Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1421-1440 of 3257
-
A Unified Bifurcation Analysis of Sheet Metal Forming Limits
(The American Society of Mechanical Engineers (ASME), 2001)The purpose of this study is to determine analytically the orientations of localized necks occurring in sheet metal forming processes, and obtain the corresponding forming limit diagrams (FLDs). ... -
Improvement of Vibration Damping Capacity and Fracture Toughness in Composite Laminates by the Use of Polymeric Interleaves
(The American Society of Mechanical Engineers (ASME), 2001)It is shown that, under certain conditions, simultaneous improvement of vibration damping capacity and interlaminar fracture toughness in composite laminates can be achieved by using polymeric ... -
Micro-Structural Analysis of Chip Formation During Orthogonal Machining of Al/SiCp Composites
(The American Society of Mechanical Engineers (ASME), 2001)Discontinuously Reinforced Aluminum (DRA) Composites form unique case from the research in metal cutting point of view. Reinforcement in these materials acts as “macroscopic” and “isolated” ... -
Mid-Wall Temperature in an Eroded Section of an Austenitic Superheater/Reheater Tube
(The American Society of Mechanical Engineers (ASME), 2001)Superheater and reheater tubes in a fossil-fuelled boiler are subjected to erosion and corrosion that cause the tubes to lose their thickness in a localized manner. To avoid unscheduled tube ... -
Assessment of Sandwich Beam in Three-Point Bending for Measuring Adhesive Shear Modulus
(The American Society of Mechanical Engineers (ASME), 2001)A finite element analysis (FEA) was conducted to examine the feasibility of determining the shear modulus of an adhesive in a bonded geometry using a three-point bending test on a sandwich ... -
Modeling Studies to Predict Stresses in Composite Floor Tubes of Black Liquor Recovery Boilers
(The American Society of Mechanical Engineers (ASME), 2001)The results of finite element modeling studies to analyze the composite floor tubes of recovery boilers used by the pulp and paper industry are presented. Thermal and mechanical analyses have ... -
A Study of Beta Processing of Ti-6Al-4V: Is it Trivial?
(The American Society of Mechanical Engineers (ASME), 2001)Deformation of Ti-6Al-4V alloy in the β phase field is generally considered to be trivial since the material is highly workable at these temperatures and does not normally pose problems during ... -
Analysis and Testing of Indentation Fracture Behavior of Piezoelectric Ceramics Under an Electric Field
(The American Society of Mechanical Engineers (ASME), 2001)To estimate the electric fracture toughness, indentation fracture (IF) tests were made on piezoelectric materials under combined mechanical and electrical loads. Lead zirconate titanate (PZT) ... -
A Constitutive Description of Aluminum-1% Magnesium Alloy Deformed Under Hot-Working Conditions
(The American Society of Mechanical Engineers (ASME), 2001)A constitutive description of the deformation of commercial aluminum-1% magnesium alloy (AA5005) under hot working conditions has been formulated on a rational basis. The strain dependence of the ... -
Computer Identification of Structural Weaknesses in Locally Anisotropic Polycrystalline Materials
(The American Society of Mechanical Engineers (ASME), 2001)Computer experiments were performed to investigate behavior of mesoscopic stress responses in a simulated polycrystalline material sample containing a fairly large number of constituent grains for ... -
Off-Axis Torsion Tests on Tubular Specimens of Steel
(The American Society of Mechanical Engineers (ASME), 2001)In order to analyze the anisotropic hardening behavior of metals, an off-axis torsion test by combined loading is developed. In this test, the maximum shear stress direction φ can be changed ... -
Real-Time Process Characterization of Open Die Forging for Adaptive Control
(The American Society of Mechanical Engineers (ASME), 2001)Open die forging is a process in which products are made through repeated, incremental plastic deformations of a workpiece. Typically, the workpiece is held by a manipulator, which can position ... -
Superimposing Ultrasonic Waves on the Dies in Tube and Wire Drawing
(The American Society of Mechanical Engineers (ASME), 2001)The forces during wire and tube drawing can be reduced by ultrasonically oscillating dies. It is a major problem of conventional wire and tube drawing to introduce high forces into the forming ... -
A Finite Element Based Die Design Algorithm for Sheet-Metal Forming on Reconfigurable Tools
(The American Society of Mechanical Engineers (ASME), 2001)Tooling cost is a major contributor to the total cost of small-lot production of sheet metal components. Within the framework of an academic/industrial/government partnership devoted to the ... -
Improving Formability in Sheet Metal Stamping With Active Drawbead Technology
(The American Society of Mechanical Engineers (ASME), 2001)Aluminum is expected to gain popularity as material for the bodies of the next generation of lighter and more fuel-efficient vehicles. However, its lower formability compared with that of steel ... -
Identification of Hardening Parameters of Metals From Spherical Indentation Tests
(The American Society of Mechanical Engineers (ASME), 2001)The identification method of hardening parameters specifying stress-strain curve is proposed by applying spherical indentation test and measuring the penetration depth during loading and unloading. ... -
Effect of Loading Rate on Fracture Morphology in a High Strength Ductile Steel
(The American Society of Mechanical Engineers (ASME), 2001)Fracture experiments in a high-strength ductile steel (2.3Ni-1.3Cr-0.17C) were conducted under static and dynamic loading conditions in a three-point bend and a one-point bend configurations. A ... -
Constitutive Relations for Inelastic Deformation and Damage Accumulation in Hard Alpha Titanium
(The American Society of Mechanical Engineers (ASME), 2001)The constitutive properties of hard alpha Ti were recently generated by Chan et al., 2000, “Constitutive Properties of Hard Alpha Titanium,” Metall. and Maters. Trans. A, Vol. 31A, pp. 3029–3040, ... -
An Experimental Study of Inhomogeneous Cyclic Plastic Deformation
(The American Society of Mechanical Engineers (ASME), 2001)A localized inhomogeneous cyclic plastic deformation phenomenon was experimentally investigated in a mild steel. Small strain gages were utilized to characterize the local deformation within the ... -
Material Properties of Aluminum Alloy for Accurate Draw-Bend Simulation
(The American Society of Mechanical Engineers (ASME), 2001)The main objective of this paper is to simulate springback using a combined kinematic/isotropic hardening model. Material parameters in the hardening model are identified by an inverse method. ...