Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1081-1100 of 3257
-
Size Effect on Compressive Strength of Sandwich Panels with Fracture of Woven Laminate Facesheet
(The American Society of Mechanical Engineers (ASME), 2006)Prismatic sandwich specimens of various sizes, geometrically scaled in the ratio 1:2:4:8, are subjected to eccentric axial compression and tested to failure. The sandwich core consists of a ... -
Magnetorheological Fluid Behavior Under Constant Shear Rates and High Magnetic Fields Over Long Time Periods
(The American Society of Mechanical Engineers (ASME), 2006)This paper presents a new magnetorheological (MR) cell design along with a study of the magnetic field, shear rate, and time/shear strain influences on the properties and behavior of a MR ... -
Effect of Oxygen Content on the Processing Maps for Hot Deformation of OFHC Copper
(The American Society of Mechanical Engineers (ASME), 2006)Processing map for the hot deformation of high purity oxygen free high conductivity (OFHC) copper (2ppm oxygen) has been developed in the temperature range 600–950°C and strain rate range ... -
Effect of Cryogenic Temperature on the Fracture Toughness of Graphite/Epoxy Composites
(The American Society of Mechanical Engineers (ASME), 2006)The research presented in this paper is an effort to better understand the interlaminar fracture behavior of graphite/epoxy composite laminates in cryogenic conditions. Double cantilever beam tests ... -
Creep-Induced Microstructural Change in 304-Type Austenitic Stainless Steel
(The American Society of Mechanical Engineers (ASME), 2006)We studied microstructure changes of 304-type austenitic stainless steel subjected to a tensile stress at 973K. We monitored the shear-wave attenuation and velocity using electromagnetic acoustic ... -
Instrumented Microindentation of Nanoporous Alumina Films
(The American Society of Mechanical Engineers (ASME), 2006)We examine the mechanical behavior of anodic alumina thin films with organized nanometer-scale porosity. The cylindrical pores in the alumina film are arranged perpendicular to the film thickness ... -
Investigation into Tangential Force and Axial Stress Effects on Fretting Fatigue Behavior
(The American Society of Mechanical Engineers (ASME), 2006)Fretting fatigue behavior of a titanium alloy was investigated using a dual actuator test setup which was capable to apply the pad displacement independent of the applied cyclic load on specimen. ... -
Local Stress-Ratio Criterion for Incremental Hole-Drilling Measurements of Shot-Peening Stresses
(The American Society of Mechanical Engineers (ASME), 2006)A criterion to evaluate the influence of the so-called plasticity effect on the final outcome of the incremental hole-drilling technique (IHD), for measuring residual stresses induced by mechanical ... -
Identification of Small-Sized Cracks on Cross-Stiffened Plate Structures for Ships
(The American Society of Mechanical Engineers (ASME), 2006)In this paper we discuss the results of experimental and numerical studies carried out for monitoring the integrity of a 1∕20th model of the side shell of a ship’s structure, using its ... -
Creep-Fatigue Life Evaluation for Sn-3.5Ag Solder
(The American Society of Mechanical Engineers (ASME), 2006)This paper studies the creep-fatigue life evaluation of Sn-3.5Ag solder under push-pull loading using fast-fast, fast-slow, slow-fast, slow-slow, and strain-hold strain waves. Extensive creep-fatigue ... -
An Approximated Harmonic Balance Method for Nonlinear Vibration of Viscoelastic Structures
(The American Society of Mechanical Engineers (ASME), 2006)In this paper, we deal with the nonlinear vibration of viscoelastic shell structures. Coupling an approximated harmonic balance method with one mode Galerkin’s procedure, one obtains an amplitude ... -
Shape Memory Alloys Cyclic Behavior: Experimental Study and Modeling
(The American Society of Mechanical Engineers (ASME), 2006)Shape memory alloys (SMA) are good candidates for being integrated in composite laminates where they can be used as passive dampers, strain sensors, stiffness or shape drivers. In order to ... -
Partial Hyperbolic-Tangent Friction Element Based Phenomenological Models for Shape Memory Alloy Pseudoelastic Hysteresis
(The American Society of Mechanical Engineers (ASME), 2006)A new mechanism-based phenomenological model, comprising linear and nonlinear springs and a nonlinear friction element, is presented for the pseudoelastic damping behavior of shape memory alloys. ... -
Multiscale Thermodynamic Significance of the Scale Invariance Approach in Continuum Inelasticity
(The American Society of Mechanical Engineers (ASME), 2006)In this paper, the scale invariance approach from micro- to macro-plasticity by (1995, “From Micro- to Macro-plasticity: The Scale Invariance Approach,” ASME J. Eng. Mater., 117, pp. 352–355) ... -
Using a Dovetail Fixture to Study Fretting Fatigue and Fretting Palliatives
(The American Society of Mechanical Engineers (ASME), 2006)Fretting fatigue damage can reduce the service life of engineering components in contact. The attachment between blades and disks in the fan and compressor stages of gas turbine engines is ... -
Micromechanical Modeling of Particulate Composites for Damping of Acoustic Waves
(The American Society of Mechanical Engineers (ASME), 2006)The self-consistent (SC) micromechanical model of a composite containing coated micro-inclusions, originally proposed in the static regime by (1994, J. Eng. Mater. Technol., 116, 274–278), is ... -
Stress-Strain-Temperature Behavior Due to B2-R-B19′ Transformation in NiTi Polycrystals
(The American Society of Mechanical Engineers (ASME), 2006)Thermomechanical behavior of superelastic NiTi wires undergoing sequential B2-R-B19′ martensitic transformation was investigated by two recently developed in-situ experimental methods (in-situ neutron ... -
A Phenomenological Model for Superelastic NiTi Wires Based on Plasticity With Focus on Strain-Rate Dependency Caused by Temperature
(The American Society of Mechanical Engineers (ASME), 2006)A simple one-dimensional model has been developed to illustrate methods to account for transformation bands in plasticity-based models. Austenite-martensite and martensite-austenite transformations ... -
Measurement and Prediction of the Residual Stress Field Generated by Side-Punching
(The American Society of Mechanical Engineers (ASME), 2006)Side-punching is proposed as a method of introducing a well-defined residual stress field into a laboratory-sized test specimen. Such a specimen may subsequently be used to assess the influence ... -
Combustion Synthesis of a Functionally Graded NiTi-TiCx Composite
(The American Society of Mechanical Engineers (ASME), 2006)Combustion synthesis (CS) is an alternative technique for producing advanced materials and is dependent upon a highly exothermic chemical reaction to become self-sustaining after only a short ...