Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1301-1320 of 3257
-
Forming Limit Analysis of Sheet Metals Based on a Generalized Deformation Theory
(The American Society of Mechanical Engineers (ASME), 2003)This paper presents the development of a generalized method to predict forming limits of sheet metals. The vertex theory, which was developed by Stören and Rice (1975) and recently simplified ... -
The Computation and Measurement of Residual Stresses in Laser Deposited Layers
(The American Society of Mechanical Engineers (ASME), 2003)Laser metal forming is an attractive process for rapid prototyping or the rebuilding of worn parts. However, large tensile stress may arise in layers deposited by laser melting of powder. A ... -
Mechanical Characterization of a CVD Diamond Coating by Nanoindentation Test
(The American Society of Mechanical Engineers (ASME), 2003)A FEM analysis was carried out to study the mechanical behavior of a hard coating subjected to a nanoindentation test performed with a Berkovich indenter. The nanoindentation test was simulated ... -
Investigation Into Cumulative Damage Rules to Predict Fretting Fatigue Life of Ti-6Al-4V Under Two-Level Block Loading Condition1
(The American Society of Mechanical Engineers (ASME), 2003)The effects of variable amplitude loading on fretting fatigue behavior of titanium alloy, Ti-6Al-4V were examined. Fretting fatigue tests were carried out under constant stress amplitude and three ... -
Finite Element Modeling of Chip Formation in the Domain of Negative Rake Angle Cutting
(The American Society of Mechanical Engineers (ASME), 2003)A thermo-elastic-plastic finite element modeling of orthogonal cutting with a large negative rake angle has been developed to understand the mechanism and thermal aspects of grinding. A stagnant ... -
Evaluation Method for Fatigue Strength of FRP/Metal Adhesive Joints Considering Mean Stress
(The American Society of Mechanical Engineers (ASME), 2003)The fatigue strength of two types of FRP/metal adhesive joints at low temperature, a double lap joint and an embedded joint, was evaluated analytically and experimentally. First, the stress ... -
The Effect of Graded Strength on Damage Propagation in Continuously Nonhomogeneous Materials
(The American Society of Mechanical Engineers (ASME), 2003)A damage model developed by Johnson and Holmquist is implemented into a dynamic finite element code. This is then used to study the effect of grading of the phenomenological damage parameters ... -
Sheet Metal Forming Using Polymer Composite Rapid Prototype Tooling
(The American Society of Mechanical Engineers (ASME), 2003)To meet the growing demand for rapid, low-cost die fabrication technology in the sheet metal forming industry, easy-to-machine, polyurethane-based, composite board stock is widely used as a rapid ... -
Errata: “New Estimation Method of Fatigue Properties of Aluminum Alloys” [ASME Journal of Engineering Materials and Technology, 2003, Vol. 125, No. 2, pp. 208–214]
(The American Society of Mechanical Engineers (ASME), 2003)Equation (14) on page 212 should read as follows: Display Formulaεa=σB+335E (2Nf)−1/6 [(σB+335)/0.446σB]+εf(2Nf)−0.664 -
Effects of Temperature and Moisture on the High Strain Rate Compression Response of Graphite/Epoxy Composites
(The American Society of Mechanical Engineers (ASME), 2003)Experimental investigations were carried out on unidirectional Graphite/Epoxy laminate samples under dynamic compression loading using a modified Split Hopkinson Pressure Bar. High strain rate testing ... -
Spatially Averaged Local Strains in Textile Composites Via the Binary Model Formulation
(The American Society of Mechanical Engineers (ASME), 2003)A previously published computational model of textile composites known as the Binary Model is generalized to allow systematic study of the effects of mesh refinement. Calculations using different ... -
Control of Damage in Composite Laminates by Ply-Stacking Designs: Characteristic Failure Signatures and Safety Criteria
(The American Society of Mechanical Engineers (ASME), 2003)Structural designs for composite laminated systems can be optimized for a fail-safe in-service performance by introducing the built-in cumulative-damage-indicators for the progressive degradation of ... -
Statistical Analysis of Experimental Parameters in Continuous Indentation Tests Using Taguchi Method
(The American Society of Mechanical Engineers (ASME), 2003)The continuous indentation test, which applies an indentation load to a material and records the indentation depth, yields indentation tensile properties whose accuracy can vary depending on such ... -
Elastic and Inelastic Recovery After Plastic Deformation of DQSK Steel Sheet
(The American Society of Mechanical Engineers (ASME), 2003)Strain recovery after plastic prestrain and associated elastic and inelastic behavior during loading and unloading of DQSK steel sheet are measured. Average tangent modulus and Poisson’s ratio ... -
Effect of Laser Pre-Treatment on the Machining Performance of Aluminum/SiC MMC
(The American Society of Mechanical Engineers (ASME), 2003)Although the abrasive reinforcement in MMCs primarily controls their machining behavior, the properties of the matrix also exert an influence. A 1200 W diode laser was used, due to the large ... -
Spatial Impact of a Slender Beam
(The American Society of Mechanical Engineers (ASME), 2003)In this paper, the dynamics of the spatial impact of a slender beam is analyzed. The equations of motion are calculated using Kane’s impact method. The generalized momentum and generalized ... -
Nanoindentation Measurements on Low-k Porous Silica Thin Films Spin Coated on Silicon Substrates
(The American Society of Mechanical Engineers (ASME), 2003)MEMS (MicroElectroMechanical Systems) are composed of thin films and composite nanomaterials. Although the mechanical properties of their constituent materials play an important role in controlling ... -
Assessment of the Fracture Behavior of an Asymmetrically Loaded Cantilever Composite Structure
(The American Society of Mechanical Engineers (ASME), 2003)The complex fracture behavior of a cross-ply composite cantilever beam with artificially embedded delamination is investigated analytically, numerically, and experimentally. The analysis of the ... -
Surface Modification of Powder Metallurgy Components With a Direct Diode Laser
(The American Society of Mechanical Engineers (ASME), 2003)A 1200 W diode laser was used to modify the surface properties of a fully-sintered ferrous PM material. Two modifications were investigated; transformation hardening of selected areas and sealing ... -
On the Mechanical Response in a Thermal Barrier System Due to Martensitic Phase Transformation in the Bond Coat
(The American Society of Mechanical Engineers (ASME), 2003)Recent studies have shown that Pt-aluminide—a common bond coat material in thermal barrier coatings—undergoes martensitic transformations during thermal cycling. The transformations are associated ...