Journal of Energy Resources Technology: Recent submissions
Now showing items 2261-2280 of 3450
-
Running Force in Medium to High-Curvature Wellbores: An Experimental Study and Numerical Simulation of Laboratory and Field Cases
(The American Society of Mechanical Engineers (ASME), 2001)This paper presents a novel approach to measure and estimate running force for various laboratory and field conditions. The experimental and simulation procedures of different rod/pipe sizes ... -
Mass Transfer Coefficient Measurement in Water/Oil/Gas Multiphase Flow
(The American Society of Mechanical Engineers (ASME), 2001)Mass transfer studies in oil-containing multiphase flow provide fundamental knowledge towards the understanding of hydrodynamics and the subsequent effect on corrosion in pipelines. Mass transfer ... -
Investigation of the Effects of Completion Geometry on Single-Phase Liquid Flow Behavior in Horizontal Wells
(The American Society of Mechanical Engineers (ASME), 2001)The fluids in horizontal wells can exhibit complicated flow behaviors, in part due to interaction between the main flow and the influxes along the wellbore, and due to completion geometries. ... -
Development of Constrained Equilibrium Codes and Their Applications in Nonequilibrium Thermodynamics
(The American Society of Mechanical Engineers (ASME), 2001)Two constrained equilibrium codes, GNASA and GSTANJAN, have been developed which determine the composition of constrained equilibrium gas mixture. These codes use NASA and STANJAN equilibrium ... -
Laser-Induced Fluorescence Measurements in Venturi-Cascaded Propane Gas Jet Flames
(The American Society of Mechanical Engineers (ASME), 2001)Venturi-cascading is a technique to control pollutant emissions from diffusion flames by modifying air infusion and fuel-air mixing rates through changing the flow dynamics in the combustion zone ... -
Drillstring Stability Based on Variable Material Specific Force and Using a Sharp Three-Insert Polycrystalline Diamond Compact (PDC) Coring Bit
(The American Society of Mechanical Engineers (ASME), 2001)Previous research in stability of drillstrings was based on the assumption of constant material specific force, i.e., a bit force that is proportional to the area of cut. Moreover, earlier ... -
Visualizing Diffusion Flame Formation in the Wake of Partially Premixed Combustion
(The American Society of Mechanical Engineers (ASME), 2001)Results are presented on the formation of a diffusion flame in a methane nonpremixed jet following the propagation of partially premixed combustion. An initially nonreacting turbulent methane jet ... -
Performance of a Residential-Sized GAX Absorption Chiller
(The American Society of Mechanical Engineers (ASME), 2001)This research effort involved experimentally testing an advanced-cycle, ammonia-water absorption chiller with a cooling capacity of 17.6 kW (5 refrigeration tons (RT)). The system was a ... -
Investigation of Paraffin Deposition During Multiphase Flow in Pipelines and Wellbores—Part 2: Modeling
(The American Society of Mechanical Engineers (ASME), 2001)A Joint Industry Project to investigate paraffin deposition in multiphase flowlines and wellbores was initiated at The University of Tulsa in May 1995. As part of this JIP, a computer program, ... -
Entropies of Statistical Mechanics and Disorder Versus the Entropy of Thermodynamics and Order
(The American Society of Mechanical Engineers (ASME), 2001)The prevailing beliefs in the scientific and engineering literature are that: (i) thermodynamics is explained and justified by statistical mechanics; (ii) entropy is a statistical measure of ... -
Combined Heat and Mass Transfer Under Different Inlet Subcooling Modes During NH3-H2O Falling Film Absorption Process
(The American Society of Mechanical Engineers (ASME), 2001)Experiments were conducted for ammonia-water falling film absorption in a plate heat exchanger with offset strip fins. The objectives of this paper were to analyze combined heat and mass transfer ... -
An Update on Heat Transfer in a Porous Insulation Medium in a Subsea Bundled Pipeline
(The American Society of Mechanical Engineers (ASME), 2001)At the Multiphase ’99 Conference in Cannes, France, the authors presented a simple, yet general, formulation for effective conductivity of a porous insulation medium under pipeline application ... -
Limits of the Turbine Efficiency for Free Fluid Flow
(The American Society of Mechanical Engineers (ASME), 2001)An accurate estimate of the theoretical power limit of turbines in free fluid flows is important because of growing interest in the development of wind power and zero-head water power resources. ... -
Comparison of Externally Fired and Internal Combustion Gas Turbines Using Biomass Fuel
(The American Society of Mechanical Engineers (ASME), 2001)There is a difference of opinion regarding the relative merits of gas turbines using biomass fuels. Some engineers believe that the internal combustion gas turbine coupled to a gasifier will ... -
Solids Transport in Multiphase Flows—Application to High-Viscosity Systems
(The American Society of Mechanical Engineers (ASME), 2001)Solids transport in multiphase systems falls under the umbrella of “flow assurance.” Unlike issues such as waxes and hydrates, solids transport has received relatively little attention to date. ... -
Mapping of Permeability Damage Around Perforation Tunnels
(The American Society of Mechanical Engineers (ASME), 2001)We have investigated porosity and permeability damage around perforations using a combination of transient analysis and X-ray CT. The method applied allowed us to perform the entire experiments ... -
Modeling of Vertical Core-Annular Flows and Application to Heavy Oil Production
(The American Society of Mechanical Engineers (ASME), 2001)The use of core-annular flow pattern may be attractive as an artificial lift method in heavy oil wells. This flow pattern can be induced by the lateral injection of relatively small quantities ... -
Edison Patent Award Recipient
(The American Society of Mechanical Engineers (ASME), 2001)Grahic Jump Location -
Modeling Solid Particle Erosion in Elbows and Plugged Tees
(The American Society of Mechanical Engineers (ASME), 2001)Predicted erosion patterns on the surface of a pipe fitting can now be obtained using a technique implemented into a computational fluid dynamics (CFD) code. This comprehensive erosion prediction ... -
The Effect of Dynamical Parameters on Precession in Rotary Drilling
(The American Society of Mechanical Engineers (ASME), 2001)Precession, which is the rolling motion of the drillstring on the walls of the borehole, is investigated by considering the various possible motions of a rotating disk in a circular hole. Due ...