Journal of Heat Transfer: Recent submissions
Now showing items 3561-3580 of 3611
-
Discussion: “Performance and Optimization Analysis for Fins of Straight Taper with Simultaneous Heat and Mass Transfer” (Kundu, B., and Das, P. K., 2004, ASME J. Heat Transfer, 126, pp. 862–868)
(The American Society of Mechanical Engineers (ASME), 2007)In this paper the authors employed a new rather unorthodox approach, and unusual parameterization entirely different from that existing in the literature, to obtain their results. In their ... -
Discussion: “Heat Transfer and Wall Heat Flux Partitioning During Subcooled Flow Nucleate Boiling–A Review” (Warrier, G.R., and Dhir, V.K., 2006, Journal of Heat Transfer, 128, pp. 1243–1256)
(The American Society of Mechanical Engineers (ASME), 2007)In their paper (1), the authors state on p. 1245 that Boyd and Meng (2) in 1996 suggested an interpolation method for calculating the heat transfer characteristics in the partial boiling ... -
Thermal Optimization of an Internally Finned Tube Using Analytical Solutions Based on a Porous Medium Approach
(The American Society of Mechanical Engineers (ASME), 2007)The present work deals with thermal optimization of an internally finned tube having axial straight fins with axially uniform heat flux and peripherally uniform temperature at the wall. The ... -
Spectral Element Approach for Coupled Radiative and Conductive Heat Transfer in Semitransparent Medium
(The American Society of Mechanical Engineers (ASME), 2007)A spectral element method is presented to solve coupled radiative and conductive heat transfer problems in multidimensional semitransparent medium. The solution of radiative energy source is based ... -
Novel Design of a Miniature Loop Heat Pipe Evaporator for Electronic Cooling
(The American Society of Mechanical Engineers (ASME), 2007)Miniature loop heat pipes (mLHPs) are coming up with a promising solution for the thermal management of futuristic electronics systems. In order to implement these devices inside compact ... -
Heat Transfer Study in a Linear Turbine Cascade Using a Thermal Boundary Layer Measurement Technique
(The American Society of Mechanical Engineers (ASME), 2007)An experimental system is designed, constructed, and operated to make local measurements of heat transfer from constant-temperature surfaces in a linear turbine cascade. The system includes a ... -
Natural-Convection Flow Along a Vertical Complex Wavy Surface With Uniform Heat Flux
(The American Society of Mechanical Engineers (ASME), 2007)A natural-convection boundary layer along a vertical complex wavy surface with uniform heat flux has been investigated. The complex surface studied combines two sinusoidal functions, a fundamental ... -
Experimental and Numerical Study of a Stacked Microchannel Heat Sink for Liquid Cooling of Microelectronic Devices
(The American Society of Mechanical Engineers (ASME), 2007)One of the promising liquid cooling techniques for microelectronics is attaching a microchannel heat sink to, or directly fabricating microchannels on, the inactive side of the chip. A stacked ... -
Numerical Evaluation of Fin Performance Under Dehumidifying Conditions
(The American Society of Mechanical Engineers (ASME), 2007)A numerical model of moist air cooling in compact heat exchangers is presented. The model requires the solution of a coupled problem, since interface temperatures, obtained from the solution ... -
An Experimental Study of Shell-and-Tube Heat Exchangers With Continuous Helical Baffles
(The American Society of Mechanical Engineers (ASME), 2007)Two shell-and-tube heat exchangers (STHXs) using continuous helical baffles instead of segmental baffles used in conventional STHXs were proposed, designed, and tested in this study. The two ... -
Quantitative Salt-Water Modeling of Fire-Induced Flows for Convective Heat Transfer Model Development
(The American Society of Mechanical Engineers (ASME), 2007)This research provides a detailed analysis of convective heat transfer in ceiling jets by using a quantitative salt-water modeling technique. The methodology of quantitative salt-water modeling ... -
Homogeneous Nucleation of Vapor at Preferred Sites During Rapid Transient Heating of Liquid in Micropassages
(The American Society of Mechanical Engineers (ASME), 2007)Rapid heating of a liquid at the wall of a micropassage may produce homogeneous nucleation of vapor in the liquid in contact with the surface. In such circumstances, nucleation is generally ... -
Characteristics of Flow Boiling Oscillations in Silicon Microchannel Heat Sinks
(The American Society of Mechanical Engineers (ASME), 2007)Flow boiling oscillation characteristics in two silicon microchannel heat sink configurations are presented. One is a standard heat sink with 45 straight parallel channels, whereas the second is ... -
Internal Condensing Flows inside a Vertical Pipe: Experimental/Computational Investigations of the Effects of Specified and Unspecified (Free) Conditions at Exit
(The American Society of Mechanical Engineers (ASME), 2007)Reported experimental and computational results confirm that both the flow features and heat-transfer rates inside a condenser depend on the specification of inlet, wall, and exit conditions. The ... -
Combined Parameter and Function Estimation With Application to Thermal Conductivity and Surface Heat Flux
(The American Society of Mechanical Engineers (ASME), 2007)This is a numerical and experimental study on the combined parameter and function estimation. The determination of thermal conductivity and the surface heat flux is an illustration of combined ... -
Flow Boiling Heat Transfer in Microchannels
(The American Society of Mechanical Engineers (ASME), 2007)Flow boiling heat transfer to water in microchannels is experimentally investigated. The dimensions of the microchannels considered are 275×636 and 406×1063μm2. The experiments are conducted ... -
Influence of Partition Length on Natural Convection in Partially Divided Square Enclosure
(The American Society of Mechanical Engineers (ASME), 2007)Numerical investigation is carried out for natural convection in square enclosures consisting of partitions protruding from the end walls with different thermal boundary conditions at the end ... -
Transition Boiling Heat Transfer of Droplet Streams and Sprays
(The American Society of Mechanical Engineers (ASME), 2007)An experimental study was performed to characterize the transition boiling heat transfer rate from a surface to a stream of impinging water droplets and to extrapolate this information to predict ... -
Thermal Control Utilizing an Electrohydrodynamic Conduction Pump in a Two-Phase Loop With High Heat Flux Source
(The American Society of Mechanical Engineers (ASME), 2007)The electric field applied in dielectric fluids causes an imbalance in the dissociation-recombination reaction generating free space charges. The generated charges are redistributed by the applied ... -
Flow, Thermal, Energy Transfer, and Entropy Generation Characteristics Inside Wavy Enclosures Filled With Microstructures
(The American Society of Mechanical Engineers (ASME), 2007)Flow, thermal, energy, and irreversibility characteristics inside wavy enclosures packed with microstructures are reported in this paper. It is assumed that the entire enclosure has sufficient and ...