Now showing items 2281-2300 of 3450

    • A Comparison of Methods for Optimizing Air-Conditioning Systems According to the Exergonomic Approach 

      Luigi Marletta (The American Society of Mechanical Engineers (ASME), 2001)
      This paper discusses the comparison of three different methods for the optimization of an air-conditioning system from an exergonomic point of view. The reference design is an all air system ...
    • Horizontal Well Path Planning and Correction Using Optimization Techniques 

      Roger C. McCann; P. V. R. Suryanarayana; Assoc. Mem. ASME (The American Society of Mechanical Engineers (ASME), 2001)
      We present a procedure that uses nonlinear optimization theory to plan complex, three-dimensional well paths and path corrections while drilling. The problem of hitting a 3-D target is posed ...
    • Development and Application to a Real Scenario of a Design for Environment Methodology for Power Plants 

      L. Cedola; G. Di Stasio (The American Society of Mechanical Engineers (ASME), 2001)
      Power plants use burning processes with a heavy environmental impact. Traditional design models aim to optimize economic and thermodynamic performances. Owing to the new sensitivity arising towards ...
    • Oil-Water Two-Phase Flows in Large-Diameter Pipelines 

      H. Shi; J. Cai; W. P. Jepson (The American Society of Mechanical Engineers (ASME), 2001)
      Two-phase oil-water flows in a 10-cm-dia horizontal pipe have been experimentally investigated to study the effect of surfactant on oil-water distributions. Results show that at input water cut ...
    • Transient Pig Motion Through Gas and Liquid Pipelines 

      A. O. Nieckele; A. M. B. Braga; L. F. A. Azevedo (The American Society of Mechanical Engineers (ASME), 2001)
      Simulation of the transient motion of pigs through liquid and gas pipelines is presented. The differential form of the mass and linear momentum equations for compressible liquid and gas flows ...
    • An Experimental Comparison Between a Recombined Hydrocarbon-Water Fluid and a Model Fluid System in Three-Phase Pipe Flow 

      Ole Harald Utvik; Trygve Rinde; Arne Valle (The American Society of Mechanical Engineers (ASME), 2001)
      In this paper, results are presented from an experimental comparison between a light hydrocarbon system from the North Sea and a model oil system in pipe flow. The experiments were carried ...
    • Pressure Loss/Gain Boundary of Gas-Liquid Downward Flow in Inclined and Vertical Pipes 

      X. Tom Chen; Hong-Quan Zhang; Clifford L. Redus; James P. Brill (The American Society of Mechanical Engineers (ASME), 2000)
      Gas-liquid downward flow is frequently encountered in hilly-terrain pipelines, downcomer pipes extending from offshore production platforms to sea floors, and steam injection wells in thermal ...
    • Investigation of Transition From Annular to Intermittent Flow in Pipes 

      Avni Serdar Kaya; X. Tom Chen; Cem Sarica; James P. Brill (The American Society of Mechanical Engineers (ASME), 2000)
      A new unified model is proposed for the transition from annular to intermittent flow patterns for the entire range of pipe inclination angles. Experimentally, it has been observed that the ...
    • Velocity Fields of Nonpremixed Bluff-Body Stabilized Flames 

      R. F. Huang; C. L. Lin (The American Society of Mechanical Engineers (ASME), 2000)
      The velocity fields of nonpremixed circular-disk stabilized flames are measured by a two-component laser Doppler velocimeter. The results are presented in different flow regimes: prepenetration, ...
    • Stick-Slip and Bit-Bounce of Deep-Hole Drillstrings 

      A. Baumgart (The American Society of Mechanical Engineers (ASME), 2000)
      A mathematical model for the drilling process is derived and solved numerically as an initial value problem. The equations of motion are nonlinear differential equations for longitudinal, lateral, ...
    • The Trade-Off Between N2, NO, and N2O Under Fluidized Bed Combustor Conditions 

      C. Wartha; F. Winter; H. Hofbauer (The American Society of Mechanical Engineers (ASME), 2000)
      NO and N2O are harmful pollutants. Under fluidized bed combustor conditions, the nitrogen of the solid fuel is partly converted to these species. The trade-off between N2, NO, and N2O depends ...
    • Hydraulic Hammer Drilling Technology: Developments and Capabilities 

      Yuri Melamed; Michael Gelfgat; Don Dreesen; James Blacic; Andrei Kiselev (The American Society of Mechanical Engineers (ASME), 2000)
      Percussion drilling technology was considered many years ago as one of the best approaches for hard rock drilling. Unfortunately, the efficiency of most hydraulic hammer (HH) designs was very ...
    • The Nonoriented, Multiple Passageway Flowline Connection System 

      Gary Galle; Rudolf Bond (The American Society of Mechanical Engineers (ASME), 2000)
      The remote, diverless, simultaneous connection of multiple subsea flowlines has historically been a difficult and costly operation. Difficulties and intensified operational activities stem from the ...
    • Slug Dynamics in Gas-Liquid Pipe Flow 

      Hong-Quan Zhang; Subash S. Jayawardena; Clifford L. Redus; James P. Brill (The American Society of Mechanical Engineers (ASME), 2000)
      The continuity and momentum equations for fully developed and spatially developing slug flows are established by considering the entire film zone as the control volume. They are used for the ...
    • Sand Production Management 

      Mamdouh M. Salama (The American Society of Mechanical Engineers (ASME), 2000)
      Sand production may be inevitable in many fields that have a relatively low formation strength. Sand erosion and settling predictions and sand monitoring are important elements of any effective ...
    • Pressure Transients Across Constrictions 

      Michael A. Adewumi; E. S. Eltohami; W. H. Ahmed (The American Society of Mechanical Engineers (ASME), 2000)
      The modeling of pressure transient across constrictions is achieved by using a one-dimensional, isothermal, noncompositional, single-phase representation of the Eulerian model. A TVD scheme was ...
    • Advanced Geothermal Wellbore Hydraulics Model 

      Shifeng Tian; John T. Finger (The American Society of Mechanical Engineers (ASME), 2000)
      A model has been developed to simulate multiphase flow in the wellbore and heat transfer processes between the well and formations. The model is capable of handling dynamic well depth during ...
    • An Alternative to API 14E Erosional Velocity Limits for Sand-Laden Fluids 

      Mamdouh M. Salama (The American Society of Mechanical Engineers (ASME), 2000)
      The current practice for eliminating erosional problems in piping systems is to limit the flow velocity (Ve) to that established by the recommended practice API RP 14E based on an empirical ...
    • Optimization of Well Placement 

      Baris Guyaguler; Roland Horne (The American Society of Mechanical Engineers (ASME), 2000)
      Optimal placement of oil, gas or water wells is a complex problem that depends on reservoir and fluid properties, well and surface equipment specifications, as well as economic parameters. An ...
    • Estimation of the Thermodynamic Properties of Branched Hydrocarbons 

      Hui He; James C. Keck; Mohamad Metghalchi (The American Society of Mechanical Engineers (ASME), 2000)
      A simple model has been developed to estimate the sensible thermodynamic properties such as Gibbs free energy, enthalpy, heat capacity, and entropy of hydrocarbons over a wide range of temperatures ...