Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2201-2220 of 3257
-
Comparison of Fatigue Tests of Two Plastics, Three Composites and an Aluminum Alloy Obtained on Four Different Types of Fatigue Machines
(The American Society of Mechanical Engineers (ASME), 1990)The results of fatigue tests of two thermoplastics (cellulose acetate and polystyrene), three composites (laminated plastics of paper, canvas, and fiberglass) and one aluminum alloy (25-ST) are ... -
Neutron Diffraction NDE for Advanced Composites
(The American Society of Mechanical Engineers (ASME), 1990)The strength and toughness of whisker- and fiber-reinforced composites are controlled to a large extent by the nature of the bonding between the fibers/whiskers and the matrix. An important ... -
Elasto-Viscoplastic Constitutive Equations for Clay and Its Application to Consolidation Analysis
(The American Society of Mechanical Engineers (ASME), 1990)The mathematical structure of Adachi and Oka’s model, a typical overstress type elasto-viscoplastic constitutive model, for normally consolidated clays is discussed. Since it has been recognized ... -
The Constitutive Equation for Silicon and Its Use in Crystal Growth Modeling
(The American Society of Mechanical Engineers (ASME), 1990)A stress analysis that describes the crystal growing process requires a material model that is valid over a wide temperature range and includes dislocation motion and multiplication. The stresses ... -
Prediction of Fatigue Life With and Without Hold Times Using the Chaboche Viscoplastic Constitutive Theory
(The American Society of Mechanical Engineers (ASME), 1990)The titanium alloy Ti-6Al-4V is known to exhibit creep behavior at temperatures as low as room temperature. Consequently, for cyclic loading with hold times it is possible that the rate dependent ... -
Creep Analysis of Beams and Arches Based on a Hereditary Visco-Elastic-Plastic Constitutive Law
(The American Society of Mechanical Engineers (ASME), 1990)An analytic study of planar beams and arches subjected to significant thermal cycling from ambient temperatures up to 800°C is presented. The study employs a recently unified nonlinear ... -
Enhancement Techniques for Ultrasonic Nondestructive Evaluation of Composite Materials
(The American Society of Mechanical Engineers (ASME), 1990)Conventional ultrasonic C-scanning sometimes produces distorted and degraded images due to a variety of reasons, including surface roughness, beam dispersion, extraneous noise and imperfect fidelity ... -
Quantitative NDE of Advanced Composites Using Ultrasonic Velocity Measurements
(The American Society of Mechanical Engineers (ASME), 1990)In this work, the use of ultrasonic velocity analysis for the quantitative nondestructive evaluation of the mechanical properties of composite laminates is discussed. The composite laminate is ... -
External Pressure Loading of Spiral Paper Tubes: Theory and Experiment
(The American Society of Mechanical Engineers (ASME), 1990)A closed-form elasticity solution is developed to predict stresses and strains in spiral paper tubes loaded axisymmetrically. No assumptions are made on stress distributions through the tube wall. ... -
Methods for Determining the Mode I and Mode II Fracture Toughness of Glass Using Thermal Stresses
(The American Society of Mechanical Engineers (ASME), 1990)The fracture toughness of soda-lime glass was measured by applying thermal stresses to center-cracked plates. Mode I cracking was achieved by chilling the crack faces. The stress intensity factor ... -
Friction and Wear Transitions of Materials: Break-in, Run-in, and Wear-in
(The American Society of Mechanical Engineers (ASME), 1990) -
Processing and Characterization of Multi-Layered Wear-Resistant Ceramic Coatings
(The American Society of Mechanical Engineers (ASME), 1990)A new concept of a multi-layered ceramic coating consisting of a porcelain enamel bond interlayer with thermal expansion characteristics tailored to match those of a cast iron substrate and a ... -
Processing and Characterization of Laser-Cladded Coating Materials
(The American Society of Mechanical Engineers (ASME), 1990)The feasibility of laser cladding as a surface modification process was experimentally investigated. Emphasis was placed on identification of the effects of independent critical process parameters ... -
Micromechanical Analysis of the Creep Response of Unidirectional Composites
(The American Society of Mechanical Engineers (ASME), 1990)The paper outlines the use of the micromechanics model proposed by Aboudi in predicting the creep response of unidirectional composites consisting of linearly viscoelastic matrices and elastic ... -
Tensile Strength of Stitching Joint in Woven Glass Fabrics
(The American Society of Mechanical Engineers (ASME), 1990)Stitching has been found to be able to improve the interlaminar strength of composite laminates. Its application as composite joining has been also explored. This study examined the tensile ... -
An Ultrasonic Technique for Testing the Orthotropic Symmetry of Polymeric Sheets by Measuring Their Elastic Shear Coupling Coefficients
(The American Society of Mechanical Engineers (ASME), 1990)An ultrasonic method, which allows the determination of the in-plane elastic stiffnesses of thin polymeric sheets, is described. The determination is complete, as it includes the shear coupling ... -
Creep Crack Growth in an Austenitic Cr-Ni-Mn Steel
(The American Society of Mechanical Engineers (ASME), 1990)Effects of grain-boundary sliding and strenthening by serrated grain boundaries on creep-crack growth are investigated using an austenitic 21Cr-4Ni-9Mn steel at 973 K in air. In surface notched ... -
Low Temperature Isothermal Strain in a Metastable Austenitic Stainless Steel Sheet
(The American Society of Mechanical Engineers (ASME), 1990)Low temperature stationary creep strain in a metastable austenitic stainless steel was studied at −162°C under various combinations of prestrain and stress ratio. It was found that the ... -
A Bilinear Constitutive Model for Isotropic Bimodulus Materials
(The American Society of Mechanical Engineers (ASME), 1990)Proper formulation of stress-strain relations, particularly in tension-compression situations for isotropic biomodulus materials, is an unresolved problem. Ambartsumyan’s model [8] and Jones’ weighted ... -
Creep After Cyclic-Plasticity Under Multiaxial Conditions for Type 316 Stainless Steel at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1990)History effects of cyclic-plasticity on subsequent creep have been elucidated for type 316 stainless steel at 600°C under multiaxial states of stress. Tension-compression and circular strain ...