Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1061-1080 of 3257
-
Buckling Analysis of Delaminated and Stitched Composite Plate System Under Hygrothermal Pressure
(The American Society of Mechanical Engineers (ASME), 2006)In this study, we develop a model for buckling of a partially delaminated composite plate with transverse stitching to resist out of plane deformations. The model applies to carbon fiber/polyimide ... -
Analysis of Interfacial Debonding in Three-Dimensional Composite Microstructures
(The American Society of Mechanical Engineers (ASME), 2006)This paper is aimed at analyzing stresses and fiber-matrix interfacial debonding in three-dimensional composite microstructures. It incorporates a 3D cohesive zone interface model based element to ... -
Modeling Thermo-Oxidative Layer Growth in High-Temperature Resins
(The American Society of Mechanical Engineers (ASME), 2006)This paper describes modeling of degradation behavior of high-temperature polymers under thermo-oxidative aging conditions. Thermo-oxidative aging is simulated with a diffusion-reaction model in which ... -
Compression of Packed Particulate Systems: Simulations and Experiments in Graphitic Li-ion Anodes
(The American Society of Mechanical Engineers (ASME), 2006)Increased thermal conductivity, electronic conductivity, and reversible capacity (i.e., reduced irreversible capacity loss, or ICL) have been demonstrably achievable by compression of anodes into ... -
Amorphous and Semicrystalline Solid Polymers: Experimental and Modeling Studies of Their Inelastic Deformation Behaviors
(The American Society of Mechanical Engineers (ASME), 2006)The study of the inelastic deformation behavior of six amorphous and semicrystalline polymers was performed to develop and verify the capabilities of a constitutive material model. The test ... -
Post-Curing Effects on Marine VARTM FRP Composite Material Properties for Test and Implementation
(The American Society of Mechanical Engineers (ASME), 2006)Structural composites are increasingly being utilized in many large naval and civil structures where it is vital that their long-term performance be predictable and their variability definable ... -
A Thermodynamic Framework for Describing Solidification of Polymer Melts
(The American Society of Mechanical Engineers (ASME), 2006)A thermodynamic framework is presented that can be used to describe the solidification of polymer melts, both the solidification of atactic polymers into an amorphous elastic solid and the ... -
Steam Pressure Generated in a Spherical Cavity in a Moisture Saturated Polymer Matrix Composite during Rapid Heating
(The American Society of Mechanical Engineers (ASME), 2006)The time history of steam pressure inside an isolated spherical micro-cavity in a polymer matrix composite is studied by assuming that the chemical potential of water is continuous across the ... -
Fiber Composite Strength Modeling With Extension to Life Prediction
(The American Society of Mechanical Engineers (ASME), 2006)This paper focuses on the probability modeling of fiber composite strength, wherein the failure modes are dominated by fiber tensile failures. The probability model is the tri-modal local ... -
Differential Implementation of the Viscoelastic Response of a Curing Thermoset Matrix for Composites Processing
(The American Society of Mechanical Engineers (ASME), 2006)The ability to manufacture thermoset matrix composite materials into large and complex structures can be significantly enhanced by modeling the behavior of the system during the process. As a ... -
Computational Micromechanics for High-Temperature Constitutive Equations of Polymer-Matrix Composites With Oxidation Reaction, Damage, and Degradation
(The American Society of Mechanical Engineers (ASME), 2006)The proper determination of high-temperature constitutive properties and damage of polymer-matrix composites (PMC) in an aggressive environment is critical in high-speed aircraft and propulsion ... -
Analysis of Shadow Mask Tension Subjected to Thermal and Mechanical Loads
(The American Society of Mechanical Engineers (ASME), 2006)In cathode ray tubes, a tension is imposed into the shadow mask during manufacturing to avoid slight variations in the position due to in service temperatures or deformation. Initially, tension ... -
Determination of Mode of Damage During Creep-Fatigue Interaction
(The American Society of Mechanical Engineers (ASME), 2006)A technique has been developed using the reversing dc electrical potential method to determine the mode of damage taking place during creep-fatigue interaction. It is observed that the hysteresis ... -
Self-Folding and Unfolding of Carbon Nanotubes
(The American Society of Mechanical Engineers (ASME), 2006)Carbon nanotubes (CNTs) constitute a prominent example of nanomaterials. In most studies on mechanical properties, the effort was concentrated on CNTs with relatively small aspect ratio of length ... -
Preface
(The American Society of Mechanical Engineers (ASME), 2006)This special issue of the Journal of Engineering Materials and Technology contains 15 papers delivered at the Symposium on Time-Dependent Behaviors of PMCs (Polymer Matrix Composites) and Polymers, ... -
Cohesive Layer Modeling of Time-Dependent Debond Growth in Aggressive Environments
(The American Society of Mechanical Engineers (ASME), 2006)The objective of this paper is to model the synergistic bond-degradation mechanisms that may occur at the interface between a fiber-reinforced polymer (FRP) that is adhesively bonded to a ... -
Damage-Induced Modeling of Elastic-Viscoelastic Randomly Oriented Particulate Composites
(The American Society of Mechanical Engineers (ASME), 2006)This paper presents a model for predicting the damage-induced mechanical response of particle-reinforced composites. The modeling includes the effects of matrix viscoelasticity and fracture, both ... -
A Constitutive Model for Strain-Induced Crystallization in Poly(ethylene terephthalate) (PET) during Finite Strain Load-Hold Simulations
(The American Society of Mechanical Engineers (ASME), 2006)Recently, a hyperelastic-viscoplastic constitutive model was developed for PET and the noncrystallizing copolymer PETG (, Ph.D. thesis, MIT, 2003). The materials were found to behave very similarly ... -
Uncertainty, Model Error, and Order Selection for Series-Expanded, Residual-Stress Inverse Solutions
(The American Society of Mechanical Engineers (ASME), 2006)Measuring the spatial variation of residual stresses often requires the solution of an elastic inverse problem such as a Volterra equation. Using a maximum likelihood estimate (least squares ... -
Design of Sandwich Panels With Prismatic Cores
(The American Society of Mechanical Engineers (ASME), 2006)The paper focuses on optimization of lightweight sandwich panels with prismatic cores subject to bending loads in the two principal in-plane directions. Comparisons are made with optimal designs ...