Journal of Heat Transfer: Recent submissions
Now showing items 3581-3600 of 3611
-
Heat Transfer Enhancement for Turbulent Flow Through Blockages With Round and Elongated Holes in a Rectangular Channel
(The American Society of Mechanical Engineers (ASME), 2007)Experiments were conducted to determine the average heat transfer coefficients on three wall segments between blockages with holes in a wide rectangular channel. Eight different configurations of ... -
The Parametric Study of an Innovative Offset Strip-Fin Heat Exchanger
(The American Society of Mechanical Engineers (ASME), 2007)Offset strip-fin heat exchangers have numerous applications throughout various industries because they can provide a large amount of heat transfer area in a small volume. The widespread use of ... -
The Modeling of Viscous Dissipation in a Saturated Porous Medium
(The American Society of Mechanical Engineers (ASME), 2007)A critical review is made of recent studies of the modeling of viscous dissipation in a saturated porous medium, with applications to either forced convection or natural convection. Alternative ... -
Thermomechanical Formation of Nanoscale Polymer Indents With a Heated Silicon Tip
(The American Society of Mechanical Engineers (ASME), 2007)In thermomechanical data storage, a heated atomic force microscope cantilever tip is in contact with and scans over a polymer film. Heating in the cantilever and cantilever tip induces local ... -
On the Transient Analysis of a V-Shaped Microgrooved Heat Pipe
(The American Society of Mechanical Engineers (ASME), 2007)In this paper, we present a transient mathematical model for a V-shaped microgrooved heat pipe considering the temporal variations in the fluid flow, and heat and mass transfer, and utilizing ... -
Detailed Heat/Mass Transfer Distributions in a Rotating Smooth Channel With Bleed Flow
(The American Society of Mechanical Engineers (ASME), 2007)In this study, the effects of bleed flow on heat/mass transfer in a rotating smooth square channel were investigated. The hydraulic diameter (Dh) of the channel was 40.0mm, and the diameter ... -
A Convection Heat Transfer Correlation for a Binary Air-Helium Mixture at Low Reynolds Number
(The American Society of Mechanical Engineers (ASME), 2007)The results of experiments investigating heat transfer from a hot wire in a binary mixture of air and helium are reported. The measurements were made with a constant temperature anemometer at ... -
A General Scheme for the Boundary Conditions in Convective and Diffusive Heat Transfer With Immersed Boundary Methods
(The American Society of Mechanical Engineers (ASME), 2007)We describe the implementation of an interpolation technique, which allows the accurate imposition of the Dirichlet, Neumann, and mixed (Robin) boundary conditions on complex geometries using the ... -
Heat (Mass) Transfer Distribution in a Two-Pass Trapezoidal Channel With a 180deg Turn
(The American Society of Mechanical Engineers (ASME), 2007)The heat transfer characteristics of airflows in serpentine cooling channels in stator vanes of gas turbines were studied. The cooling channels were modeled as a two-pass trapezoidal channel ... -
Experimental Investigation of the Heat Transfer Characteristics of Aluminum-Foam Heat Sinks With Restricted Flow Outlet
(The American Society of Mechanical Engineers (ASME), 2007)This study investigates the heat transfer characteristics of aluminum-foam heat sinks with restricted flow outlets under impinging-jet flow conditions. An annular flow-restricting mask is used to ... -
High Knudsen Number Physical Vapor Deposition: Predicting Deposition Rates and Uniformity
(The American Society of Mechanical Engineers (ASME), 2007)The problem of predicting deposition rates and film thickness variation is relevant to many high-vacuum physical vapor deposition (PVD) processes. Analytical methods for modeling the molecular ... -
Heat Transfer and Fluid Flow Characteristics of Separated Flows Encountered in a Backward-Facing Step Under the Effect of Suction and Blowing
(The American Society of Mechanical Engineers (ASME), 2007)Numerical investigation of heat transfer and fluid flow over a backward-facing step (BFS), under the effect of suction and blowing, is presented. Here, suction/blowing is implemented on the ... -
Fully Developed Couette Flow of Three Fluids With Variable Thermophysical Properties Flowing Through a Porous Medium Channel Heated Asymmetrically With Large Temperature Differences
(The American Society of Mechanical Engineers (ASME), 2007)In this paper, we study the steady laminar flow in a fluid-saturated porous medium channel bounded by two parallel plates with constant but unequal temperatures. One plate is moving with ... -
Flow and Heat Transfer Characteristics in Rectangular Channels With Staggered Transverse Ribs on Two Opposite Walls
(The American Society of Mechanical Engineers (ASME), 2007)The flow characteristics and the heat transfer properties of the rectangular channels with staggered transverse ribs on two opposite walls are experimentally studied. The rib height to channel ... -
Parametric Study of Pool Boiling on Horizontal Highly Conductive Microporous Coated Surfaces
(The American Society of Mechanical Engineers (ASME), 2007)To better understand the mechanisms that govern the behavior of pool boiling on horizontal highly conductive microporous coated surfaces, a series of experimental investigations were designed to ... -
A Coupled Map Lattice Model of Flow Boiling in a Horizontal Tube
(The American Society of Mechanical Engineers (ASME), 2007)In this work laminar, stratified flow boiling of water is simulated qualitatively by the coupled map lattice (CML) method. The liquid is entering a constant wall temperature horizontal tube ... -
Experimental Evaluation of Marangoni Shear in the Contact Line Region of an Evaporating 99+% Pure Octane Meniscus
(The American Society of Mechanical Engineers (ASME), 2007)Image analyzing interferometry was used to study the spreading characteristics of an evaporating octane meniscus (purity: 99+%) on a quartz surface. The thickness, slope, and curvature profiles ... -
Effect of Vapor Velocity on Condensation of Low-Pressure Steam on Integral-Fin Tubes
(The American Society of Mechanical Engineers (ASME), 2007)Experimental data are presented for forced-convection condensation of low-pressure steam on a set of single, integral-fin tubes. The five tubes had fin-root diameter of 12.7mm and identical fin ... -
The Onset of Convection in a Porous Medium Occupying an Enclosure of Variable Width or Height
(The American Society of Mechanical Engineers (ASME), 2007)An analytical study is made of the onset of convection in a saturated porous medium occupying a two-dimensional enclosure of uniform height, but whose width is slowly varying in an arbitrary ... -
A Methodology for Blast Furnace Hearth Inner Profile Analysis
(The American Society of Mechanical Engineers (ASME), 2007)The wear of a blast furnace hearth and the hearth inner profile are highly dependent on the liquid iron flow pattern, refractory temperatures, and temperature distributions at the hot face. ...