Journal of Energy Resources Technology: Recent submissions
Now showing items 1381-1400 of 3450
-
Emissions From a Diesel Engine Operating in a Dual-Fuel Mode Using Port-Fuel Injection of Heated Hydrous Ethanol
(The American Society of Mechanical Engineers (ASME), 2017)Aftermarket dual-fuel injection systems in diesel engines using hydrous ethanol as secondary fuel have been developed as a means to lower emissions from older diesel-powered equipment. However, our previous work has shown ... -
A Case Study on the Influence of Selected Parameters on Microexplosion Behavior of Water in Biodiesel Emulsion Droplets
(The American Society of Mechanical Engineers (ASME), 2017)Microexplosion behavior of water in biodiesel emulsion droplets was studied by suspending a single droplet on a wire type thermocouple. Water in biodiesel emulsion droplets with 9%, 12%, 15%, and 18% water by volume was ... -
Quantification of a Single Gas Bubble Growth in Solvent(s)–CO2–Heavy Oil Systems With Consideration of Multicomponent Diffusion Under Nonequilibrium Conditions
(The American Society of Mechanical Engineers (ASME), 2017)A mechanistic model has been developed and validated to quantify a single gas bubble growth with considering multicomponent gas diffusion in solvent(s)–CO2–heavy oil systems under nonequilibrium conditions. Experimentally, ... -
Use of Computational Combustion in the Development and Design of Energy-Efficient Household Cooker-Top Burners
(The American Society of Mechanical Engineers (ASME), 2017)In order to design energy efficient cooker-top burners, the stabilization mechanisms of partially premixed flames were investigated. Different design features are assessed with the identical fuel (CH4), fuel flow rate, and ... -
The Effects of Inlet Turbulence Intensity and Computational Domain on a Nonpremixed Bluff-Body Flame
(The American Society of Mechanical Engineers (ASME), 2017)A bluff body burner was investigated using computational fluid dynamics (CFD) to assess the effects of inlet turbulence intensity and compare the combustion characteristics with and without the bluff-body modeled in the ... -
Modeling of Energy and Exergy Efficiencies of a Wind Turbine Based on the Blade Element Momentum Theory Under Different Roughness Intensities
(The American Society of Mechanical Engineers (ASME), 2017)In this study, the analysis of energy and exergy of a horizontal axis wind turbine based on blade element momentum (BEM) theory is presented. The computations are validated against wind tunnel data measured in the MEXICO ... -
Ash Fusibility Based on Modes of Occurrence and High-Temperature Behaviors of Mineral Matter in Coals
(The American Society of Mechanical Engineers (ASME), 2017)Complete quantitative data of the chemical (proximate, ultimate, and ash analyses) and mineral (in low-temperature ash (LTA) and various high-temperature ashes (HTA)) compositions of 21 coals were used to investigate the ... -
Gelation Performance and Feasibility Study of an Environmental Friendly Improved Inorganic Aluminum Gel for Conformance Control Under Harsh Reservoir Conditions
(The American Society of Mechanical Engineers (ASME), 2017)Despite its successful application in controlling excessive water production in many mature oilfields, polymer gel is facing some application limitations under harsh reservoir conditions. To settle these problems, an ... -
Evaluation of Heat and Mass Transfer Models for Sizing Low-Temperature Kalina Cycle Microchannel Condensers
(The American Society of Mechanical Engineers (ASME), 2017)Waste heat driven ammonia/water Kalina cycles have shown promise for improving the efficiency of electricity production from low-temperature reservoirs (T < 150 °C). However, there has been limited application of these ... -
A Comparative Analysis of Single Nozzle and Multiple Nozzles Arrangements for Syngas Combustion in Heavy Duty Gas Turbine
(The American Society of Mechanical Engineers (ASME), 2017)Heavy duty gas turbines are the core components in the integrated gasification combined cycle (IGCC) system. Different from the conventional fuel for gas turbine such as natural gas and light diesel, the combustible component ... -
The State of the Art and Challenges in Geomechanical Modeling of Injector Wells: A Review Paper
(The American Society of Mechanical Engineers (ASME), 2017)Fluid injection is a common practice in the oil and gas industry found in many applications such as waterflooding and disposal of produced fluids. Maintaining high injection rates is crucial to guarantee the economic success ... -
Nanotechnology in Batteries
(The American Society of Mechanical Engineers (ASME), 2017)A relatively new field, nanotechnology has seen an expansion onto almost every scientific sector since its origin in the 1980s. This work focuses on the potential of nanotechnology in batteries, in particular, with a review ... -
Reviewer Index and Reviewers of the Year
(The American Society of Mechanical Engineers (ASME), 2017) -
Experimental Study and Application of Steam Flooding for Horizontal Well in Ultraheavy Oil Reservoirs
(The American Society of Mechanical Engineers (ASME), 2017)Based on the ultraheavy oil area in AL-1 Block, Shengli Oilfield, China, a two-dimensional (2D) high-temperature–high-pressure (HTHP) visualized scaled physical simulation system was constructed to investigate intensively ... -
Investigation of CO2–CH4 Displacement and Transport in Shale for Enhanced Shale Gas Recovery and CO2 Sequestration
(The American Society of Mechanical Engineers (ASME), 2017)To gain a better understanding of the enhanced shale gas recovery by CO2 gas injection (CO2-ESGR) technique, the dynamic displacement mechanism of CO2–CH4, the CO2 enhanced shale gas recovery (RCH4), and CO2 storage capacity ... -
Experimental Study on a New Type of Water Shutoff Agent Used in Fractured Low Permeability Reservoir
(The American Society of Mechanical Engineers (ASME), 2017)In order to effectively plug the fracture channeling-path in the high water cut fractured low permeability reservoir, a new type of water shutoff agent is developed by bottle tests and its injectivity and plugging performance ... -
Hydrogen Production by Carbon-Catalyzed Methane Decomposition Via Thermogravimetry
(The American Society of Mechanical Engineers (ASME), 2017)Hydrogen is a high energy content fuel and methane is currently the most preferred feedstock for hydrogen production. Direct thermal splitting of methane offers the cleanest technique to produce hydrogen and carbon as ... -
Optimal Design of a Solar Collector for Required Flux Distribution on a Tubular Receiver
(The American Society of Mechanical Engineers (ASME), 2017)A mathematical model has been derived and used to develop a three-dimensional concentrating solar collector as presented in this article. The developed solar collector gives the required flux distribution along the ... -
Comparison of Leakage Characteristics of Viton and Polytetrafluoroethylene Seals in Gas-Lift Valve Applications
(The American Society of Mechanical Engineers (ASME), 2017)The present research article focuses on comparing the leakage characteristics of Viton and polytetrafluoroethylene (PTFE) seals used in enhanced oil-recovery system. The objective of the study is also to validate if each ... -
Simultaneous Schlieren–PLIF Studies for Ignition and Soot Luminosity Visualization With Close-Coupled High-Pressure Double Injections of n-Dodecane
(The American Society of Mechanical Engineers (ASME), 2017)Studies are performed in a constant volume preburn type combustion vessel over a range of ambient temperatures (750 K, 800 K, and 900 K) at constant density (22.8 kg/m3) with 15% O2 by volume in the ambient at 1200 bar ...