Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1281-1300 of 3257
-
A Closure Model to Crack Growth Under Large-Scale Yielding and Through Residual Stress Fields
(The American Society of Mechanical Engineers (ASME), 2003)This paper presents a closure model for predicting the growth behavior of short cracks in the presence of large-scale yielding and residual compressive stresses, representative of structures that ... -
Surface Enhancement of Al2O3 Fiber With Nanosized Al2O3 Particles Using A Dry Mechanical Coating Process
(The American Society of Mechanical Engineers (ASME), 2003)Currently, fabrication of composite materials is of great interest in industry. By combining materials of different properties, we can produce new composite materials with synergetic functionality ... -
Implementation of a Viscoplastic Model for a Plasma Sprayed Ceramic Thermal Barrier Coating
(The American Society of Mechanical Engineers (ASME), 2003)This paper describes the implementation and modification of a previously proposed unified viscoplastic constitutive model to simulate the behavior of a Yttria Stabilized Zirconia plasma sprayed ... -
An Approximate Method of Estimating the Yield of a Strip Under Tension Cut by Serrated Surfaces on Opposite Faces
(The American Society of Mechanical Engineers (ASME), 2003)In view of the well-known disparity between predictions from temper rolling models and measured values from rolling mills, there is a need to obtain a better understanding of the effect of ... -
New Estimation Method of Fatigue Properties of Aluminum Alloys
(The American Society of Mechanical Engineers (ASME), 2003)A new method on estimating fatigue properties from simple tensile data was proposed for aluminum alloys. The method is based on experimental strain-life curves. An optimization technique was ... -
Optimization of Directionally Attached Piezoelectric Actuators
(The American Society of Mechanical Engineers (ASME), 2003)A directionally attached piezoelectric (DAP) actuator is one method to control the twisting vibration of a plate with high authority. Although insuring proper performance for DAP actuators has ... -
Measurement of In-Plane Residual Stresses Varying With Depth by the Interferometric Strain/Slope Rosette and Incremental Hole-Drilling
(The American Society of Mechanical Engineers (ASME), 2003)A new experimental method utilizing the Interferometric Strain/Slope Rosette (ISSR) and incremental hole-drilling is applied to measure in-plane residual stresses which vary with depth. For each ... -
On the Improvement of Calibration Coefficients for Hole-Drilling Integral Method: Part II—Experimental Validation of Calibration Coefficients
(The American Society of Mechanical Engineers (ASME), 2003)Experimental validation of the calibration coefficients for integral hole-drilling method obtained from an improved three-dimensional FEM model was achieved using bending test of a cantilever beam. ... -
Experimental Implementation of Neural Network Springback Control for Sheet Metal Forming
(The American Society of Mechanical Engineers (ASME), 2003)The forming of sheet metal into a desired and functional shape is a process, which requires an understanding of materials, mechanics, and manufacturing principles. Furthermore, producing consistent ... -
Simulating Distortion and Residual Stresses in Carburized Thin Strips
(The American Society of Mechanical Engineers (ASME), 2003)This paper illustrates the application of a new multiphase material model for simulating distortion and residual stresses in carburized and quenched gear steels. Simulation is focused on thin, ... -
Ultimate Strength and Failure Mechanism of Resistance Spot Weld Subjected to Tensile, Shear, or Combined Tensile/Shear Loads
(The American Society of Mechanical Engineers (ASME), 2003)Strength tests were performed to reveal the failure mechanisms of spot weld in lap-shear and cross tension test samples. It is shown the while the lap-shear (cross tension) sample is subjected ... -
Analysis of Tube Free Hydroforming Using an Inverse Approach With FLD-Based Adjustment of Process Parameters1
(The American Society of Mechanical Engineers (ASME), 2003)This paper describes an inverse approach (IA) formulation for the analysis of tubes under free hydroforming conditions. The IA formulation is derived from that of Guo et al. established for ... -
Measurement of Thickness-Average Residual Stress Near the Edge of a Thin Laser Peened Strip
(The American Society of Mechanical Engineers (ASME), 2003)This paper presents measurements of the thickness-average residual stress imposed by laser peening near the edge of a thin sheet of a common titanium alloy. The slitting (or crack compliance) ... -
Finite Element Modeling of Superplastic Sheet Metal Forming for Cavity Sensitive Materials
(The American Society of Mechanical Engineers (ASME), 2003)In this paper, a constitutive equation for superplasticity, which is based on the microstructural mechanism of superplastic deformation taking into account the effects of deformation damage, is ... -
Investigation of Nanomechanical Properties of the Interphase in a Glass Fiber Reinforced Polyester Composite Using Nanoindentation
(The American Society of Mechanical Engineers (ASME), 2003)Glass fiber reinforced polymer composites are widely used as structural materials. These two-component materials can be tailored to suit a large variety of applications. A better understanding ... -
Modeling of Fatigue Crack Propagation During Sliding Wear of Polymers
(The American Society of Mechanical Engineers (ASME), 2003)The propagation of a crack initiating at the surface was analyzed to simulate the fatigue wear behavior of glassy polymer materials. A crack in a material half plane was assumed to propagate ... -
Long-Term Reliability of Brittle Materials: The Issue of Crack Arrest
(The American Society of Mechanical Engineers (ASME), 2003)In structures containing brittle materials, residual and/or heterogenous stresses may prevent cracks to propagate up to failure. Consequently, for such structures, crack arrest has to be accounted ... -
One-Dimensional Dynamic Compressive Behavior of EPDM Rubber
(The American Society of Mechanical Engineers (ASME), 2003)Dynamic compressive stress-strain curves at various strain rates of an Ethylene-Propylene-Diene Monomer Copolymer (EPDM) rubber have been determined with a modified split Hopkinson pressure bar ... -
Kinetics of Diffusional Phase Transformation in Multicomponent Elastic-Plastic Materials
(The American Society of Mechanical Engineers (ASME), 2003)The goal of this paper is to derive a micromechanics framework to study the kinetics of transformation due to interface migration in elastic-plastic materials. Both coherent and incoherent ... -
Estimation of Steady-State Creep Behavior of Al2O3/YAG Eutectic Composite by Image-Based Finite Element Analysis
(The American Society of Mechanical Engineers (ASME), 2003)Al2O3/YAG eutectic composite has been developed for a structural material used in ultra high temperature environments over 1500°C such as a gasturbine. Creep behavior is one of the important ...