Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1161-1180 of 3257
-
Deformation Behavior of Cold Upset Forming of Sintered Al-Fe Composite Preforms
(The American Society of Mechanical Engineers (ASME), 2005)Cold upsetting experiments were carried out on sintered Al–Fe preforms in order to evaluate their deformation characteristics. The effects of iron content and initial fractional density of the ... -
Numerical Analysis of Electrodeposited Nickel Coating in Multistage Drawing Processes
(The American Society of Mechanical Engineers (ASME), 2005)The elastic-plastic finite element method of a dynamic explicit algorithm was used to simulate the deep drawing processes of nickel coating electrodeposited on a steel substrate to form an ... -
Effects of Inclusions and Microstructures on Impact Energy of High Heat-Input Submerged-Arc-Weld Metals
(The American Society of Mechanical Engineers (ASME), 2005)Submerged-arc-weld metal made with variations of heat-input and consumables were examined to study the inclusions and their effects on the Charpy impact energy of the weld metal as a measure ... -
Multiscale Model to Study the Effect of Interfaces in Carbon Nanotube-Based Composites
(The American Society of Mechanical Engineers (ASME), 2005)In order to fully harness the outstanding mechanical properties of carbon nanotubes (CNT) as fiber reinforcements, it is essential to understand the nature of load transfer in the fiber matrix ... -
Experimental and Numerical Evaluation of Crack Arresting Capability Due to a Dimple
(The American Society of Mechanical Engineers (ASME), 2005)Crack arresting capability is experimentally examined using center cracked tension specimens and varying the placement of the dimple ahead of the crack tip. It is confirmed that the dimple gives ... -
Using Embossing to Create a Fiber Reinforced Honeycomb Composite
(The American Society of Mechanical Engineers (ASME), 2005)This research project used hot embossing to create a strong and tough polymeric based composite structure. A honeycomb type structure was created by pressing small grooves into thin polycarbonate ... -
Mesodamage Evolution in Polycrystals
(The American Society of Mechanical Engineers (ASME), 2005)A micromechanical model of damaged elasto-inelastic behavior is proposed to predict the plastic fatigue life for fcc metallic polycrystals under multiaxial loading paths. This model is expressed ... -
Mechanical Properties of Kevlar® KM2 Single Fiber
(The American Society of Mechanical Engineers (ASME), 2005)Kevlar® KM2 fiber is a transversely isotropic material. Its tensile stress-strain response in the axial direction is linear and elastic until failure. However, the overall deformation in the ... -
Mathematical Modeling of Ultra-High-Pressure Waterjet Peening
(The American Society of Mechanical Engineers (ASME), 2005)Waterjet peening is a recent promising method in surface treatment. It has the potential to induce compressive residual stresses that benefit the fatigue life of materials similar to the ... -
Special Section on Fatigue of Advanced Materials
(The American Society of Mechanical Engineers (ASME), 2005)In recent years, the mechanistic understanding of the fatigue behavior of advanced materials has continued to emerge. Some of the systems that have been examined include: biomaterials, cellular ... -
A New Analytical Approach for Hole Drilling Residual Stress Analysis by Full Field Method
(The American Society of Mechanical Engineers (ASME), 2005)Most of the full field methods for residual stress investigation combine an optical interferometric technique (grating interferometry, speckle interferometry, holographic interferometry) with the ... -
A Mechanistic Approach to Matrix Cracking Coupled with Fiber–Matrix Debonding in Short-Fiber Composites
(The American Society of Mechanical Engineers (ASME), 2005)A micro–macro mechanistic approach to damage in short-fiber composites is developed in this paper. At the microscale, a reference aligned fiber composite is considered for the analysis of the ... -
Fatigue Crack Identification in Tensile-Shear Spot Welded Joints by Dynamic Response Characteristics
(The American Society of Mechanical Engineers (ASME), 2005)A theoretical model for the estimation of fatigue crack length of tensile-shear spot welded specimen is developed which incorporates the natural frequency and mode variation. The model is based ... -
Relaxation of Peening Residual Stresses Due to Cyclic Thermo-Mechanical Overload
(The American Society of Mechanical Engineers (ASME), 2005)Shot-peening induced residual stresses can be relaxed due to cyclic loading. This relaxation plays an important role in determining the fatigue life of the peened components. It is therefore ... -
Formability and Weld Zone Analysis of Tailor-Welded Blanks for Various Thickness Ratios
(The American Society of Mechanical Engineers (ASME), 2005)Cold-rolled steel sheets of thicknesses ranging from 0.5 to 1.0 mm were used to produce tailor-welded blanks (TWBs) with various thickness ratios. In this study, the formability of the TWBs, ... -
The New Grain Formation During Warm and Hot Deformation of Copper
(The American Society of Mechanical Engineers (ASME), 2005)Initial stage of dynamic recrystallization (DRX) under warm and hot deformation was investigated in polycrystalline copper. At the onset of DRX at intermediate deformation temperatures (i.e., high ... -
Optimizing the Ogden Strain Energy Expression of Rubber Materials
(The American Society of Mechanical Engineers (ASME), 2005)The Ogden strain energy expression is expanded to an optimal number of terms characterizing materials to predict any response of any mode of deformation well. The effect of each term generating ... -
Thermomechanical Fatigue Behavior of a Directionally Solidified Ni-Base Superalloy
(The American Society of Mechanical Engineers (ASME), 2005)A continuum crystal plasticity model is used to simulate the material behavior of a directionally solidified Ni-base superalloy, DS GTD-111, in the longitudinal and transverse orientations. ... -
The Effect of Mean Stress on the Fatigue Behavior of Woven-Roving Glass Fiber-Reinforced Polyester Subjected to Torsional Moments
(The American Society of Mechanical Engineers (ASME), 2005)The effect of torsional mean stress on the fatigue behavior of glass fiber-reinforced polyester (GFRP) is studied by testing thin-walled, woven-roving tubular specimens with two fiber orientations, ... -
Monte Carlo Simulation of Particle-Cracking Damage Evolution in Metal Matrix Composites
(The American Society of Mechanical Engineers (ASME), 2005)In the modeling of microstructural damage mechanisms of composites, damage evolution plays an important role and has significant effects on the overall nonlinear behavior of composites. In this ...