Many studies have shown that moisture directly causes damage in graphite/epoxy composite materials. ... -
Pressure Effects in Abrasive-Waterjet (AWJ) Machining
(The American Society of Mechanical Engineers (ASME), 1989)Abrasive-waterjets (AWJs) are formed by mixing high-pressure (up to 400 MPa) waterjets (0.1 to 1 mm in diameter) with abrasive particles in mixing tubes with typical 1/d ratios of 50 to 100. ... -
Slow Strain Rate Fracture Characteristics of Steel and Aluminum Alloys Tested in Mercury Environments
(The American Society of Mechanical Engineers (ASME), 1989)Slow strain rate tensile tests performed on Type 304 stainless steel, A516 Grade 70 C-Mn steel, and aluminum alloy 5083 revealed that all three materials were susceptible to varying degrees ... -
Similarity Analysis Applied to the Die Casting Process
(The American Society of Mechanical Engineers (ASME), 1989)Detailed studies of the filling process of the die with liquid metal and the solidification are necessary to put this technology on a firm scientific basis. An experimental study of the fluid ... -
Elastic-Plastic Compaction of a Two-Dimensional Assemblage of Particles
(The American Society of Mechanical Engineers (ASME), 1989)The influence of pore shape on the porosity-pressure behavior of powders undergoing compaction is studied theoretically and numerically. Idealized two-dimensional models are used to compare the ... -
Constitutive Modeling of Ratchetting Effects—Part II: Possibilities of Some Additional Kinematic Rules
(The American Society of Mechanical Engineers (ASME), 1989)The modeling possibilities of several linear and nonlinear-kinematic hardening rules are studied in detail in the particular case of tension-compression and in the framework of time-independent ... -
Subcritical Crack Growth Characteristics on Compact Type Specimens and Indentation Cracks in Glass
(The American Society of Mechanical Engineers (ASME), 1989)For the purpose of comparing crack growth characteristics on small indentation cracks with those for long cracks, subcritical crack growth data on soda-lime glass were obtained using the compact ... -
The Stiffening Effect of Rigid Elliptical Inclusions on a Power-Law Material
(The American Society of Mechanical Engineers (ASME), 1989)An approximate constitutive relation is derived for plane strain deformation in a power-law viscous matrix reinforced with long rigid inclusions with elliptical cross sections. The analysis is ... -
Stress-Strain Relations of SUS304 Stainless Steel After Cyclic Preloading
(The American Society of Mechanical Engineers (ASME), 1989)To formulate the constitutive equation for nonproportional cyclic loading, the influence of preloading on subsequent loading should be investigated experimentally. In this paper, both the stress-strain ... -
Growth of Short Fatigue Cracks at Notches in Woven Fiber Glass Reinforced Polymeric Composites
(The American Society of Mechanical Engineers (ASME), 1989)The fatigue crack initiation and growth characteristics of short cracks emanating from blunt notches with root radius varying from 1.6 to 6.35 mm at various depths in woven fiber-glass reinforced ... -
Simulation of the Variation of Strain Rates During a Rolling Pass in Compression Tests
(The American Society of Mechanical Engineers (ASME), 1989)A Nb-V steel’s response to constant true strain rate compression was compared to its behavior when the strain rate varied as during a rolling pass. The constitutive behavior during the two ... -
Constitutive Modeling of Ratchetting Effects—Part I: Experimental Facts and Properties of the Classical Models
(The American Society of Mechanical Engineers (ASME), 1989)The constitutive modeling of cyclic plasticity has made great progress during the past twenty years. One of the incompletely solved problems concerns ratchetting, that is the progressive strain ... -
The Influence of Test Temperature on the Ratchetting Behavior of Type 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1989)The zero-to-tension ratchetting behavior was investigated under uniaxial loading at room temperature and at 550, 600, and 650°C. In History I the maximum stress level of ratchetting was ... -
Elevated Temperature Low-Cycle Fatigue Strength of Butt Welded AISI 316 Steel Pipes
(The American Society of Mechanical Engineers (ASME), 1989)This paper reviews the experimental activities that were performed in recent years at the Department of Mechanical and Nuclear Engineering (DCMN) of the University of Pisa, mainly during research ...